Manual

21
E
N
G
L
I
S
H
20
a) Insert the Flow
Connector Bolt
into receiver as
shown.
b) Place the Connector
Fitting (largest
opening first)
onto the Connector
Bolt as shown.
4) Use your finger tips to guide the left half straight down on to
right half until receiver halves fit flush. If it does not fit flush the
first time, check to make sure the spring and other parts have
stayed in place and repeat until halves fit flush.
Ball
Latch
3) With left hand holding as
shown below, use right hand to
seat cocking handle with spring
into receiver cutout then position
edge of spring in end of spring
cutout bowed as shown below.
Then grip left receiver with right
hand as shown.
Left
Hand
Right
Hand
Spring
Latch
Upper Receiver Assembly
How to reinsert upper receiver internal parts and put two
upper receiver halves together.
2) With left hand, grip left
upper receiver half as
shown to hold Cocking
Handle and spring in place
by applying side pressure
with index finger pushing in
direction of arrows against
Cocking Handle.
1) Make sure all parts are clean before reassembling. Place
right upper receiver half flat with Tombstone Latch & Spring,
Front Grip Nut, and Ball Latch in position as shown below.
Cocking Handle Spring
will be
bowed.
WARNING
DO NOT REASSEMBLE WITHOUT MAKING SURE
TOMBSTONE LATCH & SPRING ARE PROPERLY
INSERTED IN PLACE AS SHOWN.
Cocking Handle
Front Grip Nut
with flat side facing
bottom of marker.
Tombstone
Latch & Spring
properly inserted
a) & b) For Response
TM
& CR-15
TM
Markers only: You must next
place two parts a & b on
left receiver half before assembling
receiver halves.
a
b
Left
Half
Right
Half
c
E
N
G
L
I
S
H
5) Insert 5 (4 on Response
TM
& CR-15
TM
Markers) Receiver Bolts
(not front sight bolt yet) & tighten them just enough to hold halves
flush yet loose enough to allow you to now insert and twist Barrel
/ Adapter unit (or FLATLINE
TM
) clockwise to reinstall.
6) Insert Front Sight with its slot facing back of marker into
the top front of receiver and insert 6th (5th on Response
TM
&
CR-15
TM
Markers) bolt to hold in place.
7) Make sure all bolts are tight (do not overtighten / strip threads).
8) For A-5
TM
Response
TM
& CR-15
TM
Markers Only: Place Flow
Connector Nut (c) onto Flow Connector Bolt (a) and tighten.
Upper Receiver Assembly (continued on page 21)
Upper Receiver Assembly (continued from page 20)
B
C
Step 5: While keeping screw and front sight aligned, tighten
the 3 receiver screws A, B & C
to complete the installation.
Cap
screw to
the left
Properly installed barrel will look like this.
Proper
screw
position
Proper screw position
Step 2: Loosen
3 receiver bolts
(A, B, & C).
Step 3: Position
Barrel Adapter cap
screw facing the
left toward feeder
housing and insert
into receiver.
A
B
Feeder
Housing
A
Flatline
TM
Barrel Installation Step 1: First follow unloading
and air supply removal instructions on page 16 and never
disassemble a marker that is under pressure.
Step 4: Turn Barrel
Assembly 1/4 turn to the
right until the adapter
cap screw aligns with
the front sight.
Front
Sight
Cap
Screw
C
FLATLINE
TM
Barrel Removal & Installation
Flatline
TM
Barrel Removal Step 1: First follow unloading and
air supply removal instructions on page 16 and never
disassemble a marker that is under pressure.
Step 2: Loosen 3 receiver bolts (A, B & C - see below) then
turn barrel / adapter to left and remove as one piece from
upper receiver.
Barrel at top