USER MANUAL t ip p ma n n .
WARNING This is not a toy. Misuse may cause serious injury or death. Eye, face, and ear protection designed for paintball must be worn by the user and any person within range. We recommend you be at least 18 years old to purchase. Persons under 18 must have adult supervision when using this product. Read the Owner’s Manual before using this product. WARNING Safety is Your Responsibility Read and familiarize yourself and any other user of this marker with the safety instructions in this manual.
RAIDER by Tippmann Sports/GI Sportz 2955 Adams Center Road. Fort Wayne, IN 46803 1-800-533-4831 • 1-260-749-6022 CONGRATULATIONS on your purchase of your Tippmann Raider paintball marker. We believe our Raider to be the most accurate and durable paintball marker available. Raider markers will provide many years of dependable service if cared for properly.
WARNING This product contains one or more chemicals that are known to the State of California to cause cancer and birth defects or other reproductive harm. Wash hands after handling. WARNING Always keep the barrel blocking device installed except when your marker is in use.
Warning/Liability Statement This marker is classified as a dangerous weapon and is surrendered by Tippmann Sports/GI Sportz/GI Sportz with the understanding that the purchaser assumes all liability resulting from unsafe handling or any action that constitutes a violation of any applicable laws or regulations.
• Do not shoot at fragile objects such as windows. • Never fire your marker at personal property of others. The paintball impact can cause damage and the paint can stain the finish of automobiles, houses, etc. • Always keep the muzzle pointed down or in a safe direction, even if you stumble or fall. • Eye, face, and ear protection designed specifically to stop paintballs in the form of goggles and full face mask meeting ASTM Specification F 1776 must be worn by the user and any person within range.
Getting Started • Eye protection designed for paintball use must be worn by the user and any person within range. • Do not disassemble this marker while it is pressurized. • Do not pressurize a partially assembled marker. • Read each step completely before performing the step. NOTE: Carefully hand start all threaded parts when assembling, and do not overtighten, as this may potentially strip the threaded parts.
4. Firing the Marker a. Point the marker in a safe direction. b. Remove the barrel blocking device from the marker. c. Move the Safety from safe mode to fire mode. d. Pull the trigger to fire the marker. Unloading Your Marker The barrel blocking device must be installed (see page 4) and the Safety in safe mode (see page 6). 1. Eye protection designed for paintball use must be worn by the user and any person within range. 2. Empty all paintballs from the Hopper. 3.
as shown in the bottom image, the cylinder is starting to 1 2 unscrew from the cylinder valve and you must STOP and take the entire unit to a “C5” certified airsmith for safe removal and/or repair. NOTE: The cylinder valve should unscrew from the paintball marker in about 3 or 4 full turns. If you finish the 4th full turn and the cylinder valve is not unscrewed from the paintball marker, STOP! Take the entire unit to a “C5” certified airsmith for safe 3 4 removal and/or repair.
NOTE: Locate a “C5” certified airsmith at www.paintball-pti.com. Air Cylinder Removal 1. Read Air Cylinder Warnings (page 8) and Air Cylinder Safety Tips (page 9-10) before beginning the cylinder removal process. 2. Eye protection designed for paintball use must be worn by the user and any person within range. 3. Follow the Unloading Your Marker instructions on page 8. 4. Watch the marks on the cylinder and cylinder valve as you turn the cylinder approximately ¾ turn counterclockwise.
To clean the exterior of your paintball marker, use a damp towel to wipe off paint, grease, and any debris. To clean the inside of the barrel, remove the barrel by unscrewing it from the Receiver. Insert the tab end of the cable squeegee into barrel. Pull the squeegee through the barrel to remove debris and paint. General maintenance on your marker should be performed every 8000-10,000 shots or before the start of each day of play, whichever comes first.
ITEM 1 2 3 4 5 6 7 8 DESCRIPTION ROLLER ASSY (COMPLETE) DRIVE SHAFT WITH GEAR QTY 1 1 SKU 74451 74452 CATCHCUP COVER CATCHCUP RAMP TOP RAMP MIDDLE RAMP BOTTOM DRIVE BUSHING 1 1 1 1 1 2 74453 74454 74455 9 10 11 12 13 PADDLE DRIVE WHEEL DRIVE CAM DRIVE ROD DRIVE ROLLER 1 1 1 1 1 38948 14 DRIVE PLUNGER 1 15 16 DRIVE ROD SPRING DRIVE PLUNGER SPRING 1 1 17 18 19 20 DRIVE ROD PIN DRIVE ROLLER PIN DRIVE SPRING SCREW BHCS 6-32 X .
Use the diagram above to disassemble and reassemble these main components of the Marker. The subassembly parts diagrams are on the following pages. Disassembly of Bolt System Remove loader assembly by removing two hex head screws. You can perform general maintenance like lubricating and replacing O-rings. Removal of Grip Frame and Regulator 1. Remove loader assembly. 2. Remove the 2 screws on the bottom of the ASA that hold the ASA in place.
ITEM 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 DESCRIPTION GRIP FRAME TRIGGER TRIGGER SPRING FRAME HEX INSERT FRAME SCREW INSERT SAFETY TRIGGER PIN O-RING BUNA-N 70 DUR 1.0MM 3.0MM ID BEARING BALL 2.0 MM DIA SAFETY SPRING NUT SQUARE 10-32 .375 WIDE X .125 THK SCREW BHCS 6-32 X .250 LOADER ADAPTER SCREW BHCS 10-32 X .875 SCREW BHCS 10-32 X 1.125 BRAIDED HOSE SCREW BHCS 10-32 X .
Advanced Regulator Disassembly and Maintenance Should your regulator have a leak or the pressure is not stable, causing velocity issues the following steps can be taken. WARNING: The below steps may be difficult for the novice paintball marker user and may require special tools. Damage to your regulator due to negligence may void your warranty. 1. First use expanding c-clip pliers to remove the larger retaining ring at the bottom of the regulator. The sleeve connected to the steel hose will now slide off.
diagram). This O-ring may stay located inside the regulator. Carefully use a pick to extract this O-ring. 3. If your regulator was causing velocity fluctuations and general maintenance didn’t help, you need to change the regulator seal adjuster (part 7 in regulator assembly diagram). Be sure when reassembling the regulator to follow the regulator assembly diagram. Assembling the regulator incorrectly will cause performance issues with the marker. Specifications Model........................................
Warranty Registration To activate the Marker’s Limited Warranty, you must register the Marker within thirty (30) days of the date of original retail sale by completing the attached warranty registration card and returning it to the address above. The Limited Warranty for Tippmann Accessories does not require activation or registration; by registering the Marker, you activate the warranty for the Accessories.
parts before returning the Marker for service or repair. 2. Always unload (page 10) and remove the air supply from the marker (page 14). Do not ship the air supply cylinder if it is not completely empty. 3. Ship the Product to the Tippmann address identified. 4. You must pre-pay postage and delivery charges. 5. Provide the date of purchase for the Product. 6. Briefly describe the repair requested. 7.
NOTES: t ip p m an n .
t ip p ma n n .
