Instructions / Assembly

ManualsBrandsTie Down ManualsGarden Center48 in. x 6 in. Black Metal Landscape Edging Kit Garden Edging Steel Edging Border (6-Piece Kit)

404-344-0000 • www.tiedown.com

605 Stonehill Drive SW, Atlanta, GA 30336

sales@tiedown.com

Instruction 08438

EC1967; Rev. 6/20/23

Landscape Edging

Installation

WARNING: This product can expose you to chemicals including Nickel, which is known to the

State of California to cause cancer. For more information go to: www.P65Warnings.ca.gov

6 inch Landscaping Kit

ID# 33220 - 4 Plate Kit

Includes:

6” x 48” Edging Plates (4) & Connectors (4)

ID# 33227 - 6 Plate Kit

Includes:

6” x 48” Edging Plates (6) & Connectors (6)

8 inch Landscaping Kit

ID# 33221 - 4 Plate Kit

Includes:

8” x 48” Edging Plates (4) & Connectors (4)

ID# 33228 - 6 Plate Kit

Includes:

8” x 48” Edging Plates (6) & Connectors (6)

14 inch Landscaping Kit

ID# 33222

Includes:

14” x 48” Edging Plates (4)

1.25”x 14” Connectors (4)

Recommend Tools

Wood Block Hammer or

Mallet

Knee Pads Work Gloves &

Safety Glasses

Lawn Edger

Tie Down is here to help you own the edge on your landscaping with our metal edging solutions. Upgrade your lawn game with our

edging strips that deliver un-matched aesthetic and curb appeal, while also providing a barrier against weeds, unwanted grass, and

bugs from your ﬂower beds and overall landscape design. Our edging strips come easy-to-assemble with sharp teeth that cut through

dirt for a fast and easy installation. Whether you have a traditional or modern landscape, Tie Down Landscape Edging solution

complements any aesthetic and provides lasting results.

On Line

Instructions

Summary of content (4 pages)

PAGE 1
Landscape Edging Installation Tie Down is here to help you own the edge on your landscaping with our metal edging solutions. Upgrade your lawn game with our edging strips that deliver un-matched aesthetic and curb appeal, while also providing a barrier against weeds, unwanted grass, and bugs from your flower beds and overall landscape design. Our edging strips come easy-to-assemble with sharp teeth that cut through dirt for a fast and easy installation.
PAGE 2
Landscape Edging Installation STEP 1 Using a water hose as a guide. Place the hose along the route that will be final placement for the landscape edging. STEP 2 Using a straight edge spade or edging tool, insert the tool into the soil then begin tilting left and right then inward and outward tracing the path of the water hose. STEP 3 Place the edging along the specified route with the teeth facing downward. STEP 4 Place wood block over the center of the plate tap/drive down with a hammer.
PAGE 3
Landscape Edging Installation STEP 5 Place edging end to end unless overlapping to shorten length. Position the connector wedge on top of the edging plates, making sure both edging plates are wedged between the connector wedge. Drive down to secure connector. ELEVATION CHANGES To account for small hills or changes in elevation, you can create a gap at the joint of the material and use the connector to close the space. For steeper inclines, overlap the edging plates slightly.
PAGE 4
Landscape Edging Bending Tips Sharp Corners Place a block or wood block perpendicular across edging plate at the desired bend location. Bend edging plate to the desired angle while applying pressure to the block. Curved Bends Stand the material on the ground using your foot to hold in place. While holding the top end of the plate apply pressure to the middle in order to flex the material to the desired radius. Additional Hardware Available 90 Degree Angle Bracket Used for hard 90 degree turns.