Manual

ManualsBrandsTippmann ManualsPaintballX-7 e-Grip

1). Prepare E-Grip

for installation:

WARNING

TIPPMANN

E-GRIP

KIT PART# T210001

INSTALLATION & PROGRAMMING INSTRUCTIONS

KIT PN.

T210001

INCLUDES:

❏

1 - X7

E-Grip

❏

READ EACH STEP COMPLETELY BEFORE

PERFORMING STEP.

EYE PROTECTION DESIGNED FOR PAINTBALL

USE MUST BE WORN AT ALL TIMES WHEN

HANDLING THIS MARKER BY THE USER AND

ANY PERSON WITHIN RANGE. DO NOT

DISASSEMBLE THIS MARKER WHILE IT IS

PRESSURIZED WITH AIR. REMOVE AIR

SUPPLY CYLINDER OR CARTRIDGE BEFORE

DOING ANY DISASSEMBLY. DISASSEMBLING

THE RECEIVER WHILE UNDER AIR PRESSURE

CAN CAUSE PERSONAL INJURY & /OR

DAMAGE TO THE MARKER. DO NOT OPERATE

THIS MARKER WITH PARTS MISSING OR

DAMAGED. IF DURING THE COURSE OF THIS

INSTALLATION, A PART IS LOST OR FOUND TO

BE DAMAGED, OBTAIN A REPLACEMENT PART

BEFORE CONTINUING REASSEMBLY.

STEP 1: Prepare Marker for SAFE

Disassembly before beginning disassembly.

STEP 2: Remove stock grip from marker.

❏

Set up a table with plenty of space to work.

You will need a 7/16” wrench (

) and a 9

volt battery. NOTE: Carefully hand start threaded

parts, do not over tighten and strip threads.

❏ ❏

❏

Do Not perform STEP 2 before reading the

warning section and completing

STEP 1.

(English - continued on page 2)

Eye protection designed for paintball use must be

worn by the user and any person within range.

1. Unload Your Marker - To unload your marker:

❏

1) Install the barrel sleeve.

❏

2) Empty and

remove the hopper (turn the hopper clockwise

and lift out).

❏

3) Go to a designated firing area

and remove the barrel sleeve.

❏

4) Point your

marker in a safe direction and fire several times to

be sure there are no balls lodged in the chamber and

/ or barrel.

❏

5) Visually inspect the Cyclone

Feeder and

chamber for paintballs.

2. Remove The Air Supply - To remove a charged

air supply cylinder:

❏

Turn the cylinder approximately 3/4 of a turn

counterclockwise

or out. This allows the air

supply pin valve to close so that no air will enter

the marker.

❏

Point the marker in a safe direction and

discharge the remaining gas in the marker by

pulling the trigger until the marker stops firing. This

may take 4-5 shots.

If your marker continues to

fire the tank pin valve has not closed yet (because

of the variances in tank pin valve parts, each tank

varies slightly on exactly how far it should be

turned) and

❏

you will have to turn the tank

counterclockwise

a little further and repeat

step-2) until the marker does not fire,

❏

then

remove the tank.

NOTE: If you turned the tank and it began to leak

before you pulled the trigger the tank o-ring should

be checked for damage before reassembly.

❏

3) After air tank is removed, point & fire the

marker in a safe direction until stored air is

completely discharged.

❏

4) Put marker in the uncocked position:

STEP 3: Install the new X7

E-Grip

❏

Slide the E-Grip

up onto the marker and

align the push pin holes.

❏

Insert the two push

pins

& .

❏ ❏

❏

3) Install the gas line - Thread tape or paste

are not needed for this connection.

Step 4: Power On - Basic Operation

❏

Use a small object

like an allen wrench

(

) to press and

hold the power button

for 2 seconds.

The LED

will light

orange then green

when the electronics

have been activated.

❏

Release the power

button and the green

LED

will begin

flashing green to show

the power is on and

the battery is good.

(If LED begins flashing

red, see - Low Battery

Condition).

❏ ❏

❏

2) Safety/Selector operation -

NOTE: 9V Battery

Not Included, but

Required

❏ ❏

❏

1) Remove the gas line from the grip:

Press the ends of the 2

push pins (

)

in and then pull push pins

out (

) .

❏

Pull and hold the bolt cocking handle back ;

❏ ❏

❏

1) To turn the X7

E-Grip

power on:

❏ ❏

❏

2) Remove the 2 grip push pins / :

❏ ❏

❏

3) Remove the grip:

Pull down

on the grip

to slide it off.

❏ ❏

❏

4) Install the battery -

❏

Remove the battery door from

the back of the new grip by

pulling up and back on the tab.

❏

Plug a 9 volt battery into the

battery clip.

❏

TOURNAMENT LOCK: Because the E-Trigger

board requires a tool to turn it on and off, no

tournament lock is necessary for competition paintball.

❏ ❏

❏

2). Install the E-Grip

Use a 7/16" ( )

wrench to loosen the gas

line nut

and then pull

the gas line

out of

the gas line elbow

❏

Check to be certain the trigger plates have not

separated and the E-Grip

trigger assembly is

intact as shown. If there are gaps at

between

the trigger plates

and the trigger or sear

- squeeze plates together to look as shown.

❏

Check to be certain the

trigger spring

is in

position as shown.

❏

Insert the gas line into the E-Grip

gas line elbow.

❏

Be careful that you do

not cross-thread the fitting

as you use your fingers to

align, start and finger

tighten the gas line nut

several turns onto the

gas line elbow

Complete tigntening with a 7/16" (

) wrench.

❏

To keep the battery from

rattling once it is in the E-Grip

turn the battery so the battery clip

wires

hang against the side

of the battery, then Insert the

battery into the E-Grip

as shown.

NOTE: When removing a battery

from the E-Grip

, Do Not pull

the battery out by the wires.

❏ ❏

❏

5) Re-install the battery door - Replace the

battery door with the tab down and listen for the

snap as it locks back into the E-Grip

The 3-position

safety/selector

switch

has

three settings:

S = Safe ;

F = Semi-Auto (One pull/release of the

trigger fires 1 time.

FA = Special Firing Mode. The Special Firing

Mode can be set to any 1 of 5 firing options as

detailed on page 2 -

Special Firing Mode Options

This E-Grip

is set to the factory default setting:

Safe Full-Auto - Pulling the trigger three times

in less than one second will result in full-

automatic firing. Holding the trigger down on

the third pull will sustain this full-auto mode. The

default rate of fire for this mode is 13 bps.

❏

then pull

the trigger and

❏

release

the handle

slowly

forward

to uncock the

marker.

NOTE: If pressing the

power button failed to

turn on the LED light,

see

Troubleshooting

Section

on page 2.

❏ ❏

❏

3) To fire the marker - select either the F or FA

position using the safety/selector switch and pull

the trigger. The LED will light orange with each

pull of the trigger.

❏ ❏

❏

4) Turn power off - To turn the power off, hold

the power button for 2 seconds. The LED will

change from green to red when the power-off

condition has been achieved. (NOTE: The trigger

electronics are set to shut-off automatically after

a prolonged period of inactivity (120 minutes).

❏ ❏

❏

5) Low battery condition -The E-Trigger

Low

Battery Indicator Feature: When the battery has

begun to lose power and needs replaced, the LED

will stop flashing green and begin flashing red.

While performance will vary while the LED is

flashing red, the E-Grip

will still function under

this condition until the battery has lost power to

the point that it will not cycle the marker.

❏ ❏

❏

6) Changing Special Firing Modes - To

change the Special Firing Mode - follow the

instructions in the Advanced User Programming

Section on page 2.

Summary of content (2 pages)

PAGE 1
TIPPMANN X7 E-GRIP KIT PART# T210001 INSTALLATION & PROGRAMMING INSTRUCTIONS KIT PN. T210001 NOTE: 9V Battery INCLUDES: Not Included, but Required ❏ 1 - X7 E-Grip ® TM TM TM STEP 2: Remove stock grip from marker. ❏ Do Not perform STEP 2 before reading the warning section and completing STEP 1. TM WARNING EYE PROTECTION DESIGNED FOR PAINTBALL USE MUST BE WORN AT ALL TIMES WHEN HANDLING THIS MARKER BY THE USER AND ANY PERSON WITHIN RANGE. DO NOT DISASSEMBLE THIS MARKER WHILE IT IS PRESSURIZED WITH AIR.
PAGE 2
Advanced User Programming Section There are several programming options which affect the operation of the Tippmann® X7TM E-GripTM. The Advanced User Programming has been designed to allow users the maximum amount of customization possible for their E-GripTM. There are four menu items in the Advanced User Programming: Dwell, DebounceTM, Rate-of-fire, and Special Firing Mode. Read and familiarize yourself with each of these items as they are explained in the following sections.