Data Sheet
Table Of Contents
- 5.User Manual
- Revision History
- Table List
- About This Document
- Table of Contents
- Chapter 1. Overview
- Chapter 2. Interfaces Description
- 2.1. Interfaces parameter definitions
- 2.2. Pin description
- 2.3. Interfaces detail description
- 2.3.1. Power supply interface
- 2.3.2. RGMII interfaces
- 2.3.3. SPDIF interface
- 2.3.4. Audio interface
- 2.3.5. USB interface
- 2.3.6. PCIe interface
- 2.3.7. MIPI DSI interface
- 2.3.8. HDMI interface
- 2.3.9. JTAG interface
- 2.3.10. SDIO interface
- 2.3.11. BLSP interface
- 2.3.12. Power on interface
- 2.3.13. Reset interface
- 2.3.14. Boot configuration interface
- 2.3.15. Debug UART interface
- 2.3.16. PWM
- 2.3.17. Sleep clock
- 2.3.18. SPMI
- 2.3.19. Antenna interface
- Chapter 3. Electrical Characteristics
- Appendix 1. Notices
- Appendix 2. Trademarks
- 5.User Manual_ Warning
Thundercomm TurboX C40x SOM Datasheet
- 14 -
Pad# Function Voltage Type Function description
B7 HDMI_TCLK_M - -
HDMI clock negative.
For TurboX C404 and C430 do not connect.
B8 HDMI_TX0_M - -
HDMI TMDS data 0 negative.
For TurboX C404 and C430: do not connect.
B9 PCIE0_RX_P - DI PCIE receiver plus
B10 USB_SS_TX_P - DO USB 3.0 transmitter differential pair plus
B11 USB_SS_RX_M - DI USB 3.0 receiver differential pair minus
B12 USB1_HS_DM - IO USB1 HS data minus
B13 GND - - -
B14 SDC2_DATA_2 SDC2 IO Secure digital controller 2 data bit 2
B15 SDC2_DATA_0 SDC2 IO Secure digital controller 2 data bit 0
B16 SDC2_CMD SDC2 IO Secure digital controller 2 command
B17 GND - - -
B18 GPIO_15 1.8V IO Can be configured as GPIO
B19 GND - - -
B20 USB0_HS_ID 1.8V DI USB0 ID Pin
B21 GND - - -
B22 QCS_RESOUT_N 1.8V DO QCS reset output (active low)
B23 GND - - -
B24 GPIO_51 1.8V IO Can be configured as GPIO
B25 GPIO_53 1.8V IO Can be configured as GPIO
B26 GPIO_55 1.8V IO Can be configured as GPIO
B27 GPIO_57 1.8V IO Can be configured as GPIO
B28 GPIO_59 1.8V IO Can be configured as GPIO
B29 GPIO_119 1.8V IO Can be configured as GPIO
C1 PON_1 V_Internal DI Level-high triggered power-on input (keep high)
C2 QCS_RESIN_N 1.8V DI System reset input for JTAG debugging
C3 WCD_MCLK 1.8V DO Audio reference clock output for Qualcomm audio codec
C4 PM_GPIO_06 1.8V IO PMS405 GPIO, and can be configured as GPIO
C5 PM_RESIN_N 1.8V DI Power management reset in (active low)
C6 KPDPWR_N V_Internal DI Power-on trigger, level trigger (active low)
C7 PM_GPIO_04 1.8V IO PMS405 GPIO, and can be configured as GPIO
C8 NC - - Do not connect
C9 GND - - -
C10 VREG_L11_SDC2 SDC2 PO Power output for SD card pull up voltage;
C11 VREG_L13_3P3 3.3V PO 3.3V LDO power output,100mA
C12 GND - - -
C13 GPIO_61 1.8V IO Can be configured as GPIO
C14 GPIO_63 1.8V IO Can be configured as GPIO
C15 GPIO_65 1.8V IO Can be configured as GPIO
C16 GPIO_67 1.8V IO Can be configured as GPIO
C17 GND - - -
C18 GPIO_70 1.8V IO Can be configured as GPIO
C19 GPIO_72 1.8V IO Can be configured as GPIO
C20 GPIO_74 1.8V IO Can be configured as GPIO
C21 GPIO_76 1.8V IO Can be configured as GPIO
C22 GND - - -
C23 GPIO_22 1.8V IO Can be configured as GPIO
C24 GPIO_24 1.8V IO Can be configured as GPIO
nicholas.wang_thundercomm.com
2022-07-21 2:34:47 AM CST