User's Manual

❏❏
❏❏
❏ 1) Oil o-ring of the exterior flow control adapter .
❏❏
❏❏
❏ 2) Align threaded opening of interior flow connector
fitting
to inside of right receiver half.
❏❏
❏❏
❏ 3) Carefully thread adapter through the right
receiver half into
and tighten with a 3/8” wrench
(do not overtighten and strip threaded parts
or damage o-ring
).
27
E
N
G
L
I
S
H
26
4) Use your finger tips to guide the left half straight down on to the right half
Ball
Latch
3) With left hand holding as shown below,
use right hand to seat cocking handle with
spring into receiver cutout then position
edge of spring in end of spring cutout
bowed as shown below. Then grip left
receiver with right hand as shown.
Left
Hand
Right
Hand
Spring
Latch
Upper Receiver Assembly
1) Make sure all parts are clean before reassembling. Place right upper
receiver half flat with Tombstone Latch & Spring, Front Grip Nut, Receiver
O-ring and Ball Latch in position as shown below.
Cocking Handle Spring
will be
bowed.
WARNING
DO NOT REASSEMBLE WITHOUT MAKING SURE
TOMBSTONE LATCH & SPRING ARE PROPERLY
INSERTED IN PLACE AS SHOWN.
Cocking Handle
Front Grip Nut
with flat side facing
bottom of marker.
Tombstone
Latch & Spring
properly inserted
Left
Half
Right
Half
E
N
G
L
I
S
H
until receiver halves fit flush. If it does not fit flush the first time, check to
make sure the spring and other parts have stayed in place and repeat until
halves fit flush.
5) Insert 5 (4 on Response
TM
Marker) Receiver Bolts (not front sight
bolt yet) & tighten them just enough to hold halves flush yet loose enough
to allow you to now insert and twist Barrel / Adapter unit (or FLATLINE
TM
)
clockwise
to reinstall.
6) Insert Front Sight with its slot facing back of marker, into the top front
of the receiver and insert the front sight bolt to hold in place.
7) Make sure all receiver bolts are tight (do not overtighten & strip threads).
Upper Receiver Assembly
(continued on page 27)
Upper Receiver Assembly (continued from page 26)
B
C
4) ❏ While keeping cap screw and front sight aligned, tighten the
3 receiver screws A,B&C
to complete the installation.
Cap
screw
to the
left
Properly installed barrel will look like this.
Proper
screw
position
Proper screw position
1) ❏ Loosen 3
receiver bolts
(A, B, & C).
2)
❏ Position the Barrel
Adapter cap screw
facing to the left toward
the feeder housing and
insert into receiver.
A
B
Feeder
Housing
A
Flatline
TM
Barrel Installation:
3)
❏ Turn the Barrel
Assembly 1/4 turn to the
right until the adapter
cap screw aligns with
the front sight.
Front
Sight
Cap
Screw
C
FLATLINE
TM
Barrel Removal & Installation
❏ First follow ❏ Unloading Your Marker and ❏ Air Supply Cylinder
Removal instructions on pages 18-20. Never disassemble a marker
that is under pressure or pressurize a partially assembled marker.
Flatline
TM
Barrel Removal:
❏ Loosen 3 receiver bolts (A,B&C-seebelow) then turn barrel /
adapter to left and remove as one piece from upper receiver.
Barrel at top
2) With left hand, grip left upper
receiver half as shown to hold
Cocking Handle and spring in place
by applying side pressure with
index finger pushing in direction of
arrows
against Cocking Handle.
For Response
TM
Marker only: Install two parts & to the right receiver
half before assembling receiver halves.
Receiver O-ring
3) ❏ Remove the 5 receiver bolts (4
on Response
TM
Marker) holding the upper
receiver halves together.
❏ To reassemble upper receiver follow the
Upper Receiver Assembly instructions below.
Upper Receiver Disassembly: (continued from page 25)