Thundercomm TurboX C865 System on Module Thundercomm TurboXTM C865 System on Module A high performance embedded platform based on Qualcomm® Snapdragon™ QRB5165 processor Description Thundercomm TurboXTM C865 System on Module (SOM) is a high performance intelligent module, integrating Android, based on Qualcomm QRB5165 processor. It integrates the advanced 7 nm Fin FET process, a customized 64-bit Octa-core Qualcomm Kryo 585 applications processor. C865 SOM supports long range Wi-Fi, Wi-Fi 6 (Wi-Fi 802.
Thundercomm TurboX C865 System on Module Adreno GPU 650 - 4K 60 fps UI or 2x 2k 60 fps UI Graphics OpenGL ES 3.2, Vulkan 1.1, DX12 FL 12_1 OpenCL 2.0 full profile 2 x 4-lane DSI D-PHY 1.2 and DisplayPort 1.
Thundercomm TurboX C865 System on Module SoundWire interface for codec SoundWire interface for smart speaker amplifier 3x MI2S with two data lanes to support full duplex stereo Audio Interface 1x MI2S with four data lanes for up to eight channels 3 DMIC ports supports up to 6 DMICs USB 2x USB 3.1 GEN2, one can support Type-C with DisplayPort PCIe 2 x 2-lane PCIe Gen3.0 2 x RF connector for WiFi /BT, 2 x USB 3.
Thundercomm TurboX C865 System on Module 2. Change GPIO 117 to GPIO 70 V1.2 Jan 21,2021 V1.3 Apr.16, 2021 Fix typo for pin number of CCI_I2C in chapter 2.2.4 Fix typo for pin number of table2.2-1 for VREG_IO_1P8, from B44 to B43; Fix typo for pin number of table2.2-8 for SD_UFS_CARD_DET_N, from G34 to G43 Table of Contents 1 2 Physical Description ............................................................................................................................................ 6 1.
Thundercomm 3 4 TurboX C865 System on Module 2.2.14 Sensor Interrupt Interface .......................................................................................................... 23 2.2.15 Debug UART Interface .............................................................................................................. 23 2.2.16 Battery Interface ........................................................................................................................ 23 2.2.
Thundercomm TurboX C865 System on Module 4.17 Power Consumption........................................................................................................................... 47 4.18 Thermal .............................................................................................................................................. 47 4.19 RF Performance ................................................................................................................................. 48 4.
Thundercomm TurboX C865 System on Module Figure 1.2-1 TurboX C865 SOM Key component Location 1.3 Connectors Function and Part Number Figure 1.3-1 TurboX C865 SOM Connector PIN Location Below table indicates connectors detail information. Part Reference Description Copyright © 2018 All Rights Reserved, Thundercomm Technology Co., Ltd.
Thundercomm CON1 TurboX C865 System on Module BTB connectors, used for connecting to Carrier Board. SEAM8-50-S02.0-L-10-2 SAMTEC J2 JTAG connector, used for JTAG Debug AXF5D1612 Panasonic Or J2 JTAG connector, used for JTAG Debug 20843-050E-21 I-PLEX J1501,J5907 RF antenna connector 20449-001E I-PLEX Table 1.3-1 Connector part number and information 1.4 Package Drawing and Dimensions Figure 1.4-1 Top View Copyright © 2018 All Rights Reserved, Thundercomm Technology Co., Ltd.
Thundercomm TurboX C865 System on Module Figure 1.4-2 Side View Figure 1.4-3 Bottom View Copyright © 2018 All Rights Reserved, Thundercomm Technology Co., Ltd.
Thundercomm TurboX C865 System on Module 2 Interfaces Description This chapter introduces all the interfaces definition, purpose to guide developer easy to design and verification on Thundercomm TurboXTM C865 SOM. 2.1 Interfaces Parameter Definitions Symbol Description AI Analog input AO Analog output B Bidirectional digital with CMOS input CSI Supply voltage for MIPI_CSI circuits and I/O; (1.2 V for low power mode) DI Digital input(CMOS) DSI Supply voltage for MIPI_CSI circuits and I/O; (1.
Thundercomm TurboX C865 System on Module PD Contains an internal pull-down device PU Contains an internal pull-up device P3 Power group 3, it is 1.8V. P2 SDC Power group 2, it is 1.8V or 2.95V. Table 2.1-1 Interfaces parameter definitions 2.2 Interfaces Detail Description 2.2.1 Power Supply Interface Below table describes all interfaces of SOM Power Supply. For the detail parameter request, please refer the chapter on Electrical specifications. Power Supply PIN Name Conn.
Thundercomm TurboX C865 System on Module D24,D26,D28,D30,D32,D3 4,E3,F11,F13,F15,F17,F19, F21,F23,F25,F27,F29, F31,F33,F35,F47,F48,F49, F50,G11,G13,G15,G17,G1 9,G21,G23,G25,G27,G48, G49,G50,H12,H14,H16,H1 8,H20,H22,H24,H48,H49, H50,K11,K13,K15,K17,K1 9,K21,K23,K25 Table 2.2-1 Power Supply Definition 2.2.2 Touchscreen Interface Touchscreen panels are supported using I2C buses and GPIOs configured as discrete digital inputs.
Thundercomm DSI0_NC_LN3_M DSI1_A0_LN0_P DSI1_B0_LN0_M DSI1_C0_LN1_P DSI1_A1_LN1_M DSI1_B1_CLK_P DSI1_C1_CLK_M DSI1_A2_LN2_P DSI1_B2_LN2_M DSI1_C2_LN3_P DSI1_NC_LN3_M TurboX C865 System on Module CON1 CON1 CON1 CON1 CON1 CON1 CON1 CON1 CON1 CON1 CON1 J20 B26 C26 A27 B27 A25 B25 B24 C24 B28 C28 DSI DSI DSI DSI DSI DSI DSI DSI DSI DSI DSI AO AO AO AO AO AO AO AO AO AO AO MIPI1 Signals for MIPI LCM Compliant with MIPI Alliance Specification for Display Serial Interface Table 2.
Thundercomm TurboX C865 System on Module CAM_MCLK1 CON1 G14 P3 DO CSI1_NC_CLK_P CSI1_A0_CLK_M CSI1_B0_LN0_P CSI1_C0_LN0_M CSI1_A1_LN1_P CSI1_B1_LN1_M CSI1_C1_LN2_P CSI1_A2_LN2_M CSI1_B2_LN3_P CSI1_C2_LN3_M CON1 CON1 CON1 CON1 CON1 CON1 CON1 CON1 CON1 CON1 B17 A17 C16 B16 C18 B18 B15 A15 C14 B14 CSI CSI CSI CSI CSI CSI CSI CSI CSI CSI AI AI AI AI AI AI AI AI AI AI already pull up on SOM Camera main clock output MIPI Signals of Camera1 Compliant with MIPI Alliance Standard Specification Camera2
Thundercomm TurboX C865 System on Module CSI3_B1_LN1_M CSI3_C1_LN2_P CSI3_A2_LN2_M CSI3_B2_LN3_P CSI3_C2_LN3_M CON1 CON1 CON1 CON1 CON1 A23 C22 B22 B21 A21 CSI CSI CSI CSI CSI AI AI AI AI AI CAM_MCLK3 CON1 G18 P3 DO Camera main clock output Camera4 Interface CSI4_NC_CLK_P CSI4_A0_CLK_M CSI4_B0_LN0_P CSI4_C0_LN0_M CSI4_A1_LN1_P CSI4_B1_LN1_M CSI4_C1_LN2_P CSI4_A2_LN2_M CSI4_B2_LN3_P CSI4_C2_LN3_M CON1 CON1 CON1 CON1 CON1 CON1 CON1 CON1 CON1 CON1 E24 F24 D23 E23 D25 E25 E22 F22 D21 E21 CSI CSI
Thundercomm TurboX C865 System on Module Audio Interface PIN Name Locati on PIN Vol tage Type WCD_SWR_TX_CLK CON1 K26 P3 DO WCD_SWR_TX_DATA0 CON1 K27 P3 DO WCD_SWR_TX_DATA1 CON1 K28 P3 DO WCD_SWR_RX_CLK CON1 K29 P3 DI WCD_SWR_RX_DATA0 CON1 K30 P3 DI WCD_SWR_RX_DATA1 CON1 K31 P3 DI WSA_SWR_DATA CON1 G45 P3 IO WSA_SWR_CLK CON1 G46 P3 IO DMIC01_CLK CON1 K43 P3 DO LPI_MI2S1_CLK DMIC01_DATA CON1 K44 P3 IO LPI_MI2S1_WS DMIC23_CLK CON1 J43 P3 DO LPI_M
Thundercomm TurboX C865 System on Module The SOM support 2 x USB 3.1 GEN2, one can support Type-C with DisplayPort. USB mode and DisplayPort mode can be simultaneously operating at USB 3.1 GEN2 (10 Gbps) and DP 1.4(8.1 Gbps). PIN Type Description USB0_SS_RX0_M USB0_SS_RX0_P USB0_SS_RX1_M USB0_SS_RX1_P USB0_SS_TX0_M USB0_SS_TX0_P USB0_SS_TX1_M USB0_SS_TX1_P Locati on CON1 CON1 CON1 CON1 CON1 CON1 CON1 CON1 A31 B31 C30 B30 C32 B32 A33 B33 DO DO DI DI DO DO DI DI USB 3.0 Signals Compliant with USB 3.
Thundercomm TurboX C865 System on Module PCIE1_RX1_P PCIE1_TX0_M PCIE1_TX0_P PCIE1_TX1_M PCIE1_TX1_P GPIO_83 GPIO_82 GPIO_84 PCIE2_REFCLK_M_MDM PCIE2_REFCLK_P_MDM PCIE2_RX0_M_MDM PCIE2_RX0_P_MDM PCIE2_RX1_M_MDM PCIE2_RX1_P_MDM PCIE2_TX0_M_MDM PCIE2_TX0_P_MDM PCIE2_TX1_M_MDM PCIE2_TX1_P_MDM GPIO_86 GPIO_85 CON1 CON1 CON1 CON1 CON1 CON1 CON1 CON1 CON1 CON1 CON1 CON1 CON1 CON1 CON1 CON1 CON1 CON1 CON1 CON1 F12 D15 E15 E14 F14 G39 G37 G38 J21 H21 J23 H23 K22 J22 K24 J24 J25 H25 D39 F39 AI AO AO AO AO DI DO
Thundercomm SPI2_CS_IMU TurboX C865 System on Module CON1 P3 J39 IO GPIO167 Table 3.2-8 SSC interface definition 2.2.9 SDIO Interface The SOM support dual 4-laneSDIO, SDC2 connect to SD-card. The SDIO is high-speed signal group. It should protect other sensitive signals/circuits from SD corruption, and protect SD signals from noisy signals (clock, RF and so on). The clock can be up to 200 MHz. The signals routing should be 50ohm ±10% impedance control.
Thundercomm TurboX C865 System on Module I2C is a two-wire bus that can be routed to multiple devices; each line of each bus need to supplement by a 2.
Thundercomm TurboX C865 System on Module GPIO53 CON1 F37 P3 IO GPIO54 CON1 C42 P3 IO GPIO55 CON1 F36 P3 IO GPIO56 CON1 G35 P3 IO GPIO57 CON1 F34 P3 IO GPIO58 CON1 G34 P3 IO GPIO59 CON1 G33 P3 IO GPIO8 CON1 A46 P3 IO GPIO9 CON1 D35 P3 IO RGB_1V2_EN CON1 K40 P3 IO GPIO 116 CON1 K41 P3 IO GPIO125 CON1 A9 P3 IO 6DOF_ULPM CON1 B45 P3 IO WSA2_EN CON1 B41 P3 IO 6DOF_L_RST CON1 B44 P3 configured to GPIO or SPI or I2C QUP18 can be configured
Thundercomm CBL_PWR_N TurboX C865 System on Module CON1 pulled up internally through a 200K resistor to 1.8V A45 Signal use for auto power on when you plug in a battery, active low, internal pull up DI Table 3.2-11 Power on interface definition 2.2.
Thundercomm TurboX C865 System on Module signal, Low active VOL_UP_N CON1 A41 P3 Volume up key signal, Low active DI Table 3.2-6 Keys interface definition 2.2.14 Sensor Interrupt Interface All these interfaces dedicate to below sensors.
Thundercomm TurboX C865 System on Module BATT_ID CON1 K45 0~1.875V AI Battery ID sense input signal Table 3.2-9 Battery interface definition 2.2.17 ADCs Interface The ADC input signal use as analog multiplexer function. ADCs PINs PIN Name Location PIN Voltage Type PM_GPIO5 CON1 A6 0~1.875V LV GPIO_6_PWM CON1 K38 0~1.875V LV PM_GPIO7 CON1 A7 0~5V MV PM_GPIO10 CON1 A8 0~5V MV Description ADC input, can be configured as 1.8V ADC input, can be configured as 1.
Thundercomm TurboX C865 System on Module connect to positive port Table 3.2-11 PWMs and LED Current Driver interface definition 2.2.19 Antenna Interface The SOM provides the fully-integrated WLAN and Bluetooth function. The WLAN and Bluetooth share the antenna port with 50ohm impedance. WLAN supports 2 × 2 multiple input, multiple output (MIMO) with two spatial streams IEEE802.11 a/b/g/n/ac/ax WLAN standards. Supports Bluetooth 5.
Thundercomm TurboX C865 System on Module 3 Connector PIN Summary 3.
Thundercomm A37 A38 A39 A40 A41 A42 A43 A44 A45 A46 A47 A48 A49 A50 B1 B2 B3 B4 B5 B6 B7 B8 B9 B10 B11 B12 B13 B14 B15 B16 B17 B18 B19 B20 B21 B22 B23 B24 B25 B26 B27 B28 B29 PMK8002_RF_CLK2 DISP0_RESET_N SDM_FAST_BOOT_2 DEBUG_PMIC_PKD_N DEBUG_KEY_VOL_UP_N DEBUG_KEY_VOL_DOWN_N PM855_USB_SBU1 PM855_USB_SBU2 CBL_PWR_N GPIO_8_C VDISP_P_OUT VDISP_M_OUT VREG_L11C_3P3 VREG_L9C_2P96 GPIO_168 GND GND VREG_L5C_1P8 VREG_L5C_1P8 GPIO_135 GPIO_162 GPIO_163 GPIO_12 GPIO_13 SDC2_DATA_3 SDC2_DATA_0 SDC2_CLK_CONN CSI1_C2_
Thundercomm B30 B31 B32 B33 B34 B35 B36 B37 B38 B39 B40 B41 B42 B43 B44 B45 B46 B47 B48 B49 B50 C1 C2 C3 C4 C5 C6 C7 C8 C9 C10 C11 C12 C13 C14 C15 C16 C17 C18 C19 C20 C21 C22 USB0_SS_RX1_P USB0_SS_RX0_P USB0_SS_TX0_P USB0_SS_TX1_P DP_AUX_P PMK8002_PMIC_CLK FP_SPI_CLK FP_SPI_MOSI MDM_SKIN_THERM GPIO_9_P WSA1_EN WSA2_EN VREG_L8C_1P8 VREG_IO_1P8 6DOF_L_RST 6DOF_ULPM SDM_DEBUG_UART_TX SDM_FAST_BOOT_0 GND GND GND GND RF_CLK1 GND NC PM8250_GPIO3 NC PM8150L_AMUX1 NC PM8150B_AMUX1 NC GND SDC2_DATA_1 GND CSI1_B2_LN
Thundercomm C23 C24 C25 C26 C27 C28 C29 C30 C31 C32 C33 C34 C35 C36 C37 C38 C39 C40 C41 C42 C43 C44 C45 C46 C47 C48 C49 C50 D1 D2 D3 D4 D5 D6 D7 D8 D9 D10 D11 D12 D13 D14 D15 GND DSI1_B2_LN2_M GND DSI1_B0_LN0_M GND DSI1_NC_LN3_M GND USB0_SS_RX1_M GND USB0_SS_TX0_M GND DP_AUX_N GND FP_SPI_CS FP_SPI_MISO FSA_INT_N GPIO_10_P GPIO_88 GPIO_89 GPIO_54 SDM_FORCE_USB_BOOT 6DOF_R_RS SDM_DEBUG_UART_RX WCD_RESET_N GND GND GND GND NC GND RF_CH1_CON GND SDM_WDOG_DISABLE NC GPIO_137 NC NC NC PCIE1_RX0_M GND PCIE1_REFCLK
Thundercomm D16 D17 D18 D19 D20 D21 D22 D23 D24 D25 D26 D27 D28 D29 D30 D31 D32 D33 D34 D35 D36 D37 D38note1 D39 D40 D41 D42 D43 D44 D45 D46 D47 D48 D49 D50 E1 E2 E3 E4 E5 E6 E7 E8 GND CSI2_C1_LN2_P GND CSI2_B0_LN0_P GND CSI4_B2_LN3_P GND CSI4_B0_LN0_P GND CSI4_A1_LN1_P GND CSI5_B0_LN0_P GND CSI5_A1_LN1_P GND USB1_HS_DM GND USB1_SS_RX_M GND GPIO_9_C GPIO_64 6DOF_L_STROBE GPIO_140_CON GPIO_86 TS_INT_N TS_I2C_SCL TS_RESET_N VREG_L2A_3P1 GPIO_73_C VREG_S4A_1P8 VREG_S4A_1P8 VREG_BOB VREG_BOB VPH_PWR VPH_PWR NC
Thundercomm E9 E10 E11 E12 E13 E14 E15 E16 E17 E18 E19 E20 E21 E22 E23 E24 E25 E26 E27 E28 E29 E30 E31 E32 E33 E34 E35 E36 E37note1 E38 E39 E40 E41 E42 E43 E44 E45 E46 E47 E48 E49 E50 F1 NC NC PCIE1_RX0_P PCIE1_RX1_M PCIE1_REFCLK_P PCIE1_TX1_M PCIE1_TX0_P CSI2_B2_LN3_P CSI2_A2_LN2_M CSI2_A1_LN1_P CSI2_C0_LN0_M CSI2_NC_CLK_P CSI4_C2_LN3_M CSI4_C1_LN2_P CSI4_C0_LN0_M CSI4_NC_CLK_P CSI4_B1_LN1_M CSI5_B2_LN3_P CSI5_C0_LN0_M CSI5_C1_LN2_P CSI5_B1_LN1_M CSI5_NC_CLK_P USB1_HS_DP USB1_SS_TX_M USB1_SS_RX_P PMIC_SPM
Thundercomm F2 F3 F4 F5 F6 F7 F8 F9 F10 F11 F12 F13 F14 F15 F16 F17 F18 F19 F20 F21 F22 F23 F24 F25 F26 F27 F28 F29 F30 F31 F32 F33 F34 F35 F36 F37 F38 F39 F40 F41 F42 F43 F44 NC NC NC NC NC NC NC NC NC GND PCIE1_RX1_P GND PCIE1_TX1_P GND CSI2_C2_LN3_M GND CSI2_B1_LN1_M GND CSI2_A0_CLK_M GND CSI4_A2_LN2_M GND CSI4_A0_CLK_M GND CSI5_C2_LN3_M GND CSI5_A2_LN2_M GND CSI5_A0_CLK_M GND USB1_SS_TX_P GND GPIO_57 GND GPIO_55 GPIO_53 GPIO_2 GPIO_85 6DOF_R_STROBE SLEEP_CLK CONFIRM MDP_VSYNC_P APPS_I2C_SDA TurboX C86
Thundercomm F45 F46 F47 F48 F49 F50 G1 G2 G3 G4 G5 G6 G7 G8 G9 G10 G11 G12 G13 G14 G15 G16 G17 G18 G19 G20 G21 G22 G23 G24 G25 G26 G27 G28 G29 G30 G31 G32 G33 G34 G35 G36 G37 PM_FAULT_N USB_CC1 GND GND GND GND NC NC NC NC NC NC NC NC NC NC GND CAM_MCLK0 GND CAM_MCLK1 GND CAM_MCLK2 GND CAM_MCLK3 GND CAM_MCLK4 GND CAM_MCLK6 GND CAM_MCLK5 GND CAM2_RST_N GND CCI_I2C_SDA0 CCI_I2C_SCL0 CCI_I2C_SDA1 CCI_I2C_SCL1 GPIO_24 GPIO_59 GPIO_58 GPIO_56 GPIO_52 6DOF_1V2_EN TurboX C865 System on Module FAULT_N for PMIC CC1
Thundercomm G38 G39 G40 G41 G42 G43 G44 G45 G46 G47 G48 G49 G50 H1 H2 H3 H4 H5 H6 H7 H8 H9 H10 H11 H12 H13 H14 H15 H16 H17 H18 H19 H20 H21 H22 H23 H24 H25 H26 H27 H28 H29 H30 6DOF_2V8_EN 6DOF_1V8_EN GPIO_22_C GPIO_23 CAM1_RST_N SD_UFS_CARD_DET_N GPIO_144_C WSA_SWR_DATA WSA_SWR_CLK VBATT_CONN_VSENSE_M GND GND GND NC NC NC NC NC NC NC NC NC NC CSI0_A0_CLK_M GND CSI0_A1_LN1_P GND CSI0_C1_LN2_P GND DSI0_C1_CLK_M GND DSI0_B2_LN2_M GND PCIE2_REFCLK_P_MDM GND PCIE2_RX0_P_MDM GND PCIE2_TX1_P_MDM GPIO_31 GPIO_30 GP
Thundercomm H31 H32 H33 H34 H35 H36 H37 H38 H39 H40 H41 H42 H43 H44 H45 H46 H47 H48 H49 H50 J1 J2 J3 J4 J5 J6 J7 J8 J9 J10 J11 J12 J13 J14 J15 J16 J17 J18 J19 J20 J21 J22 J23 GPIO_5 GPIO_7 GPIO_4 CCI_I2C_SDA2 CCI_I2C_SCL2 CCI_I2C_SCL3 SNS_I2C0_SCL SNS_I2C4_SDA SNS_I2C4_SCL GPIO_173 GPIO_174 GPIO_175 GPIO_172 B_LED G_LED R_LED VBATT_CONN_VSENSE_P GND GND GND NC NC NC NC NC NC NC NC NC NC CSI0_NC_CLK_P CSI0_B0_LN0_P CSI0_B1_LN1_M CSI0_B2_LN3_P CSI0_A2_LN2_M DSI0_B0_LN0_M DSI0_B1_CLK_P DSI0_A1_LN1_M DSI0_A2_L
Thundercomm J24 J25 J26 J27 J28 J29 J30 J31 J32 J33 J34 J35 J36 J37 J38 J39 J40 J41 J42 J43 J44 J45 J46 J47 J48 J49 J50 K1 K2 K3 K4 K5 K6 K7 K8 K9 K10 K11 K12 K13 K14 K15 K16 PCIE2_TX0_P_MDM PCIE2_TX1_M_MDM CABC GPIO_14 GPIO_15 ALPS_INT_N EYETCK_2V8_EN CAM3_RST_N SEN1_GYRO_INT2 SEN1_ACCL_INT1 TE CCI_I2C_SDA3 GPIO_25 SNS_I2C0_SDA SPI2_CLK_IMU SPI2_CS_IMU SPI2_MISO_IMU SPI2_MOSI_IMU GPIO_87 DMIC23_CLK DMIC23_DATA DMIC45_CLK DMIC45_DATA VBAT_CON VBAT_CON VBAT_CON VBAT_CON NC NC NC NC NC NC NC NC NC NC GND CSI
Thundercomm K17 K18 K19 K20 K21 K22 K23 K24 K25 K26 K27 K28 K29 K30 K31 K32 K33 K34 K35 K36 K37 K38 K39 K40 K41note1 K42note1 K43 K44 K45 K46 K47 K48 K49 K50 TurboX C865 System on Module GND DSI0_C0_LN1_P GND DSI0_C2_LN3_P GND PCIE2_RX1_M_MDM GND PCIE2_TX0_M_MDM GND WCD_SWR_TX_CLK WCD_SWR_TX_DATA0 WCD_SWR_TX_DATA1 WCD_SWR_RX_CLK WCD_SWR_RX_DATA0 WCD_SWR_RX_DATA1 GPIO_0 GPIO_134 GPIO_133 GPIO_123 GPIO_26 CAM0_RST_N GPIO_6_PWM DISPLAY_RESX2 RGB_1V2_EN GPIO 116 GPIO 70 DMIC01_CLK DMIC01_DATA BATT_ID BATT_THE
Thundercomm TurboX C865 System on Module 3.2 J2 BTB Connector Pin Signal Name Pin Signal Name 1 SDM_JTAG_TMS 9 SDM _JTAG_SRST_N 2 SDM_JTAG_TCK 10 SDM _DEBUG_UART_TX 3 SDM _JTAG_TDO 11 SDM_DEBUG_UART_RX 4 SDM _JTAG_TDI 12 VREG_S4A_1P8 5 SDM _JTAG_TRST_N 13 SDM _PS_HOLD 6 DEBUG_PMIC_PKD_N 14 SDM _FORCE_USB_BOOT 7 DEBUG_KEY_VOL_DOWN_N 15 SDM _WDOG_DISABLE 8 GND 16 SDM _RESOUT_N Copyright © 2018 All Rights Reserved, Thundercomm Technology Co., Ltd.
Thundercomm TurboX C865 System on Module 4 Electrical Characteristics 4.1 Absolute Maximum Ratings The SOM needs to be designed in the operation conditions which is shown as below table. Parameter Min Max Units -0.3 -0.3 28 6 V V -0.3 6 V ±2000 ±500 V V Input Power Voltage USB_VBUS VBAT VBATT_CONN_VSENSE_P, VBATT_CONN_VSENSE_M, RSENSE_EXT_M, RSENSE_EXT_P ESD ESD-HBM model rating ESD-CDM model rating Table 4.
Thundercomm TurboX C865 System on Module Note: For the thermal conditons, operatin and storage min and max temperature is only when the module is fully tested and approved in the Initial Production stage. 4.3 Output Power The SOM provide power supply for external device, like camera module, SD card, Sensor, and so on. Below map show the details. Default Programble Rated voltage(V) range(V) current(mA) VREG_L11C_3P3 VREG_L9C_2P96 VREG_L5C_1P8 VREG_L8C_1P8 VREG_IO_1P8 VREG_L2A_3P1 VREG_S4A_1P8 +3.
Thundercomm VOL RPULL-UP RPULL-DOWN TurboX C865 System on Module Low-level output voltage, CMOS 0.0 0.45 V Pull-up resistance 20 K 60 K Ω Pull-down resistance 60 K 20 K Ω Table 4.4-1 Digital IO voltage performance 4.4.2 SD card digital I/O characteristics The SD card is powered by P2 supply; the power is 1.8V and 2.96V.the following table shows the SD card digital I/O characteristics: Parameter Description VIH High-level input voltage VIL Low-level input voltage Min 1.27/0.
Thundercomm TurboX C865 System on Module MIPI Alliance Specification for CPHY v1.0 None Table 4.5-1 MIPI_DSI Applicable standard Feature exceptions RAW7 not supported DPCM MIPI Alliance Specification for CSI-2 v1.3 predictor 2 not supported MIPI Alliance Specification for DPHY v1.2 None MIPI Alliance Specification for CPHY v1.0 The maximum supported data rate is 1.5Gsps Table 4.5-2 MIPI_CSI 4.6 USB The SOM supports USB standards and exceptions.
Thundercomm TurboX C865 System on Module VESA DisplayPort V1.4 HBR3 Table 4.8-1 DP 4.9 SLIMbus The SOM supports SLIMbus HDMI standards and exceptions Applicable standard MIPI Alliance Specification for Serial Low-power Interchip Media Bus Version 1.01.01 Feature exceptions None Table 4.9-1 SLIMbus 4.10 SDIO The SOM Supports SD standards and exceptions Applicable standard Feature exceptions Secure Digital: Physical Layer Specification version 3.0 None SDIO Card Specification version 3.
Thundercomm TurboX C865 System on Module Table 4.11-1 I2S Figure 4.11-1 I2S timing diagram The word-select signal is a 50% duty cycle signal Data is delayed 1 bit-clock, relative to the word select. Data outputs are launched on the falling edge of the clock, and inputs data are captured on the rising edge of the clock by the receiver. I2S samples are 2’s complement values, and the MSB is transmitted first allowing the transmitter and receiver to support different number of bits per sample.
Thundercomm TurboX C865 System on Module Using internal SCK Frequency – – – 24.576 MHz – 40.69 – – ns t(HC) Clock high – 0.45 × T – 0.55 × T ns t(LC) Clock low – 0.45 × T – 0.55 × T ns t(sr) SD and WS input setup time – 8.14 – – ns t(hr) SD and WS input hold time – 0 – – ns t(dtr) SD and WS output delay – – – 6.10 ns – – – 24.576 MHz – 40.69 – – ns t(HC) Clock high – 0.45 × T – 0.55 × T ns t(LC) Clock low – 0.45 × T – 0.
Thundercomm TurboX C865 System on Module compensates for the variation in battery characteristics across temperature changes and aging effects. This provides a dependable state of charge estimate throughout the entire life of the battery and across a broad range of operating conditions. Function Min Type Max Units Expected use VBATT_CONN_VSENSE_P (H47)& VBATT_CONN_VSENSE_M(G47) Resolution 1 16 bits Voltage ADC 450 Kohm ID ADC 16 bits Current ADC Table 4.14-1 Fuel Gauge 4.
Thundercomm TurboX C865 System on Module 4.17 Power Consumption Power Consumption S/N Normal Operation Current 1 (Play Movie ) -Play mp4 4K average value 4K60 Normal Operation Current (Camera mode) - HDMI Output mA TBD video mA TBD mA TBD mA TBD μA TBD ON Normal Operation Current (Sleep Mode) - No LCD. No camera TBD Take photo WiFi OFF 4 TBD 1080P WiFi 3 DUT mA -Loudspeaker 2 UNIT Test Items and Test Condition Leakage current Table 4.17-1 Power Consumption 4.
Thundercomm TurboX C865 System on Module Thermal Test Result Test Location Temperature(Max) 1 Environment Temperature 25 2 DDR TBD TBD 3 UFS TBD TBD 4 PM8250 TBD TBD 5 PM8150B TBD TBD 6 PM8150L TBD TBD 7 QCA6391 TBD TBD 8 PCB TBD TBD △T Figure 4.18-1 Thermal Data Heat Sink Design Copyright © 2018 All Rights Reserved, Thundercomm Technology Co., Ltd.
