Assembly Instructions

ManualsBrandsThree Posts ManualsBar FurnitureBenally Home Bar

IMPORTANT NOTE

Carefully remove all the parts from the carton and put

them individually on a soft cloth to prevent scratches

or other damage occurring to the parts.

We have taken great care in the design of this

product and request that you carefully and strictly

follow our assembly instructions to ensure a

completed product as it was designed.

Part List

Glass Holder

1 Pc.

Top

1 Pc.

Front Panel

1 Pc.

Front Panel

2 Pcs.

Door

1 Pc.

Sub Top

1 Pc.

Front Panel

1 Pc.

Bar

Summary of content (7 pages)

PAGE 1
Bar IMPORTANT NOTE Carefully remove all the parts from the carton and put them individually on a soft cloth to prevent scratches or other damage occurring to the parts. We have taken great care in the design of this product and request that you carefully and strictly follow our assembly instructions to ensure a completed product as it was designed. Part List A. Top 1 Pc. B. Sub Top 1 Pc. E. Glass Holder 1 Pc. C. Front Panel 1 Pc. H. Front Panel 2 Pcs. I. Front Panel 1 Pc. N. Door 1 Pc.
PAGE 2
Bar IMPORTANT NOTE Carefully remove all the parts from the carton and put them individually on a soft cloth to prevent scratches or other damage occurring to the parts. We have taken great care in the design of this product and request that you carefully and strictly follow our assembly instructions to ensure a completed product as it was designed. Part List M. Base 1 Pc. F. Front Rail 1 Pc. O. Shelf 3 Pcs. P. Foot Rest Support 3 Pcs. D. Side Panel 2 Pcs. G. Front Rail 1 Pc. Q. Foot Rest 1 Pc. J.
PAGE 3
Assembly Instructions 2/6 IMPORTANT * Please keep Hex Wrench in a safe place as you may need to tighten up the Head Cap Bolts in the future. * Do not tighten up all the bolts until each part is properly assembled. * Use a soft cloth between these parts and the floor. * After assembly item must be level to work properly. Use the included adjustable levelers to level.
PAGE 4
Assembly Instructions 3/6 H I H STEP 3 Attach Front Panels (H) to Front Panel (I) with Cam Locks. F G L J K Magnet Wood Screw for Magnet M STEP 4 Attach Magnet to Front Rail (G) with Wood Screws for Magnet. (See Figure 2) Attach Side Panel (J) and (K) to unit from Step 3, then attach unit to Base (M) with Cam Locks. Attach Front Rails (F) and (G) and Middle Panel (L) to unit with Cam Locks.
PAGE 5
Assembly Instructions 4/6 Figure 3 E R Flat Washer Head Cap Bolt N O O O Adjustable Pin Figure 4 STEP 5 Insert Adjustable Pins into side panels and middle panel at the desired level. Slide Shelves (O) into position. Attach top unit to body unit with Cam Locks, then attach Glass Holder (E) to unit with Head Cap Bolts and Flat Washers. Attach Pull Handle to Door (N) with Machine Screw. (See Figure 3) Attach Door (N) to unit by sliding the door lift hinges into the side panel lift hinges.
PAGE 6
Assembly Instructions 5/6 Same amount of Foot Rest (Q) on each side Tapered Wood Screw P P P Q STEP 6 Head Cap Bolt (short) Slide Foot Rest (Q) into the Foot Rest Supports (P). Attach Foot Rest Supports (P) to unit at the pre-drilled holes with Tapered Wood Screws. Figure 5 Attach Foot Rest (Q) to Foot Rest Supports (P) with Head Cap Bolts (short), leaving the same amount of Foot Rest (Q) protruding on the outside of the outer Foot Rest Supports (P).
PAGE 7
Assembly Instructions 6/6 Drawer R R1 STEP 1 R3 R2 Attach Side Part R3 to Front Part (R1) and Back Part (R2) using a Phillips screwdriver and long wood screws (4X), tighten halfway. (See Figure 1) Figure 1 MAKE SURE ROLLER IS ON THE BACK R4 STEP 2 R5 Insert Base Part (R5) into the groove. Attach Side Part (R4) to Front Part (R1) and Back Part (R2) using a Phillips screwdriver and long wood screws (4X). (See Figure 2) Figure 2 Tighten all wood screws used in drawer assembly.