Owner's manual

Page 23@)1&/2:(+.:4=&A02'/.)+'B&6=24'2&:4==&CD###DE#$D$EC#,Item 64804 64805
FG@<HIJGKLH<LGLM< NGFKM&O<PQKLRO<PQKLR&HKSF F<HTS
O2=>.+9&H.6'
A good way to test welding technique is to examine a
weld’s appearance after it has cooled and the slag
has been removed. Then, better welding can be
learned by adjusting your weld technique to remedy
any problems found.
M=24+.+9&/(2&O2=>
HV&SU<-<LH&F<UKVTF&KLcTUI5&
M)+/.+02&/)&*241&GLFKD4661)X2>&
'482/W&9)99=2'&4+>&61)/2:/.X2&*241&
*(2+&:=24+.+9&4&*2=>,&&
F641\'&)1&:(.6'&;4W&8=W&*(2+&:=24+.+9,
1. A weld from flux-cored wire will be
covered by slag. Use a chipping hammer
to knock this off. N2&:41280=&+)/&/)&
>4;492&/(2&*2=>&)1&34'2&;4/21.4=,
2. Use a wire brush to further clean the weld
or use an angle grinder (sold separately) to
shape the weld.
F/1.\2&H2'/
G&/2'/&*2=>&)+&4&SK<M<&V@&FMUGS&:4+&32&/2'/2>&3W&
0'.+9&/(2&8)==)*.+9&61):2>012,
O<GU&GLFKDGSSUV-<Q&FG@<HI&RVRRP<F&
QTUKLR&H]KF&SUVM<QTU<,
OGULKLRi&&H(.'&/2'/&OKPP&>4;492&/(2&*2=>&./&.'&
6218)1;2>&)+,&&H(.'&/2'/&.'&VLPI&4+&.+>.:4/)1&)8&*2=>&
/2:(+.A02&4+>&.'&+)/&.+/2+>2>&/)&/2'/&*)1\.+9&*2=>',
1. After two scraps have been welded together and the
weld has cooled, clamp one scrap in a sturdy vise.
2. Stay clear from underneath while you strike
the opposite scrap with a heavy hammer,
preferably a dead-blow hammer.
3. A RVVQ&O<PQ will deform but not break,
as shown on top.
A SVVU&O<PQ will be brittle and snap at the weld,
as shown on bottom.
:=4;6
FMUGS&
*)1\6.2:2
RVVQ&O<PQ&&
32+>'&4+>&.'&+)/&31.//=2
>24>D3=)*&(4;;21
:=4;6
FMUGS&
*)1\6.2:2
SVVU&O<PQ&&
'+46'&)1&:14:\'
>24>D3=)*&(4;;21
A typical solid wire (GMAW) weld &
328)12&:=24+.+9,
34'2&;2/4=
*2=>&324>
'64//21
A typical flux-cored wire (FCAW) weld &
328)12&:=24+.+9,
34'2&;2/4=
*2=>&324>
'=49
'64//21
M(.66.+9&
]4;;21
O.12&N10'(