Operator’s Manual PGD2875H
Table of Contents Introduction......................................................................................................2 Safety Warnings ..............................................................................................3 Main Parts…………………………………………………………………………….4 Preparation for Use…………………………………………………………………5 Operating Instructions.....................................................................................7 Service and Maintenance.............................................
Introduction Thank you for choosing Titan Gas-Powered Post Drivers. The performance of this machine is dependent upon your knowledge of the information contained in this operator’s manual and your understanding of the operation and care of the engine installed on your Titan Post Driver. This post driver is powered by a Honda GX35 engine. Honda supplies its own operator’s manual, which covers all aspects of operating and maintaining your Honda engine.
Safety Warnings 1. Always follow proper operation and maintenance instructions. 2. Always use approved Personal Protective Equipment (PPE). Operators and all other persons in the immediate working area must wear protective equipment as well. Noise emitted from the machine while working can reach above 100 decibels, which can also harm others in close proximity. We recommend the following personal protective equipment: a. Class 4 (SLC80 = 22.4 dB) hearing protection or greater b.
Main Parts No. 1 4 7 10 13 16 19 4 Part Name Oil Level Gauge Gas Tank Fuel Bubble Dampening Spring Hammer Case Combination Switch Throttle Cable No. 2 5 8 11 14 17 20 Part Name Handle Gas Cap Air Filter Handle Sleeve Serial No. Location Throttle Switch Piling Socket No.
Preparations For Use Installing Inner Pile Head If the inner pile head (#49) is not pressed on the shock (#43) at this time, you must slide the inner pile head inside the piling socket and match the small side with the shock. Tap the inner pile head a few times to make sure it is connected to the shock. As you start using your machine, the inner pile head will press further on the shock and will not separate again without the use of tools.
Adding Engine Oil 1. Before the first use, add engine oil. THE OIL IS NOT FILLED WHEN THE POST DRIVER IS ASSEMBLED. Honda suggests adding less than 80 cm2 (2.7 US oz., 2.8 Imp. oz.), then checking. Add oil if required to fill to the bottom edge of the oil fill hole. Use 10W-30 oil. DO NOT OVERFILL. Always place the driver in the horizontal position to check oil the level. Proper oil level is essential for the correct operation of the post driver.
Operating Instructions Starting 1. The Honda GX35 engine is inclinable, which means it can be stored and operated in any direction. BEFORE STARTING, the driver needs to be in the horizontal position for 5 minutes. 2. Before starting the post driver, press the transparent, semi-circle fuel bubble repeatedly until the carburetor is filled with fuel. If the engine is cool, place the choke lever to the "on" position. 3. Place one hand on the top engine cover with slight downward pressure.
Service and Maintenance Air Filter Maintenance After the driver has been used for some time, dirt and dust particles can block the flow of air, which will result in reduced power and increased oil consumption. It is necessary to clean the air filter regularly. The cleaning cycle is usually every 3 months or every 25 hours of operation. When using the driver in extremely dusty environments, clean it every 10 hours or even every day. Cleaning the Air Filter 1.
Spark Plug Maintenance If the spark plug has too much carbon deposit, it will result in poor engine performance. It is necessary to regularly maintain and adjust the spark plug every year or every 100 hours of operation. 1. Remove the spark plug as shown. 2. Remove carbon deposit. 3. Adjust to 0.6 – 0.7 mm. 4. Replace the spark plug. Replacing Engine Oil 1. Dirty engine oil will result in reduced service life of moving engine parts.
Lubrication of Gearbox and Impact Parts After 40 hours of use, open the gearbox cover, and add 75 Series Grease to the connecting rod to fully lubricate the machine as shown below.
Maintenance Schedule √ √ √ √ √ √ √ √ √ √ √ √ √ √ Tighten Reduction Gearbox/Impact Cylinder √ Clean √ Add Grease √ Check Muffler Cylinder Cooling Fin Spark Plug Remove Carbon Deposit Check Clean √ √ √ √ Check/Adjust √ Replace Check Screw and Nut Tighten If Necessary Check If Temporary Failure Fuel Tank/Fuel Tank Lid Every Month Fuel Filter Every Week Air Filter √ After Filling Oil Control Handle/Stop Button Clean Function Check Clean Replace Check Replace Clean After Each Use
Troubleshooting Example 1: Difficulty starting the engine. 1. 2. 3. 4. 5. 6. 7. Make sure the choke lever is in the "on" position (page 7). Remove the fuel in the tank, and replace it with fresh gasoline. Press the fuel bubble 3-4 times. Check to make sure the on/off switch is in the down position. Check the fuel filter (page 8). Check the air filter (page 8). Check the spark plug (page 11). Example 2: Difficulty starting after a sudden stop. 1. 2. 3. 4. Check the fuel level.
Key Product Data Engine Type Honda GX35 engine Model LxWxH (inches) Fuel Displacement Fuel Tank Volume Oil Capacity Weight Max Power and Corresponding Rotating Speed Max Torque and Corresponding Rotating Speed Fuel Consumption Rate Impact Frequency Impact Energy Spark Plug Type Starter System PGD2875H 25" x 10" x 13" 86 octane, unleaded gasoline or higher 35.8 cc 0.17 US gal 3.4 US oz 30 lbs 1.3 hp / 6,500 r/min 1.2 ft/lb / 5,500 r/min ≤ 0.
Exploded View of PGD2875H Driver 14
Parts List and Exploded View of PGD2875H Driver No. Part Name Qty No.
No. 51 52 53 54 55 56 57 58 59 60 61 62 16 Part Name Piling Socket Sleeve Connecting Thread Head Step Nut Handle Spring 38x27Xφ2.5 Handle Sleeve Handle Soft Sleeve Handle Nut Positioning Sleeve Handle Frame Handle Frame Soft Sleeve Inner Hexagon Cylindrical-Head Screw M6×40 Combination Switch Qty 1 2 2 4 1 1 1 2 1 1 2 1 No.
Warranty Titan Post Drivers will warrant to the original purchaser, who purchases the equipment in new condition and in its original packaging from an authorized dealer, that its gas-powered post driver will be free from defects in workmanship and materials for a period of one (1) year. This warranty period will commence on the date of retail purchase by the original purchaser. This warranty is non-transferrable beyond the original purchaser. Titan Post Drivers provides no warranty on the Honda engine.
Contact: Hours: Monday-Friday 8 AM to 5 PM CST Address: 713 E Austin Blvd, Nevada, MO 64772 Phone: (702) 293-4262 Email: info@titanpostdrivers.
Maintenance Records and Notes: ------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
