SLW360_Instruct_art_2.1.qxd 3/5/06 9:28 am Cat No.
SLW360_Instruct_art_2.1.qxd 3/5/06 9:28 am Page 1 Introduction A Side View B 2.5m More sensitive 1 The SLW360 utilises passive infrared technology to detect heat radiation of moving human bodies.Upon detection, the attached lighting load will illuminate for a user-determined time period. An integral daylight sensor ensures day or night-only operation.
SLW360_Instruct_art_2.1.
SLW360_Instruct_art_2.1.qxd 3/5/06 9:28 am Page 3 Parts included • PIR Sensor unit. • Instruction manual. Please keep safe for future reference. • Accessory Pack. Includes 2 x wall plugs, 2 x wall fixing screws, 1 x lens mask sticker. • 1 x outdoor mounting sealing gasket. • 1 x incoming/outgoing wire gasket. Tools and parts needed • 3 core flexible cable. • Electric/hand-held drill & bits. • Terminal or Electricians screwdriver. • Large slotted/philips screwdriver.
SLW360_Instruct_art_2.1.qxd 3/5/06 9:28 am Page 4 The sensor is more sensitive to movement ACROSS its field of vision than to movement directly TOWARDS (see diagram B). Therefore position the unit so that the sensor looks ACROSS the likely approach path. Avoid positioning the sensor where there are any sources of heat in the detection area (extractor fans, tumble dryer exhausts etc.) including opposite any other light sources such as other security lights.
SLW360_Instruct_art_2.1.qxd 3/5/06 9:28 am Page 5 PIERCE & PASS THE INCOMING AND OUTGOING CABLE THROUGH THE GROMMET BEFORE SECURING CEILING MOUNTING PLATE TO CEILING. It is recommended that the grommet is pierced with a screwdriver to ensure a better seal. Connection 5 THERE ARE 2 POSSIBLE CONNECTION SCENARIOS 1. Standard connection. See Diagram G. The factory fitted “bridge” wire must not be removed.
SLW360_Instruct_art_2.1.qxd 3/5/06 9:28 am Page 6 See diagram “I” for ceiling mounting assembly method. Fit the sensor assembly to the ceiling, if mounting outdoors, it is essential that the sponge gasket is placed between the ceiling mounting plate and the sensor itself to ensure a good seal is maintained. If mounting the unit indoors, the gasket is not required and can be discarded. Insert fixing screws through the sensor assembly into the wall plugs and secure.
SLW360_Instruct_art_2.1.qxd 3/5/06 9:28 am Page 8 Start moving again. As you cross each "zone" the lamp will illuminate. Repeat the above, walking at various distances and angles to the unit. This will help you to establish the detection pattern. Masking the Sensor Lens To reduce the sensor coverage, preventing detection in unwanted areas, mask the sensor lens using the lens mask sticker supplied (see diagram D).
SLW360_Instruct_art_2.1.qxd 3/5/06 9:28 am Page 9 At this position, the unit should become operative at approximately the same level of darkness each evening. Observe the operation of the unit. If the unit is starting to operate too early (ie. when it is quite light), adjust the control slightly anti-clockwise. If the unit starts to operate too late (ie. dusk), adjust the control slightly clockwise. Continue to adjust until the unit operates as desired.
SLW360_Instruct_art_2.1.qxd 3/5/06 9:28 am Page 10 Troubleshooting guide 9 Problem • Lamp stays ON all the time at night. Solution Cover PIR lens with a thick cloth. If the light turns out, check detection area for heat or reflective source. If the light stays on, check wiring. See Section 3. • PIR keeps activating for no reason (at random). Turn off at the internal wall switch. Leave for 30 seconds and turn on again. Leave for at least 18 minutes.
SLW360_Instruct_art_2.1.qxd Problem • Detection range varies from day to day 3/5/06 9:28 am Page 11 Solution PIR detectors are influenced by climatic conditions. The colder the ambient temperature, the more effective the sensor will be. You may need to make seasonal adjustments to the detector head position to ensure trouble-free operation all year round. Technical specifications 10 Detection Range: Up to 6 metres diameter (3m Radius) at mounting height of 2.
SLW360_Instruct_art_2.1.qxd 3/5/06 9:28 am Page 7 3 Year Guarantee In the unlikely event of this product becoming faulty due to defective material or manufacture within 3 years of the date of purchase, please return it to your supplier in the first year with proof of purchase and it will be replaced free of charge. For the second and third years or any difficulty in the first year telephone the helpline on 020 8450 0515.
