TID TD-V2 Programming Guide INTRODUCTION TID TD-V2 is a UHF radio. It offers 16 channels, you can add or remove channels from scanning list and give channels alphanumeric names via programming with a computer. This Programming Guide will help you get a quick start to program the radio. *If you have any problem with the TD-V2 radio using or programming, please don’t hesitate to contact us via support: walkietalkiesoftware.com. Also visit our Facebook pages (TIDRADIO) for more help.
1. Frequency Chart 16 Modifiable FRS Two Way Channels (Channels 1-16) - Receive and Transmit. 2.Preparation before Programming 2.1. Computer System Requirements Manufacture Programming Software Operating System: Windows 7, Windows 8 and Windows 10 CHIRP Programming Software Operating System: Windows 7\8\10, Windows 2000, Mac OS, Linux 2
2.2. Programming Cable A.CH340 programming cable - The driver should be installed before programming. You can search B08QCW5CZJ on Amazon to purchase a CH340 programming cable if you do not have one. Product link: https://www.amazon.com/TIDRADIO-Driver-Programming-Portable-Radios/dp /B08QCW5CZJ/ref=sr_1_1?dchild=1&keywords=B08QCW5CZJ&qid=162797362 4&sr=8-1 Driver download link:walkietalkiesoftware.com 1) Find the corresponding driver of the system. 2) Click and wait for the download.
B. If you use a FTDI cable, it does not need to be installed with a driver. You can just plug in and use directly. You can search B08CB5KT5M on Amazon to purchase a FTDI cable if you do not have one. Product link: https://www.amazon.
ERROR: Failed to Connect to the transceiver (Radio) If it says it cannot connect to the radio - this means the cable is working but is not installed correctly into the radio. Items to Check: Radio is turned on The cable is FULLY inserted (it can be deceiving but there is a double click) Hold the cable into the radio - some radios might not make contact without pressure A way to cheat - dampen the pins of the cable before pushing it into the radio. This will give a solid contact 2.5.
3.CH340 programming cable port is USB-SERIAL CH340 (COM?) 4.FTDI programming cable port is USB Serial Port (COM?) 3.TD-V2 Manufacture Software Programming Process 1) Download and open the manufacture software. Click "Setting → Communication Port" and then Confirm the port the same as the port viewed by Device Manager, then click the ”OK” button.
2) Click the "Read" button, then click "Start" and ready to read the data from your radio.( Make sure the radio is turned on) 3) You will come to the parameter page and adjust the parameters. According to the US FCC rule, FRS radio cannot modify the frequency and bandwide.
Channel Information The TD-V2 radio has 16 channels, you can edit the channel number and channel information according to your needs. The following is an introduction to each term. Name Meaning Setting Description Rx Freq. Receiving frequency FRS frequency（Fixed） Tx Freq. Transmitting frequency FRS frequency（Fixed） Rx CTC/DCS Code Receiving CTCSS/DCS Refer to the DCS table and Mutes the speaker of the CTCSS table in the manual. transceiver in the absence of a specific low level digital signal.
4) You can adjust the parameters (VOX Function, Squelch, Side Key, Voice Prompt, Scan, etc.) Basic Setting Name Meaning SQL Squelch Level Side Key OFF/Monitor/High /Low Power/Alarm TOT[s] Transmission time-out timer Settings Description 0-9 Mutes the speaker of the transceiver in the absence of a strong signal. Squelch is either 0 or 1-9 levels. The higher level, the stronger the signal must be to in-mute the speaker.
5) Finally, all the modification will be saved by clicking the "Write" button, then clicking the "Start" button on the popup. And you can check the setting you modified after reboot the radio.
4.
3) And you will come to the page of Memories, in which you can adjust the limited parameters . 4)Then if you switch to the page of Settings, you can adjust the limited parameters(For the explanation of Voice prompt, Scan, VOX, Squelch, etc.
Name Settings Description Voice prompt Enabled/Off Switch voice prompts Voice language English/Chinese Switch the language Scan Enabled/Off In the scan mode, whether add the channel to the scan list. 1-5 When enabled it is not necessary to push the [PTT] button on the transceiver. Adjust the gain level to an appropriate sensitivity to allow smooth transmission. Squelch level 0-9 Mutes the speaker of the transceiver in the absence of a strong signal. Squelch is either 0 or 1-9 levels.
5) All the modification will be saved by clicking "Upload To Radio" under "Radio". Then you can check the settings you modified after reboot the radio. *If you have any problem with the TID TD-V2 radio using or programming, please don’t hesitate to contact us via support: walkietalkiesoftware.com. Also visit our Facebook pages (TIDRADIO) for more help. It’s always our honor to help.
