Instructions / Assembly

ManualsBrandsTie Down ManualsBuilding materialsTranzSporter 250-lb Capacity Platform Hoist with Lifan Gas Engine 28ft

404-344-0000 • www.tiedown.com

605 Stonehill Drive SW, Atlanta, GA 30336

sales@tiedown.com

Safety Instructions for the

TP250/400 Lift Hoist

General Safety Instructions:

In order to set up and operate the TranzSporter ladder hoist safely in and

around ELECTRIC POWER LINES and be compliant with OSHA Regulations

1926.416(a), the following must be ascertained prior to setting up the

TranzSporter each time for the protection of employees.

1926.416 (a)(1): No employer shall permit an employee to work in such proximity to any part of an

electric power circuit that the employee could contact the electric power circuit in the course of work, unless the

employee is protected against electric shock by deenergizing the circuit and grounding it or

by guarding it efﬁciently by insulation or other means.

1926.416 (a)(3): Before work is begun the employer shall ascertain by inquiry or direct observation, or by instruments,

whether any part of an energized electric power circuit, exposed or concealed, is so located that the performance of

the work may bring any person, tool, or machine into physical or electrical contact with the electric power circuit.

The employer shall post and maintain proper warning signs where such a circuit exists. The employer shall advise

employees of the location of such lines, the hards involved, and the protection to be taken.

General Safety Instructions:

1. Unpack the TranzSporter carefully and inspect for any damage that may occur during transportation.

DO NOT USE THE HOIST IF ANY PART IS DAMAGED.

2. Please observe all safety and warning labels attached to the hoist.

3. Always keep the area around the base section of the TranzSporter Hoist clear to help prevent slipping,

tripping or falling against the hoist.

4. DO NOT ALLOW ANYONE TO OPERATE THE TRANSPORTER HOIST WHO HAS NOT BEEN THOROUGHLY AND

PROPERLY TRAINED IN THE CORRECT OPERATION AND USE OF THIS HOIST.

5. This hoist is manufactured to lift materials only. Do not use the TranzSporter Hoist for the purpose of

transporting personnel from one level to another.

6. Do not climb the TP-Series hoist or use as a personnel ladder.

7. DO NOT OVERLOAD: Maximum lifting capacity for the TP250 is 250 lbs. with a load capacity of 230 lbs.

Maximum lifting capacity for the TP400 is 400 lbs. with a load capacity of 380 lbs.

8. Keep hands, feet and other body parts as well as clothing away from the track sections and moving or

rotating parts of the TranzSporter Hoist when starting the engine or when operating the hoist.

9. Do not allow any persons to walk or work under or near the TranzSporter Hoist while in operation.

10. Do not use this hoist to transport hot asphalt or any other hot molten substance from one elevation to another.

11. Never lift sheet or panel goods without the use of the plywood brackets and the tie down straps provided.

12. Always use roof top fall protection when setting up, operating, and taking down the Tranzsporter Hoist.

Safety Instructions Must Be

Viewed Before Operating Hoist

E1558

Instruction Sheet #08287, Rev. 11/23/20

https://www.youtube.com/watch?v=-jF4uT0YcB4

WARNING: This product can expose you to

chemicals including Nickel, which is known to

the State of California to cause cancer. For more

information go to: www.P65Warnings.ca.gov

Summary of content (8 pages)

PAGE 1
Safety Instructions for the TP250/400 Lift Hoist https://www.youtube.com/watch?v=-jF4uT0YcB4 General Safety Instructions: In order to set up and operate the TranzSporter ladder hoist safely in and around ELECTRIC POWER LINES and be compliant with OSHA Regulations 1926.416(a), the following must be ascertained prior to setting up the TranzSporter each time for the protection of employees. Safety Instructions Must Be Viewed Before Operating Hoist 1926.
PAGE 2
Raising and Lowering the Track Section Assembly WARNING: KEEP TRACK SECTIONS MINIMUM 10 FT. CLEAR OF ALL ELECTRICAL WIRES AND EQUIPMENT. BE AWARE OF OVERHEAD WIRES BEFORE RAISING TRACK SECTIONS. ELECTRICITY KILLS. The hoist assembly is extremely top heavy and must be kept under control at all times. Two alternate methods are suggested for raising the platform hoist to the operating position. Pic. 1 Pic. 2 Pic. 3 Procedure “A” (Pic.1) This procedure requires two or preferably three men. 1.
PAGE 3
Secure the Top Cap (Pic 5) Option 1 Low Top Cap Attach the “S” hooks included with the top cap hardware. Place in mousing holes on the back of the top cap. Tie off the “S” hooks with rope and secure with cross tie. Option 2 High Top Cap Pass rope threw the track section rungs. Tie off the rope and secure with cross tie.
PAGE 4
DANGER PELIGRO ELECTROCUTION HAZARD PELIGRO DE ELECTROCUTACION THIS PRODUCT CONDUCTS ELECTRICITY ESTE PRODUCTO CONDUCE ELECTRICIDAD FAILURE TO READ AND FOLLOW ALL INSTRUCTIONS ON THE HOIST AND TRACKS MAY RESULT IN INJURIES OR DEATH EL NO LEER Y SEGUIR TODAS LAS INSTRUCCIONES ACERCA DE LA PLATAFORMA MOTORIZADA Y LOS RIELES PODRIA RESULTAR EN LESIONES O MUERTE 404-344-0000 • tiedown.com 605 Stonehill Drive SW, Atlanta, GA 30336 sales@tiedown.
PAGE 5
DANGER PELIGRO ELECTROCUTION HAZARD PELIGRO DE ELECTROCUTACION THIS PRODUCT CONDUCTS ELECTRICITY ESTE PRODUCTO CONDUCE ELECTRICIDAD FAILURE TO READ AND FOLLOW ALL INSTRUCTIONS ON THE HOIST AND TRACKS MAY RESULT IN INJURIES OR DEATH EL NO LEER Y SEGUIR TODAS LAS INSTRUCCIONES ACERCA DE LA PLATAFORMA MOTORIZADA Y LOS RIELES PODRIA RESULTAR EN LESIONES O MUERTE 404-344-0000 • tiedown.
PAGE 6
Fijación de la tapa superior (Fig. 5) Opción 1 Tapa superior baja Fije los ganchos “S” incluidos en el equipo de la tapa superior. Ubique los orificios de alojamiento en la parte posterior de la tapa superior. Una los ganchos “S” con la soga y fíjelos con un amarre cruzado. Opción 2 Tapa superior alta Pase la soga a través de los peldaños de la sección de tramo. Ate la soga y fije con un amarre cruzado. Opción 3 Kit de anclaje de escalera y elevador n.
PAGE 7
Elevación y descenso del conjunto de la sección de tramo ADVERTENCIA: MANTENGA LAS SECCIONES DE TRAMO COMO MÍNIMO 10 PIES ALEJADAS DE CUALQUIER CABLE Y EQUIPO ELÉCTRICO. TENGA EN CUENTA LOS CABLES AÉREOS ANTES DE ELEVAR LAS SECCIONES DE TRAMO. LA ELECTRICIDAD MATA. El conjunto del elevador es extremadamente pesado y debe mantenerse bajo control en todo momento. Se sugieren dos métodos alternativos para elevar el elevador de plataforma hasta la posición de operación. Procedimiento “A” (Fig. 1) Fig.
PAGE 8
Instrucciones de seguridad para el elevador TP250/400 Instrucciones generales de seguridad: A fin de montar y operar el elevador escalera TranzSporter de forma segura en y alrededor de LÍNEAS DE ENERGÍA ELÉCTRICA y cumplir con las regulaciones de OSHA 1926.416(a), se debe comprobar lo siguiente antes de montar el TranzSporter cada vez para la protección de los empleados. https://www.youtube.com/watch?v=-jF4uT0YcB4 Las instrucciones de seguridad deben revisarse antes de operar el elevador 1926.