User manual
D
DEUTSCH
Angaben gemäß der Richtlinie EIA RS485.
HILfSSpaNNUNG
Nennspannung: 230 V
AC
±20% / 50 Hz
Max Wiederholspannung: 300 V
AC
Max nicht Wiederholspannung Spitzenwert: 320 V
AC
(20 ms)
Verbrauch: max 5 VA
Vorsicherung: Typ T, 100 mA (extern zu installieren)
RS485 KOMMUNIKaTION
Protokoll: MODBUS RTU (8N1) und ASCII (7E2)
Schnittstelle: RS485
Kommunikationsgeschwindigkeit: 300...115200 bps
Terminationswiederstan im Modul eingebaut: 120 Ohm
BUSLINIE
Typ: Infrarot-Schnittstelle
Kommunikationsgeschwindigkeit: 38400 bps
KONfORMITÄTSERKLÄRUNG
EN61000-6-2 Störfestigkeit (Industriebereich):
EN61000-4-2 Elektromagnetische Verträglichkeit, EN61000-4-3 Abgestrahlte RF Störung,
EN61000-4-4 schnelle Transienten (Burst), EN61000-4-5 Stoßspannungen (Surge),
EN61000-4-6 leitungsgeführte RF-Signale, EN61000-4-11 Spannungseinbrüche am AC Hilfspannung
EN55011 Klasse A: Angestrahlte und Ausgeführte Ausstoß
Sicherheitsbestinnungen: EN60950
aNSCHLIESSBaRER LEITER
Klemmen: 0,14...2,5 mm
2
UMWELTBEDIENGUNGEN
Arbeitstemperaturbereich: zwischen -15°C und +60°C
Lagertemperaturbereich: zwischen -25°C und +75°C
Relative Luftfeuchte: 80% max ohne Kondensation
Schutzgrad: IP20
GB
ENGLISH
Data in compliance with EIA RS485 standard.
pOWER SUppLY
Rated voltage: 230 V
AC
±20% / 50 Hz
Max repetitive voltage: 300 V
AC
Max non repetitive voltage peak: 320 V
AC
(20 ms)
Consumption: max 5 VA
Fuse: T type, 100 mA (to be mounted externally)
RS485 COMMUNICaTION
Protocol: MODBUS RTU (8N1) and ASCII (7E2)
Port: RS485
Communication speed: 300...115200 bps
Termination resistor (RT) integrated in the module: 120 Ohm
SERIaL COMMUNICaTION
Type: optical port
Communication speed: 38400 bps
STaNDaRDS COMpLIaNCE
EN61000-6-2 Immunity for industrial environments:
EN61000-4-2 Electrostatic discharge, EN61000-4-3 RF radiated disturbance,
EN61000-4-4 Fast Transient (BURST), EN61000-4-5 Overvoltage (Surge),
EN61000-4-6 RF conducted disturbance, EN61000-4-11 Voltage dips and short interruptions,
EN55011 Class A: radiated emissions, conducted emissions
Safety: EN60950
WIRE DIaMETER fOR CONNECTION TERMINaLS
Terminals: 0.14...2.5 mm
2
ENvIRONMENTaL CONDITIONS
Operating temperature: between -15°C and +60°C
Storage temperature: between -25°C and +75°C
Humidity: 80% max without condensation
Protection degree: IP20
TECHNISCHE EIGENSHAFTEN
TECHNICAL FEATURES
VERDRAHTUNG
CONNECTIONS
230 V
AC
BRÜCKE ZUM RT EINSCHALTEN
JUMPER FOR RT ENABLING
+
-
COM
D
DEUTSCH
Zwischen PC und RS485 Netzwerk ist ein Schnittstellenwandler zur Anpassung der RS232/
USB zum Netzwerk erfordert. Wenn die anzuschlissenden Module mehr als 32 sind, ist ein
Signalrepeater erfordert. Jeder repeter kann bis 32 Geräte verwalten.
Der im Abbild angezeigten Anschluss verfügt über einen dritten Leiter an der Klemme,
der das selben Bezugniveau an allen Geräten auf den Netwerk gewährleistet. Bei staken
elektromagnetischen Störungen , die die Kommunikation beeinträgtigen können, wird die
Anwendung ein zwei geschildeten gedrehten Leiterkabel empfohlen. Das Modul ist mit einem
Terminationswiederstand (RT) ausgestattet, der beim Brücken der entsprecheden Klemmen
eingeschaltet wird. Ein Terminationswiderstamd am PC einbauen, und auf das letze an der Linie
angeschlossenen Modul einschalten.
Die maximal empfohlene Länge der Drahte ist 1200 m mit 9600bps. Für längere Netwerke ist es
ratsam, einen niedrigeren Baudrate, Kabel mit gerimgerem Dämpfung oder Signalrepeater.
Nachdem das Netwerk verdraht worden ist, jedes RS485 Modul mit den ensprechendem Zähler
ankoppeln: die zwei nähern und einreihen, damit die Infrarot-Schnittstelle gegenüber stehen.
Die Modbus Protkollbeschreibung ist in dem beiliegendem CD verfügbar. Die RS485 Parameter
können sowohl am angeschlossenen Zähler als auch beim Versenden der entsprecheden
MODBUS Befehle verändert werden.
GB
ENGLISH
A serial converter is required between PC and the RS485 network to adapt RS232/USB port
to network. If there are more than 32 modules to be connected, insert a signal repeater. Each
repeater can manage up to 32 modules. For the connection among the different modules, use a
cable with a twisted pair and a third wire. The type of connection shown in the picture uses the
third conductor to ensure that all the devices on the network have the same reference level and
improve the reliability of communication. When there are strong electromagnetic disturbances,
which may affect communication, a shielded cable should be used. The module is integrated
with a termination resistor (RT) which can be enabled by jumpering the relevant terminals. The
termination resistance must be installed on the PC and enabled on the last module connected
along the line. Thanks to these resistances, the reflected signal along the line is reduced.
The maximum recommended distance for a connection is 1200 m at 9600 bps. For longer
distances, lower baud rates or low-attenuation cables or signal repeaters are needed.
After making RS485 connections, combine each RS485 module with a single counter: place them
side by side, perfectly lined up, with module optical port facing the counter optical port.
MODBUS protocol is available on the enclosed CD. RS485 parameters can be changed directly on
the combined counter or by sending the proper MODBUS protocol commands to the module.
WANDLER
CONVERTER
RS232/USB
REPEATER
REPEATER
max 32 Module
max 32 modules
WANDLER
CONVERTER
RS232/USB
COM
-
+
COM
- +
COM
- +
RT
RT AUF DAS LETZTE AN DER LINIE
ANGESCHLOSSENE MODUL EINSCHALTEN
ENABLE RT ON THE LAST MODULE
CONNECTED TO THE LINE