Installation Guide

ManualsBrandstiv thaiv ManualsTW TRACEtivoli TW TRACE Horizontal

www.tivolilighting.com tel: 714-957-6101 fax: 714-427-3458

TW TRACE™ Horizontal Installation Instructions

7101011

Page 1 of 8

Please verify the contents of the packages!

Please read instructions entirely before starting

installation

Be sure power is turned off before installing the system

Call Tivoli, LLC tech support with questions

Caution: TRACE™ TW is designed to work with listed Class 2 24V

DC transformers only. Use of any other power source will cause

damage, shorten the life of the fixture and will void the warranty.

Consult any and all applicable local and national codes for

installation.

Do not conceal or extend exposed conductors through a building

wall as per local electrical code.

Warning: With any luminaire for any application, basic safety

precautions should always be followed to reduce the risk of fire,

electric shock and personal injuries. This lighting system should be

installed by a certified professional.

TRACE™ is an indoor/outdoor low voltage lighting system

used primarily for direct or indirect lighting designs.

Proles:

/”

/”

/”

/”

TRACE™ Horizontal

IP67

Trace™ Horizontal

Do not allow to twist or bend in the wrong direction.

WARNINGS

Keep Trace™ from twisting or bending in the wrong direction.

Two person installation.

WARNING! Risk of product damage.

Longer runs of Trace™ lighting strands must be installed by at least

two people.

IMPORTANT! The Trace™ luminaire must not be allowed to bend or

hang down. That way, the bending limit will not be inadvertently

exceeded, resulting in product damage.

TRACE™ TUNABLE WHITE MAY BE EASILY DAMAGED! The

reliability of the product can only be ensured if these warnings and

cautions are complied with faithfully. Keep these instructions for

future maintenance work.

Warning! Risk of product damage.

Trace™ Tunable White Horizontal must not be bent at less than 2.0” diameter or damage will result. Do not allow Trace™ to twist or bend

in the wrong direction.

WARNING! Risk of Damage.

Insert Trace™ Tunable White

Horizontal into channel

evenly and gradually

to keep twisting and

bending to a minimum.

Bending

Diameter

2.0”

Summary of content (8 pages)

PAGE 1
TW TRACE™ Horizontal Installation Instructions Please verify the contents of the packages! Profiles: 7/8” 13/16” 11/16” 15/32” TRACE™ Horizontal TRACE™ is an indoor/outdoor low voltage lighting system used primarily for direct or indirect lighting designs.
PAGE 2
TW TRACE™ Horizontal Installation Instructions Overview: Read Before Installing Luminaire Installation Notes: Step 1: Measure run area where Trace™ TW is to be installed. Locate power feed end at highest point of the run to minimize exposure to water run off. Step 2: A Mounting Channel is recommended for outdoor applications. Lay channel along desired area and attach with screws (by others) every 18 to 24 inches.
PAGE 3
TW TRACE™ Horizontal Installation Instructions Trace™ Tunable White Mounting Options Trace™ Tunable White Horizontal with Mounting Clips Warning: Risk of Product Damage. Only bend the Trace™ TW Horizontal so the lens bends side to side. See diagram below. Note: Minimum bending diameter for Trace™ Horizontal is 2” in the horizontal direction only. Step 1: Determine where the Mounting Clips will need to be installed to achieve the desired shape.
PAGE 4
TW TRACE™ Horizontal Installation Instructions Trace Tunable White Mounting Options (Continued) Install Trace™ TW Horizontal in Notched Mounting Channel Warning: Risk of Product Damage. Only bend the Trace™ Horizontal so the lens bends side to side so as not to twist the Tape Light. See diagram. Bending direction for Trace Vertical Note: Minimum bending diameter for the notched channel is 11”. However, the minimum bending diameter for Trace™ Horizontal is 2” in the horizontal direction only.
PAGE 5
TW TRACE™ Horizontal Installation Instructions Trace Tunable White Mounting Options (Continued) Straight Channel for Trace™ TW Horizontal Installation Step 1: Prepare Straight Mounting Channel for installation cutting it to the correct length, keeping in mind that the End Caps will not fit inside the Channel, and by drilling screw holes 3” from each end and additional holes approximately every 18” along the channel. Step 2: Place Straight Channel on the mounting surface and mark the hole locations.
PAGE 6
TW TRACE™ Horizontal Installation Instructions Trace™ Tunable White Mounting Options (Continued) Note: Trace™ Mounting Channel can be mounted on horizontal or vertical surfaces. Product Specification Guide LUMINAIRE Trace TW, Low Output Trace TW, Standard Trace TW, High Output POWER CONSUMPTION MAX RUN LENGTH 1.5W 58’ 3W 29’ 4.5W 19’ 7101011 Copyright © 2022 Tivoli 08.08.22 Page 6 of 8 www.tivolilighting.
PAGE 7
TW TRACE™ Horizontal Installation Instructions Trace™ Tunable White Basic Wiring Diagram Elecrical Connections for Trace™ Tunable White Step 1: Turn power off before beginning electrical installation. Note: Contacting hot wires against the Trace™ leads may damage the product and void the warranty. Step 2: Connect Trace™ lead wires to RGB-Sub-Controller, or if using our ADUL-DIN series transformers, connect to pre-wired connectors which are found inside the power supply box.
PAGE 8
TW TRACE™ Horizontal Installation Instructions Power Supply with Sub-Controller Sample Wiring Diagram There are many possible options for controlling Trace™ TW. See the specification Sheet for more information. The following wiring diagram is for reference only. Please refer to the Installation Instruction for the Power Supply you choose for detailed wiring instructions.