ASNG007 Wood 7 Drawer Storage Cabinet V3.
IMPORTANT INFORMATION READ CAREFULLY. KEEP THIS INFORMATION FOR FURTHER REFERENCE. ••• GENERAL GUIDELINES Please read the following instruction carefully and use the product accordingly. Please keep this manual and hand it over when you transfer the product. This summary may not include every detail of all variations and considered steps. Please contact us when further information and help are needed. •• • NOTES Please follow the assembly instructions precisely and only use the product as intended.
5/16 (8 mm) 1/8 (3 mm) If you have any further questions, please feel free to contact us by email or official website: devaise-cs@devaise.com We will reply ASAP. Before installation, please make sure you have all the hardware, the serial numbers are properly labeled corresponging to the list, and the quantity is correct.
EXPLODED DRAWING 6 4 1 2 4 3 5 10 8 11 7 1 9 ×7
PARTS A X40 B X36 C X40 D X7 E X80 F X14 G X8 H X2 I X2 J X1 M4x14 = CL + DL + DR + CR REMARK CR CL DR DL 2
MINIFIX POSITION DEV ISE V 1 A X4 REMARK B X8 1. Put a blanket under the board to avoid scratch or damage. 2. Please do not screw A too deep or too shallow.
2 CR X6 E X24 CL X6 M4x14 TOP CL CR E E 1 E E E E E E E 1 E E E E 3 E E E E E E E E E E E BOTTOM 2 REMARK 1 When installing, please make sure the screws are flattened, not crooked; Otherwise the drawers will not be installed perfectly. 2 Please do not install the bottom drawer runner part in this step, Otherwise it will not be able to install the connector housing ( Part C ), the bottom drawer runner part will be installed in step 8.
3 1 C X4 2 3 2 1 C ×4 3 4 1 4 3 4 5
5 A A X8 8 6 5 6 1 C X8 6 C 8 3 5 1 6 3 5 6
7 E X16 M4x14 H X2 16 E 1 I X2 6 3 H H 5 I I 8 H Lockable casters I 360° Swivel Casters E X4 M4x14 CL X1 6 CR X1 E 4 1 3 CL 7 CR
A X14 9 B X14 B 2 10 9 A 2 ×7 10 A X14 B X14 B 2 8 7 ×7 A 2 8
11 C X14 8 10 C 9 2 C 8 10 9 ×7 12 C X14 7 11 11 7 9 11 9 C 2 10 8 11 7 9 9 ×7
E X28 DL X7 M4x14 8 10 DR X7 9 7 DL FRONT DR 11 8 DR FRONT FRONT E 3 2 1 DR FRONT E ×7 10
F X14 10 8 11 7 9 15 REMARK It is recommended to install the bottom drawer first to prevent tipping.
16 E X8 M4x14 G X8 G E + E G ×8 12
! WARNING WALL ANCHORING GUIDE ANTI-TIPPING DEVICE The hardware you should use to secure your furniture to the wall depends on both the type of furniture you have and your wall material. Attaching your furniture to cavity wall with anti-tipping device 27/64” (10.5mm) Anti-tipping device bag Type of Wall Material 1/8” (3mm) Fixing hole (round) Threading hole (oval) Electric drill (not provided) Using the guide below, identify your wall material and choose the correspongding steps.
STEP Drill a hole in the solid wall ( Wood wall or Concrete wall ) 1 using a 0.41~0.43 inches ( 10.5~11mm ) drill bit.
