Model: LED100PIRWH - White Model: LED100PIRB - Black Installation & Operating Instructions Single Spot 8W LED Lighting with Motion Detection Sensor
1. Designated Use • LED100PIR is an outdoor motion detector for automatic LED lighting control. • Suitable for installation on walls. • Simple plug in wall plate for easy & safe connection. • Suitable for a wide range of locations: corridors, gardens, staircases, entrances, garages, outdoor parking areas etc. 2. Basic Safety Instruction Danger of death through electric shock. • Must only be installed by qualifi ed electricians. • Avoid the metal parts of the device due to potentially high temperature.
. Contents: Whats in the box? x2 x2 x1 x1 x1 2 4. Tools Required: Tools/equipment needed for installation.
5. Product Dimensions: 22.00 81.00 75.00 182.80 3 80.00 47.50 61.
6. Installation Procedure: Switch off the power. Twist-open the wall plate. 240V OFF Fix the wall plate to the wall. Ø5mm L N Mounting Screws x2 60mm 4 Feed the wires through rubber gasket of the wall plate and attach to corresponding terminal. Attach the device to the wall plate. L N L LIVE BROWN N NEUTRAL BLUE GREEN/ EARTH YELLOW Switch On the power. 240V ON Unit goes into warm-up period for 40 sec.
Installation Advise: As the detector responds to changes in temperature, avoid the following situation: • Pointing the detector towards objects with highly reflective surfaces, such as mirrors etc. • Mounting the detector near heat sources, such as heating vents, air conditioning units, lights etc. • Pointing the detector towards objects that may move in the wind, such as curtains, tall plants etc. ºC ºC ºC 40 40 40 5 Detection Range: LED100PIR: Recommended installation height is 2.
Walk Test and Adjustment The purpose of Walk Test is used to test and adjust the detection coverage of LED100PIR under auto mode. • Adjust the Time knob to “T”, then conduct a walk test as described in test procedure. Test procedure: • Adjust the Time knob to “T”, (Lux knob can be “Sun” or Moon”). • Switch power On. • Walk across the detection area, once the detector is triggered and the lamp will turn On for 2 seconds. Note walking direction when performing test.
Knob Settings LED100PIR has two adjustment knobs: Time and Lux at the bottom of the detector head. • Adjust knobs carefully with hand. TIME knob setting • You can set the time knob from 5 sec to about 10 min, LED100PIR will turn On the lamp, for the time duration set after each detected movement. • Adjust the knob as desired. LUX knob setting • When setting the Lux knob at “MOON”, LED100PIR Single will only operate in the dark. • When setting the Lux knob at “SUN”, LED100PIR will operate in any light level.
Lamp turns On at night. Lamp turns On at day & night. Setting Advise Lens masking 8 The purpose of the lens mask is to mask out areas not desired for detection. Lens mask fitting procedure: • Use a penknife or pliers to cut out lens mask segment, exposing area for detection. • Attach the lens mask to the detector head. • Turn slightly the lens mask for it to be locked into place.
Lamp Adjustment The lamp can be tilted down 85 deg. and pan outwardly 40 deg. 40º 9 85º High Temperature The temperature of the lamp is very high during operating. You will get hurt, if you touch the heat sink.
3 Year Guarantee In the unlikely event of this product becoming faulty due to defective material or manufacture within 3 years of the date of purchase, please return it to your supplier in the first year with proof of purchase and it will be replaced free of charge. For years 2 and 3 or any difficulty in the first year telephone the helpline on 020 8450 0515.
HELPLINE 020 8450 0515 or email helpline@timeguard.com For a product brochure please contact: Designed in the U.K. 67-058-417 Zerofour – August 2011 Timeguard Limited. Victory Park, 400 Edgware Road, London NW2 6ND Sales Office: 020 8452 1112 or email csc@timeguard.
