ENTRYWAY STORAGE BENCH 1/13
DO NOT RETURN FOR REPLACEMENT PARTS OR OTHER INQUIRIES PLEASE CONTACT US PLEASE ENSURE TO HAVE THE MODEL # FROM THE PACKAGING OR INSTRUCTION BOOKLET 2/13
IMPORTANT : Please read this manual carefully before beginning assembly of this product. Keep this manual for future reference. SAFETY INFORMATION Identify all the parts and hardware. Do not discard of the packaging until you have checked that you have all of the parts and hardware required. Hardware package may have spare parts. WARNING: This item contains small parts which can be swallowed by children and pets. Keep children and pets away during assembly.
PRE-ASSEMBLY INFORMATION PARTS DESCRIPTION B A SIDE QTY 1 PAIR SEAT QTY 1 C D BACK QTY 1 FRONT QTY 1 F This Side Up E DIVIDER QTY 1 BACKREST QTY 1 G H BOTTOM PANEL QTY 1 BOTTOM SUPPORT LEG QTY 1 NEED HELP? For help with assembly or if you are missing a part, Please call customer service 4/13
PRE-ASSEMBLY INFORMATION HARDWARE DESCRIPTION 2 1 CAM LOCK PIN CAM LOCK QTY 4 SET ALLEN KEY SCREW M6 x 30 mm QTY 12 4 3 5 6 PHILLIPS SCREW ROUND HEAD M4 X 15 mm QTY 4 ALLEN KEY QTY 1 7 8 PHILLIPS SCREW M4 X 30 mm QTY 4 WOOD DOWEL 8 X 30 mm QTY 10 PHILLIPS SCREW M4 X 15 mm QTY 6 9 ALLEN KEY BOLT M6 x 50 mm QTY 4 LID SUPPORT QTY 1 10 WOOD BOLT CAP QTY 4 Required Flathead screwdriver Phillips screwdriver Not Included NEED HELP? For help with assembly or if you are missing a part, Please ca
COMPONENTS – KEY DIAGRAM 6/13
ASSEMBLY This Side Up STEP 1 1. Attach 2 Cam Lock Pins 2 to Back D into guide holes. 2. Align and insert Cam Lock Pins on Back D into pre-drilled holes on Dividers E . ( Note: please pay close attention to the location of the 2 small guide holes which accommodate the lid support. They need to be on the same side as the holes of cross hinges ). 3. Place 2 Cam Locks 2 into pre-drilled holes on Dividers E . 4. Use a flathead screwdriver to tighten Cam Locks into Pins.
ASSEMBLY This Side Up This Side Up STEP 2 1. Attach Bottom Panel G to Divider E & Back D by sliding on the gap between Divider E & the long rail on Back D .
ASSEMBLY This Side Up STEP 3 1. Attach 2 Cam Lock Pins 2 to Front C into guide holes. 2. Align and insert Cam Lock Pins on Front C into pre-drilled holes on Dividers E . 3. Place 2 Cam Locks 2 into pre-drilled holes on Dividers E . 4. Use a flathead screwdriver to tighten Cam Locks into Pins.
ASSEMBLY STEP 4 1. Insert 5 Dowels 3 into each Side B at specified location. 2. Align pre-drilled holes on side bars of Front C & Back D and Backrest F with Dowel 3 on Sides B . 3. Attach Front C & Back D to Sides B using 12 Allen Key Screws 1 through predrilled holes ( 6 Screws / each Side B ). 3. Attach Backrest F to Sides B using 4 Allen Key Bolts 8 through pre- drilled holes ( 2 Screws / each Side B ). 4. Use Allen Key 4 to tighten Screws. Do not over-tighten.
ASSEMBLY STEP 5 NOTE: The screwdriver is not included in the hardware pack. 1. Attach Bottom Support Leg H into pre-drilled holes of Bottom Panel G using 4 Phillips Screws 7 . 2. Use Phillips screwdriver to tighten Screws. Do not over-tighten. STEP 6 1. Attach Seat A to Back D using 6 Phillips Screws 6 ( using guide holes on bar of Back ). 2. Use phillips screwdriver to tighten Screws. Do not over-tighten.
ASSEMBLY STEP 7 1. Attach Lid Supports 9 into pre-drilled holes of Seat B and Divider E using Phillips Screws Round Head 5 . 2. Use phillips screwdriver to tighten Screws. Do not over-tighten. STEP 8 1. Insert 4 Wood Bolt Caps 10 into exposed bolt holes on side of bench.
WARRANTY Thank you for purchasing our product. These products have been made to demanding, high-quality standards and are guaranteed for domestic use against manufacturing faults for a period of 12 months from the date of purchase. This warranty does not affect your statutory rights. In case of any malfunction of your product (failure, missing parts, etc.) please contact us at our toll free service line or by email We reserve the right to repair or replace the defective product, at its discretion.
