Cat No.
ZV700 – Lower Flap Closed Rocker switch – used in manual operation Supply ON LED 1 Photocell window Lower flap hinges open – see page 2 1. General The ZV700 combines the function of a manual lightswitch with automatic timed control of lighting on a weekly basis available at the slide of a switch. There is a further option of starting an automatic lighting period at dusk but ending it in the usual way with a timed “OFF”.
ZV700 – Lower Flap Open Override button – also used in conjunction with the programme button to set the clock and ON/ OFF times, days and random facility.
Important Installation Instructions IF IN DOUBT CONSULT AN ELECTRICIAN. Switch off mains electricity Remove the existing light switch and transfer the wires to the security switch according to the following instructions. 3 If the switch is an ON/OFF two wire type, those wires should be inserted into the terminals marked L1 and COM. Do not disturb any earthing wire connected to the wallbox terminal. If the switch is a 2-WAY switch, used in conjunction with a second light switch, it will have 3 wires.
2. Commissioning 4 After having installed the unit in accordance with the installation and wiring instructions on the back of the blister card, move the slide switch to the AUTO & PHOTOCELL position (this is important because the unit always powers up in this mode regardless of switch position), and switch ON the supply to the unit. The LED should now light up, if it does not then either the supply is not present or all the lamp(s) under control are not present or faulty.
5. Operation in AUTO & PHOTOCELL Mode Move the slide switch to the AUTO & PHOTOCELL position and turn the rocker switch ON. In this mode the unit will turn ON at dusk and OFF at a time programmed by the user. To do this it needs an ON time prior to dusk to be programmed by the user along with the above OFF time (see Programming Instructions). A safe ON time to cover the whole year anywhere in the U.K. is 1400 hours. A additional ON period can be programmed for the early morning if required.
Only two setting buttons are required, and . The button is guarded to minimise inadvertent programme change. In normal operating mode the button is used to switch ON or OFF, overriding the timeswitch until the next programmed OFF or ON time. During programming the button is used to set the hours, minutes and days. The button is used to select the clock time and day or the 6 programmed ON/OFF times and days and to review them once they have been set.
Programming sequence Setting clock Programme 1 ON Programme 1 OFF Programme 2 ON Programme 2 OFF Programme 3 ON Programme 3 OFF Programme 4 ON Programme 4 OFF Programme 5 ON Programme 5 OFF Programme 6 ON Programme 6 OFF Operation Mode Note: Pauses between button presses greater than 1 minute during programming will result in automatic return to the operating mode. 10. Setting Clock (after reset) Day Setting – Press button to advance to the day required. Day 1 = Monday and Day 7 = Sunday.
11To Set Programme ON/OFF Times (after clock setting) It must be remembered that the unit has a total of six programmes. i The user is now able to set the day(s) that the first programme will operate on.
vi Repeat steps i to v to set the remainder of the 5 programme ON/OFF times and day(s) as required. Note: Any unused ON/OFF programmes must be left blank and should be skipped by pressing the button until the display shows normal operating mode. Do not programme ‘0’s into unused programmes. IMPORTANT After setting a clock time which falls within a programmed ON period, the unit will not switch ON. Press the button to switch the unit ON.
15 Programming Across Midnight This can be achieved by programming the required ON time in the initial day and the required OFF time in the subsequent day. The unused times in these two programmes can either be left blank (--:--) or used for an OFF time during the initial day and an ON time during the subsequent day. 16 Self Cancelling Override To change the output status from ON to OFF or vice versa press the button.
3 Year Guarantee In the unlikely event of this product becoming faulty, due to defective material or manufacture, within 3 years of the date of purchase, please return it to your supplier with proof of purchase and it will be replaced free of charge. Should you encounter any difficulty please contact our helpline on 0845 3554504 For assistance with the product please contact: HELPLINE 020 8450 0515 or email helpline@timeguard.com For a product brochure please contact: 67.058.500 (issue 2).
