Kitchen Island
PART LIST Front Top Rail Left Panel 1 PC 1 PC 1 PC 1 PC 1 PC Back Top Rail Front Middle Rail Back Bottom Rail Bottom Panel 1 PC 1 PC 1 PC 1 PC Left Partition Panel 1 PC Back Partition Panel 2 PCS Back Panel Adjustable Shelf 3 PCS 2 PCS Right Partition Panel 1 PC Top Vertical Panel 1 PC Middle Adjustable Shelf 1 PC Drawer Front Panel 2 PCS Drawer Bottom Panel 2 PCS Left Door Panel 2 PCS Right Panel Back Top Panel Top Panel Drawer Left Panel Drawer Right Panel Drawer Back Panel
PART LIST Leg 4 PCS 3
HARDWARE LIST #1 #2 #3 #4 08*030mm #5 2"*01/4"*011 mm Cam Lock Cam Bolt Wood Dowel Long Bolt 17 PCS (Extra 2) 17 PCS 45 PCS (Extra 1) 8 PCS #6 #7 #8 #9 i 1"* q; 4*08mm Screw 16 PCS (Extra 1) #10 3/4 "* q; 5/32"*09mm Barrel Nut Shelf Holder 8 PCS 12 PCS #11 #12 Knob #13 6 PCS Round Head Bolt #14 6 PCS 12mm* q; 3*06mm Double Magnet Magnet 1 PC 2 PCS #16 #17 Round Head Screw 6 PCS (Extra 1) #18 Large Round Head Screw 16 PCS (Extra 1) #15 1-1/4"*(/;4*08mm Allen Wr
Step 1. Insert cam bolts (part #2) into top panel (part A), left panel (part B) and right panel (part C) using phillips head screwdriver. NOTE: Do not overtighten cam bolts. Stop tightening once threads on cam bolt are no longer visible. #2 x17 Step 2. Attach knobs (part #8) to drawer front panels (part Q) and door panels (parts V & W) using round head bolts (part #9) and phillips head screwdriver.
Step 3. Attach front top rail (part E) to top vertical panel (part L) using wood dowel (part #3), long screw (part #15) and phillips head screwdriver. With front top rail (part E) flat on ground, attach front middle rail (part G) and back top rail (part F) to top vertical panel (part L) using wood dowels (part #3), long screws (part #15) and phillips head screwdriver. NOTE: Please ensure screws are aligned with the pre-drilled holes in top vertical panel (part L) before tightening.
Step 5. Attach back partition panels (part M) to back top panel (part D) using wood dowels (part #3). Slide back panels (part N) into grooves of right panel (part C), back top panel (part D) and back partition panels (part M). #3 x4 Step 6. Attach back bottom rail (part H) to back partition panels (part M), back panels (part N) and right panel (part C) using wood dowels (part #3) and cam lock (part #1 ). NOTE: Cam locks must rotate a full 180 ° . See pictured insert.
Step 7. Attach left panel (part B) to assembled unit (parts D, E, F, G, H & N) using wood dowels (part #3) and cam locks (part #1 ). NOTE: Cam locks must rotate a full 180 ° . See pictured insert. point arrow o lock to ward adjace B N 1/2 turn clockwise to fasten #1 # N #1 &!?x6 #3 x5 Step 8. Attach double magnet (part #11) and magnets (part #12) to front middle rail (part G) using round head screws (part #13) and phillips head screwdriver.
Step 9. Attach bottom panel (part I) to assembled unit (parts B, C, H, J & K) using wood dowels (part #3), long bolts (part #4 ), barrel nuts (part #6) and allen wrench (part #14 ) . .,,,..,,-----... '' \ \ \ \ I I I I I I / / I I I B C #3 #4 #6 I x10 i x8 rnx 8 #14 '>x1 Step 10. CASTER INSTALLATION Attach locking casters (part X) and casters (part Y) to bottom panel (part I) using large round head screws (part #10) and phillips head screwdriver. # ,,, / \ \ #10 #1wf10 xi A\-n· I
Step 11. LEG INSTALLATION Attach adjustable levelers (part #19) to legs (part Z). Attach legs (part Z) to bottom panel (part I) using wood dowels (part #3), flat washers (part #17), spring washers (part #18), short bolts (part #16) and allen wrench (part #14 ). -----#3 x8 #14":>x1 # 1 6 , x4 #17 ® x4 #18 o x4 #19 Y x4 Step 12. Carefully turn unit upright.
Step 13. Attach top panel (part A) to assembled unit (parts B, C, D, E & L) using wood dowels (part #3) and cam locks (part #1 ). NOTE: Cam locks must rotate a full 180 ° . See pictured insert. 1/2 turn clockwise to fasten #1 &;>xs #3 x2 Step 14. Attach door panels (parts V & W) by placing bottom pin hinge (pre-installed in door) in the pre-drilled hole of bottom panel (part I). Then depress the top spring-loaded pin hinge so it can be placed in the pre-drilled hole of front middle rail (part G).
Step 15. Slide assembled drawers into place. Slide adjustable shelves (part 0) and middle adjustable shelf (part P) into place.
