5-Shelf Bookcase
Table of Contents Part Identification Hardware Identification Assembly Steps Assembly Tools Required 3 No. 2 Phillips Screwdriver Tip Shown Actual Size 4 5-16 Hammer Français 17-18 Español 19-20 Safety 21-22 Warranty Page 2 Not actual size Skip the power trip. This time.
Now you know our ABCs. Part Identification å While not all parts are labeled, some of the parts will have a label or an inked letter on the edge to help distinguish similar parts from each other. Use this part identification to help identify similar parts.
Hardware Identification å Screws are shown actual size. You may receive extra hardware with your unit.
Look for this icon. It means a video assembly tip is available at www.sauder.com/services/tips Step 1 å Assemble your unit on a carpeted floor or on the empty carton to avoid scratching your unit or the floor. å Push eight HIDDEN CAMS (1F) into the SIDE SKIRTS (M and N) and SKIRTS (L). Then, insert the metal end of a CAM DOWEL (2F) into each HIDDEN CAM. Do not tighten the HIDDEN CAMS in this step. Lx2 Arrow N Arrow M Insert the metal end of the CAM DOWEL into the HIDDEN CAM.
Step 2 å Push thirty HIDDEN CAMS (1F) into the holes of the TOP SHELVES (B, C, D, E, and F) and BACKS (G). Arrow F 1F (30 used) E C D B Gx5 Arrow Hole The arrow in the HIDDEN CAM must point toward the hole in the edge of the board.
Step 3 å Turn thirty CAM SCREWS (8F) into the LEGS (H, I, J, and K). 8F (30 used) These holes will not have CAM SCREWS. K I H J These holes will not have CAM SCREWS.
Step 4 å Fasten the SKIRTS (M and N) to the LEGS (H, I, J, and K). Use eight SILVER 1-1/8" FLAT HEAD SCREWS (10S). å NOTE: Start each screw a few turns before completely tightening any of them. Some assembly (and snacks) required. 10S SILVER 1-1/8" FLAT HEAD SCREW (8 used in this step) Surface with HIDDEN CAMS must be facing up.
Step 5 å Insert five METAL PINS (1R) into the holes shown in the RIGHT REAR LEG (J). å Fasten the BACKS (G) to the RIGHT REAR LEG (J). Tighten five HIDDEN CAMS. å NOTE: Be sure the METAL PINS (1R) in the LEG (J) insert into the holes in the ends of the BACKS (G). å Insert five METAL PINS (1R) into the smaller holes in the BACKS (G). 1 2 1R The HIDDEN CAMS are closer to this edge.
Step 6 å Fasten the SHELVES (B, C, D, E, and F) to the LEGS (H and J). Tighten ten HIDDEN CAMS.
Step 7 å å NOTE: You may need someone's help in this step. å NOTE: Be sure the METAL PINS (1R) in the ends of the BACKS (G) insert into the holes in the LEGS (I and K). Fasten the LEGS (I and K) to the SHELVES (B, C, D, E, and F) and BACKS (G). Tighten fifteen HIDDEN CAMS.
Step 8 å Fasten the BACKS (G) to the SHELVES (B, C, D, E, and F). Use ten BLACK 1-1/4" FLAT HEAD SCREWS (74S). å NOTE: There are no pre-drilled holes in the back of the SHELVES (B, C, D, E, and F). Use extra force when turning these screws. If you're doing this to help a friend, don't leave without a bite.
Step 9 å Open the FURNITURE TIPPING RESTRAINT KIT (97) and fasten the SAFETY STRAP to the TOP (A2). Use the provided BLACK 9/16" LARGE HEAD SCREW. å å NOTE: Position the SAFETY STRAP exactly as shown. BLACK 9/16" LARGE HEAD SCREW (1 used in this step) Fasten the TOP (A2) to the SIDE SKIRTS (M and N). Tighten four HIDDEN CAMS. Safety strap M A2 A2 Sur fac ew ith one hol e Safety strap Surface with holes N 97 Caution Risk of damage or injury. HIDDEN CAMS must be completely tightened.
Step 10 å Fasten the SKIRTS (L) to the TOP (A2) and BOTTOM (F). Tighten four HIDDEN CAMS.
Step 11 å Center a SCREW COVER (74P) over the head of each SILVER SCREW in the SIDE SKIRTS (M and N) and gently tap in with your hammer. å Using your hammer, gently tap a CAM COVER (75P) onto each HIDDEN CAM except on the bottom of the SHELF (F) and lower SKIRT (L) as noted below. M N L 74P F (8 used) To cover SILVER screws 75P (32 used) To cover HIDDEN CAMS Do not cover HIDDEN CAMS here.
Step 12 å å Carefully stand your unit upright in its final location. We recommend using the SAFETY STRAP for added stability. å INSTALLATION INSTRUCTIONS: 1. Insert the SAFETY DRYWALL ANCHOR through the WASHER and the end of the SAFETY STRAP. 2. Using a Phillips screwdriver or a hand drill, press the screw slightly onto the drywall. 3. Apply pressure; turn the screw until a pilot hole is made and the nylon sheath slips through. 4.
Bibliothèque avec 5 Tablettes Utilisez les instructions d’assemblage en français avec les schémas étape par étape du manuel d’instruction en anglais. Chaque étape en français correspond à la même étape en anglais. La pièce devant être attachée à l’élément est représentée en gris sur les schémas de chaque étape pour plus de précision. Comparer la “Liste de pièces” ci-dessous avec la “PART IDENTIFICATION” du manuel en anglais pour vous familiariser avec les pièces avant l’assemblage.
ÉTAPE 1 ÉTAPE 8 Ne pas serrer les EXCENTRIQUES ESCAMOTABLES dans cette étape. Assembler l'élément sur un sol à moquette ou sur le carton vide pour éviter d'endommager l'élément ou le sol. Enfoncer huit EXCENTRIQUES ESCAMOTABLES (1F) dans les PLINTHES LATÉRALES (M et N) et les PLINTHES (L). Ensuite, insérer l'extrémité en métal de la CHEVILLE D'EXCENTRIQUE (2F) dans chaque EXCENTRIQUE ESCAMOTABLE. Fixer les ARRIÈRES (G) aux TABLETTES (B, C, D, E et F). Utiliser dix VIS TÊTE PLATE 32 mm NOIRES (74S).
Librería con 5 Estantes Use estas instrucciones de ensamblaje en español junto con las figuras paso-a-paso provistas en el folleto inglés. Cada paso en español corresponde al mismo paso en inglés. Se destacan las figuras de cada paso con una tonalidad oscura para mostrar precisamente cual parte se debe montar a la unidad. Compare la “Lista de Part” abajo con la “Part Identification” en el folleto en inglés para familiarizarse con Las partes de ensamblaje.
PASO 1 PASO 8 No apriete los EXCÉNTRICOS ESCONDIDOS en este paso. Ensamble la unidad sobre un piso alfombrado o sobre el cartón vacío para evitar rayar la unidad o el piso. Empuje ocho EXCÉNTRICOS ESCONDIDOS (1F) dentro de los FALDONES LATERALES (M y N) y de los FALDONES (L). A continuación, inserte el extremo de metal de un PASADOR DE EXCÉNTRICO (2F) dentro de cada EXCÉNTRICO ESCONDIDO. Fije los DORSOS (G) a los ESTANTES (B, C, D, E y F). Utilice diez TORNILLOS NEGROS DE CABEZA PERDIDA de 32 mm (74S).
WARNING Please use your furniture correctly and safely. Improper use can cause safety hazards, or damage to your furniture or household items. Carefully read the following chart. Look out for: What can happen: How to avoid the problem: • Overloaded shelves. • Improper loading can cause the product to be top-heavy. • Risk of injury. • Top-heavy furniture can tip over. • Overloaded shelves can break. • Never exceed the weight limits shown in the instructions.
ADVERTENCIA Por favor use el mobiliario correcta y seguramente. El mal uso puede causar riesgos de seguridad o daño a las unidades o artículos domésticos. Cuidadosamente lea la tabla a continuación. Esté alerto de: Puede ocurrir: Evitar el problema: • Estantes sobrecargados • Cargar el producto inadecuadamente puede causar la inestabilidad. • Riesgo de lesiones. • El mobiliario inestable puede volcarse. • Estantes sobrecargados pueden romper.
5-YEAR LIMITED WARRANTY 1. Woodworking Co. (Sauder®) provides limited warranty coverage to the original purchaser of this product for a period of fi ve years from the date of purchase against defects in materials or workmanship of Sauder furniture components. As used in this Warranty, “defect” means imperfections in components which substantially impair the utility of the product. This Warranty gives you specifi c legal rights, and you may also have other rights which vary from state to state. 2.
