- USER MANUAL - MANUEL DE L’UTILISATEUR - BENUTZERHANDBUCH - HANDLEIDING - MANUALE D’USO - MANUAL DEL USUARIO - MANUAL DO UTILIZADOR - РУКОВОДСТВО ПОЛЬЗОВАТЕЛЯ - ΕΓΧΕΙΡΙΔΙΟ ΧΡΗΣΗΣ - KULLANIM KILAVUZU - INSTRUKCJA OBSŁUGI
FOR XBOX ONE User Manual WARNING: To ensure that your TX Racing Wheel functions correctly with games for XBOX ONE, you may be required to install the games' automatic updates (available when your games console is connected to the Internet).
TECHNICAL SPECIFICATIONS 1 2 3 4 5 6 7 8 9 Racing wheel base Racing wheel 2 sequential gear shift levers (Up & Down) Multidirectional D-Pad Switch (3 positions) MODE button + Red/Green indicator light 12 Thrustmaster Quick Release 13 Controller pairing (for Kinect™ detection) 14 Mains supply connector (type A or B) (Varies from one country to another) Xbox Guide button White indicator light Large threaded hole (for attachment system and tightening screw) 10 Attachment system 11 Metal fastening screw 1
CONNECTING THE RACING WHEEL TO THE MAINS = PLEASE READ BEFORE PROCEEDING! Your racing wheel's power supply varies according to the country where you purchased your device. The mains supply can be: Internal, with: * A power supply unit located directly inside the racing wheel's base, with a type A connector *A 220-240V mains power supply cable = compatible only with a 220-240V electrical supply.
WARNINGS Before you use this product, please read this documentation carefully and keep it safe should you need to consult it later. Warning – Electric shock * Store the product in a dry location and do not expose it to dust or sunlight. * Respect the connection direction. * Do not twist or pull the connectors and cables. * Do not spill any liquid on the product or its connectors. * Do not short-circuit the product.
Warning – Injuries due to force feedback and repeated movements (suite) * If the symptoms or pain indicated above persist when you start playing again, stop playing and consult your doctor. * Keep out of children’s reach. * During games, always leave both hands correctly positioned on the steering wheel without completely letting go. * During gameplay, never place your hands or your fingers under the pedals or anywhere near the pedal set.
Warning – Pedal set pinch hazard when playing * Keep the pedal set out of children’s reach. * When playing, never place your fingers on or anywhere near the sides of the pedals. * When playing, never leave your fingers on or anywhere near the pedals' rear base. * When playing, never place your fingers on or anywhere near the pedals' front base. NEVER NEVER Warning – Pedal set pinch hazard when not playing * Store the pedal set in a safe place, and keep it out of children’s reach.
ATTACHING THE WHEEL TO ITS BASE Align the connector locations using the arrows: Base (1) connector: Arrow pointing upwards Racing wheel (2) connector: Arrow pointing upwards Once the connectors are correctly positioned, simply rotate the Thrustmaster Quick Release (12) device's ring counterclockwise, while holding the racing wheel (2) in position. Then, tighten the ring as much as you can; to do so, hold the ring in position and rotate the racing wheel clockwise.
ATTACHING THE RACING WHEEL Attaching the racing wheel to a table or a desktop 1. Place the racing wheel on a table or any other horizontal, flat and stable surface. 2. Insert the fastening screw (11) in the attachment system (10), then tighten the device by turning the screw counterclockwise, so that it feeds into the large threaded hole (9) located beneath the racing wheel, until the device is perfectly stable.
ATTACHMENT / REMOVAL DIRECTION To tighten: Turn the screw counterclockwise To release: Turn the screw clockwise 9/24
Attaching the racing wheel's base to a cockpit 1. Place the racing wheel's base on the cockpit shelf. 2. Drive two M6 screws (not included) through the cockpit shelf, then feed them into the two small threaded holes located beneath the racing wheel. Important: The length of the M6 screws should not exceed the thickness of the shelf + 12 mm; longer screws could cause damage to internal components located in the racing wheel's base. 3.
UPGRADING YOUR RACING WHEEL'S FIRMWARE The firmware included in your racing wheel's base can be upgraded to a more recent version featuring product enhancements. To display the firmware version that your racing wheel is currently running and upgrade it if required: on PC, connect to http://ts.thrustmaster.com. In the Updates and downloads section, click Xbox One / Wheels / TX Racing Wheel, then select Driver / Firmware and follow the instructions describing the download and setup procedure.
If your racing wheel and pedal set do not operate correctly, or if calibration seems incorrect: Turn off your console, disconnect your racing wheel entirely, reconnect all cables (using the mains power supply cable and pedal set), then restart your console and your game. CONTROLLER PAIRING (13) To ensure correct detection of your racing wheel, the device's controller pairing (located on the upper section of the racing wheel's base) must always remain in the KINECT™ camera's field of vision.
MODE BUTTON AND INDICATOR LIGHT (6) MODE button for the pedal set You can electronically swap the accelerator and clutch pedals. To do so, simply press the MODE button (6) for 2 seconds. The racing wheel's internal memory stores whether the pedals have been swapped around or not. ACCELERATOR AND CLUTCH PEDALS Color of the MODE indicator light (6) NORMAL RED SWAPPED AROUND GREEN Other hints for the MODE button To learn more about MODE button and indicator light, please visit http://ts.thrustmaster.
14/24
TECHNICAL FEATURES 1 Metal support for conical stop (not installed by default) 2 Conical stop 3 Attachment screw for metal support 4 2.
WARNING Before using this product, be sure to read these instructions carefully and save them for future reference. For safety reasons, never use the pedal set with bare feet or while wearing only socks on your feet. THRUSTMASTER® DISCLAIMS ALL RESPONSIBILITY IN THE EVENT OF INJURY RESULTING FROM USE OF THE PEDAL SET WITHOUT SHOES. Warning – Pedal set pinching hazard during gaming sessions * * * * Keep the pedal set out of the reach of children.
AUTOMATIC CALIBRATION OF PEDALS IMPORTANT: - Never connect or disconnect the pedal set from the base of the wheel when the wheel is connected to the console or PC, or during gaming sessions, to avoid calibration problems. = Always connect the pedal set to the wheel before connecting the wheel to the console or PC. - Once the wheel has self-calibrated and the game has started, the pedals automatically calibrate themselves after being pressed a few times.
ADJUSTING THE PEDAL SET Each of the three pedals includes: - A metal head (8) with multiple perforations (nine for the accelerator – six for the brake – six for the clutch). - A plastic head support (7) (placed between the head and the arm) with four perforations. - A pedal arm (6) with two perforations. ATTENTION: To avoid any calibration problems, be sure to always disconnect your wheel’s USB cable from the console or PC before making any adjustments to your pedal set.
Adjusting the SPACING of the three pedals - Using the included 2.5 mm Allen key (4), unscrew the two screws holding the metal head (8) and its support (7) in place. - Select your preferred position (to the left, centered, or to the right), then replace and re-tighten the screws so that the metal head (8) and its support (7) are held firmly in place.
Installing the conical stop (“CONICAL RUBBER BRAKE” mod) This modification (or “mod”) is not essential, and is not installed by default. This means that the brake pedal functions perfectly even if the mod is not installed. This mod lets you experience a different feeling and resistance when braking. It’s up to you whether or not to install it, depending on your own preferences. - Screw the conical stop (2) onto its metal support (1).
- Using the included 2.5 mm Allen key (4), attach the unit using the attachment screw (3) and the small central screw thread located on the underside of the pedal set.
CONSUMER WARRANTY INFORMATION Worldwide, Guillemot Corporation S.A., whose registered office is located at Place du Granier, B.P. 97143, 35571 Chantepie, France (hereinafter “Guillemot”) warrants to the consumer that this Thrustmaster product shall be free from defects in materials and workmanship, for a warranty period which corresponds to the time limit to bring an action for conformity with respect to this product.
Additional warranty provisions During the warranty period, Guillemot shall not provide, in principle, any spare parts, as Technical Support is the only party authorized to open and/or recondition any Thrustmaster product (with the exception of any reconditioning procedures which Technical Support may request that the consumer carry out, by way of written instructions – for example, due to the simplicity and the lack of confidentiality of the reconditioning process – and by providing the consumer with the re
COPYRIGHT © 2017 Guillemot Corporation S.A. All rights reserved. Thrustmaster® is a registered trademark of Guillemot Corporation S.A. All other trademarks are the property of their respective owners. Illustrations not binding. Contents, designs and specifications are subject to change without notice and may vary from one country to another. Made in China. FCC STATEMENT 1. This device complies with Part 15 of the FCC Rules.
