User's Manual

ManualsBrandsTippmann ManualsPaintballTippmann A5 Marker

❏

Line up the lower receiver front push pin holes

with the upper receiver holes then gently rock

rear of grip until you can insert the two lower

receiver push pins

& to attach.

❏

Check to becertain the

trigger plates have not

separated and thetrigger

assembly is intact as

shown. If there are gaps

(On the A-5

Response

marker,

❏

first put a

couple drops of marker oil onto the cylinderfitting

o-ring

in the lower receiver.)

❏ ❏

❏

To attach the lower receiver (grip) to the upper receiver:

❏

Attach the Tank Adapter: Slide tank adapter into lower receiver

and align holes;

❏

Insert receiver bolt and tighten ( on A-5

E-Grip

position the tank adapter and insert the 2 tank adapter bolts and

(the short adapter bolt goes in front - see page 23).

TA99500

Electronics Assembly

A-5

E-Grip

Model Specific

Parts: Not Shown on A-5

Basic Parts List on pages 16-17.

TA01018

Lower

Receiver

Left

TA01019

Lower Receiver Right

NOTE: A-5

E-Grip

Sear Spring 02-88 has tensions specifically designed for the E-

Grip

and it will not operate properly if you replace this spring with any other spring.

TA10073 Sear

02-88

Sear

Spring

(silver - long)

02-20S

Trigger

Spring

(Red-short)

TA10021

Trigger

TA10072 Magnet

(the red dot on the magnet must be

visible on this side of the trigger to

operate properly).

02-33A

Sear Pin

(black)

02-33 Pins (4)

02-67R

Right

Trigger

Plate

TA02061 Tank Adapter

Frame

Half - Left

TA10066

Battery Door

Electronics

board

Spacer

Armature

E-Grip

parts shown in position in

the Right Trigger Plate with basic

parts (Note: E-Grip

Specific parts

in bold).

Frame Half - Right

CA-08B

Adapter

Nut (2)

E-Grip

Electronics

Assembled ;

trigger guard

and 2 adapter

nuts - shown

positioned in the right

grip half for reassembly

of the E-Grip

- see above.

TA07074

AdapterBolt

(short)

02-67L Left Trigger Plate

Double Trigger Kit (Optional, not included with A-5

E-Grip

Marker):

Installation: The trigger slider & spring will need to be

removed from the double trigger before installation into the E-

Grip

. Remove pins and from the double trigger and

remove the trigger slider & spring.

NOTE: If the double trigger kit does not include a magnet -

take the magnet from the single trigger that came with your

marker and insert the magnet at

(the red dot on the magnet

must be visible (see above) to operate properly.

TA01022

Safety

Selector

98-01B

Adapter Bolt (long)

❏

Replace left grip half .

❏

Secure grip halves with 3 grip screws .

❏

Reinstall the battery door on A-5

E-Grip

(see instructions - page 9).

❏

Reinstall the trigger assembly into the grip and insert the safety

into the left side of the grip (on E-Grip

marker:

❏

Rotate the Safety

Selector Switch

straight up and

❏

insert it into the left side of the

grip and then rotate it to the “SAFE” =

position).

❏❏

❏

To disassemble the upper receiver : NOTE: It is only necessary to

disassemble upper receiver halves to access the ball latch, front grip nut, cocking

handle, cocking handle spring, receiver o-ring, Tombstone latch and Tombstone

latch spring (plus the flow connector fitting on A-5

Response

Marker).

❏

1) Follow the Marker/Receiver Disassembly/Assembly instructions beginning

on page 21 until you have removed the drive assembly parts on page 22.

between the trigger plates and the trigger or the sear –

squeeze the plates together to look as shown.

Lower Receiver Disassembly/Assembly: (continued from page 24)To reassemble the lower receiver: (continued from page 23)

Lower Receiver Disassembly/Assembly:

(continued on page 25)

Upper Receiver Disassembly:

(continued on page 26)

❏

2) Remove the Cyclone

Feed System:

❏

Remove the

banjo fitting

bolt

from

upper receiver

(and on Response

marker -

remove the flow control

adjustor fitting and banjo fitting bolt from the upper receiver - see

Response

parts on page 14).

❏

Remove the Cyclone

housing bolt

from the left front side of upper receiver and remove the feed system

(NOTE: To install the Cyclone

Feed System reverse the process).

❏

On A-5

E-Grip

: make sure trigger guard , 2 adapter nuts , and

E-Grip

assembly (with armature spacer and armature in place

); are positioned in the right grip half as shown below. Position wires

around the posts

as shown so wires are not pinched or sheared when

the left grip half is replaced. Visually inspect wires for damage or

disconnected wire ends at