Manual

E
N
G
L
I
S
H
E
N
G
L
I
S
H
STEP 1) Prepare Marker for Air Supply Cylinder Installation
• For markers with E-Trigger
TM
- You must first read and follow E-Trigger
Operating Instructions (on pages 7-12) before performing
STEP 2.
• For markers without E-Trigger
TM
go to STEP 2.
STEP 2) Air Supply Cylinder Installation
• Do not pressurize a partially assembled paintball marker.
• First install barrel sleeve (see instructions on page 2).
• Next put trigger safety in Safe Mode
(see instructions on page 4).
6
Getting Started (continued on page 7)
STEP 3) Hopper Installation
• Barrel Sleeve must be installed (see page 2) and safety in Safe Mode (see
page 4) before filling the hopper.
• Make sure that the feed elbow and hopper are clean and free of any sharp
edges to keep paintballs feeding into the marker smoothly.
• Install the hopper neck into the feed elbow of your marker and tighten the
hopper down with a 3/16” allen wrench.
NOTE: Do not overtighten or the elbow may break. With the barrel sleeve
installed and safety in Safe Mode, you are now ready to load your hopper
with paintballs. Fill the hopper and only remove barrel sleeve and turn off
the safety when ready to shoot.
GETTING STARTED
❏ Eye protection designed for paintball use must be worn by the user and
any person within range. Do not disassemble this marker while it is
pressurized with air. Do not pressurize a partially assembled marker.
Read each step completely before performing the step.
NOTE: Carefully hand start all threaded parts and do not overtighten and
strip threaded parts when assembling.
• Next you need to cock the marker
by sliding the bolt handle
all the way
back until it locks into place. Always
keep marker in the cocked position when
air supply is attached to the marker. This
will help prevent an accidental discharge.
• To install the air supply cylinder, lubricate the cylinder valve o-ring with
a little marker oil then insert the cylinder valve end into the air supply
adapter at the back end of the marker grip. Turn the cylinder clockwise
into the marker until it stops. Your marker is ready to fire once you
switch to Fire Mode from Safe Mode. If the tank is full and you do not
hear the air supply engage, the pin valve could be too short or the pin
valve seal is damaged.
7
Getting Started (continued from page 6)
STEP 4) Rate of Fire Adjustments and Troubleshooting
• For RESPONSE
TM
markers - complete Tuning The Response Trigger Rate
of Fire instructions (on page 13) before performing
STEP 5.
• For E-TRIGGER
TM
markers - read and follow E-Trigger
TM
Operating Instructions
(on pages 7-12); before performing
STEP 5.
• For Basic Non-A.C.T., Basic A.C.T. and Pro
TM
markers - Go to STEP 5.
Velocity
Adjustment
Screw
STEP 5) Velocity Adjustment
Each time you play paintball, the
velocity of your paintball marker should
be checked with a chronograph, an
instrument for measuring velocity, prior
to playing paintball to verify that the
marker’s velocity is set below 300 feet
per second or less if required by
playing field.
To adjust the velocity use the 5/32” allen wrench included with your marker.
The velocity adjustment screw is located on left side receiver. To adjust the
velocity down, turn the screw inward or clockwise
. To turn the velocity
up, turn the screw out or counterclockwise
. Do not remove velocity screw.
INSTALL THE AIR SUPPLY AND LOAD THE HOPPER WITH PAINTBALLS
ONLY AFTER YOU:
❏ ❏
❏ ❏
❏ HAVE THE BARREL SLEEVE INSTALLED (SEE PAGE 2);
❏ ❏
❏ ❏
❏ HAVE THE SAFETY IN THE "SAFE" POSITION (SEE PAGE 4);
❏ ❏
❏ ❏
❏ HAVE SUCCESSFULLY INSTALLED THE BATTERY (STEP 2: - PAGE 8) AND
❏ ❏
❏ ❏
❏ ARE FAMILIAR WITH THE E-TRIGGER
TM
NORMAL OPERATION (STEP 3:
- PAGE 8).
WARNING
READ EACH STEP COMPLETELY BEFORE PERFORMING THE STEP:
Prepare the marker for disassembly. First follow ❏ Unloading Your
Marker and
❏ Air Supply Cylinder Removal instructions on page
20. Do not disassemble this marker while it is pressurized with air.
Do not pressurize a partially assembled marker.
Read And Follow E-Trigger
TM
Operating Instructions completely (on
pages 7-12) before installing the air supply cylinder as outlined in -
Getting Started -
STEP 2: on page 6.
❏ Eye protection designed for paintball use must be worn by the user and
any person within range.
E-TRIGGER
TM
OPERATING INSTRUCTIONS
(continued on page 8)
E-TRIGGER
TM
OPERATING INSTRUCTIONS
STEP 1: Prepare the marker for safety before any programming:
5/32”Allen
Wrench