User's Manual
E
N
G
L
I
S
H
8
• INSTALL THE AIR SUPPLY AND LOAD THE HOPPER WITH PAINTBALLS
ONLY AFTER YOU:
❏ ❏
❏ ❏
❏
HAVE THE BARREL BLOCKING DEVICE INSTALLED (SEE PAGE 2);
❏ ❏
❏ ❏
❏
HAVE THE TRIGGER SAFETY IN SAFE MODE (SEE PAGE 4);
❏ ❏
❏ ❏
❏
HAVE SUCCESSFULLY INSTALLED THE BATTERY ( STEP 1: PAGE 9) AND
❏ ❏
❏ ❏
❏
ARE FAMILIAR WITH THE E-GRIP NORMAL OPERATION (STEP 2: PAGE 9).
• EYE PROTECTION DESIGNED FOR PAINTBALL USE MUST BE WORN
BY THE USER AND ANY PERSON WITHIN RANGE.
WARNING
E-GRIP OPERATING INSTRUCTIONS
E-GRIP
TM
Operating Instructions
(continued on page 9)
To Install the battery:
❏
Remove the battery door from
the back of the E-Grip
TM
by pulling up and back on the tab .
NOTE: When removing the battery clip
from the battery,
Do Not pull it off by the wires
.
❏
Plug a 9 volt battery into the battery clip.
❏
Insert the battery into the E-Grip
TM
with the battery clip
at the top and wires as shown.
❏
Reinstall the battery door - Replace the battery door with
the tab
down, press the tab and listen for the snap as
it locks back into the E-Grip
TM
.
NOTE: The E-Grip
TM
Low Battery Indicator feature: the “Ready
To Fire” Flashing Green LED will turn to blinking red when
the battery is low and needs replaced (see -
Low Battery
Condition
on page 10).
S = Safe (as shown);
F = Semi-Auto
(One pull/release
of the trigger
fires 1 time).
FA = Special Firing Mode. The Special Firing Mode can be set to any 1
of 5 firing options as detailed in the Special Firing Mode section.
❏
Release the power button and the green LED will
begin flashing green to show the power is on and the
battery is good. (NOTE:
❏
If the LED begins flashing
red, see - Low Battery Condition on page 10).
1) To turn the E-Grip
TM
power on:
❏
Use a small object like an allen wrench ( )to
press and hold the power button
for 2 seconds.
The LED
will light orange then green when the
electronics have been activated.
2) Safety/Selector operation -
The 3-position safety/selector switch
has three settings:
3) To fire the marker -
❏ ❏
❏ ❏
❏
select either the F or FAposition using the safety/
selector switch and pull the trigger. The LED
will light orange with each
pull of the trigger.
4) Changing Special Firing Modes -
❏ ❏
❏ ❏
❏
To change the Special Firing Mode
while the E-Grip
TM
is powered on, press and hold the power button for a
1/2 second. The LED will flash orange to represent the number of the Special
STEP 2: Power On - Basic Operation
E-GRIP
TM
Operating Instructions
(continued on page 10)
9
STEP 1: E-GRIP
TM
Battery Installation or Replacement:
E-GRIP
TM
Operating Instructions (continued from page 8)
E
N
G
L
I
S
H
READ AND FOLLOW THE E-GRIP
TM
OPERATING INSTRUCTIONS (PAGES 8-
13) COMPLETELY BEFORE INSTALLING THE AIR SUPPLY CYLINDER AS
OUTLINED IN – GETTING STARTED - STEP 2: ON PAGE 6.
❏
If pressing the power button failed to turn on
the LED light, see Troubleshooting section on page 13.
• READ EACH STEP COMPLETELY BEFORE PERFORMING THE STEP:
2)
❏
Check that the Tombstone
Push Pin
is installed.
3)
❏
Check that the Tombstone
Latch
is set .
4)
❏
Check that Gas Line Adapter
and nipple fitting
are secure.
5)
❏
Pull and hold the Remote Coil
fitting Locking Ring
down to install
or remove the Remote Coil fitting
.
1)
❏
Remove the air supply from the marker Remote Coil as outlined in
the Air Supply Cylinder Removal instructions on pages 18-20. Never
disassemble a marker or remove a remote coil that is under pressure.
Remote Coil: Connecting and Disconnecting
NEVER INSTALL PRESSURIZED AIR TO THE MARKER WITHOUT THE
TOMBSTONE PUSH PIN INSTALLED AND THE TOMBSTONE LATCH
IS SET - HOLDING THE TOMBSTONE IN PLACE .
WARNING
6)
❏
With the Locking Ring held
down
, push the coil fitting
up onto the nipple and release
the locking ring up to lock
.
❏
To turn off air supply: turn flow control completely out
❏
To turn on air supply: turn flow control completely in
7)
❏
Pull down on the
Remote Coil fitting
to be sure it has locked properly.