Assembly Instruction Sheet

Package Contents
Warnings and Cautions
1of2
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly
recommend that a licensed, professional electrician perform the installation.
Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal. Do not subject
glass parts to any shock while in operation or shattering may result.
A
(1)MediumBaseDecorativeFilament60Wbulb(provided),Maximum100W,Alternatebulb(1)23WCFLMaximum.
30-45minutes
Identifyandinspectallpartsbeforebeginninginstallation.Checkpackagecontentlistanddiagramsbelowtobesureallpartsare
present.Ifanypartsaremissingordamaged,donotattempttoassemble,install,oroperatethefixture.Contactcustomerserviceforreplacement
parts.
C
Fixture
Body
x1
Shade
x1
D
Edison
Bulb
x1
Socket Collar
x1
B
Hardware Contents
AA
Crossbar
x1
Mounting
Ball
x2
BB
Mounting Screw
x2
DD
Lock Washer
x2
Hex Nut
x2
CC
EE
Alternate Mounting
screw
x2
FF
STEP 1 - Install Mounting Screws and Crossbar
A. Screw Mounting Screws (BB) or Alternate Short Mounting Screws
(FF) into the Crossbar (AA), place Lock Washers (CC) over Mounting
Screws (BB) or Alternate Short Mounting Screws (FF) and thread
Hex Nuts (DD) onto Mounting Screws (BB) or Alternate Short
Mounting Screws (FF) as shown. Secure positions of Mounting
Figure 1
Outlet
Box
Outlet Box
Screw (not
included)
Green Ground
Screw
AA
DD
CC
Mounting Screw
or Alternate Short
Mounting Screw
STEP 2 Fit Backplate to
Mounting Screws
-
A. on Fixture Body
(A) to Mounting Screws
Fit the backplate
(BB) or
Alternate Short Mounting Screws
(FF) and secure with Mounting
Balls (EE). Note: The backplate
should be
snug against the wall and the
Mounting Balls (EE). If
on Fixture Body (A)
not,
adjust the length of Mounting
Screw (BB) or Alternate Short
Mounting Screw (FF) by
Figure 2
A
Hex Nut and
Lock Washer
Backplate
Mounting Screw
or Alternate Short
Mounting Screw
EE
AA
unscrewing Hex Nuts (DD) and Lock Washer (CC) and then
screwing Mounting Screw (BB) or Alternate Short Mounting Screw
(FF) in or out of the Crossbar (AA) until the correct length is
achieved. Once the backplate on Fixture Body (A) is secure, remove
Mounting Balls (EE) and Fixture Body (A) and proceed to Step 3.
STEP 3 - Wire Connections
A. Use standard wire connectors (not included) to make all wire
connections. (Connectors are not included with fixture.) Twist
connectors until wires are tightly joined together. Wrap each
connection with approved electrical tape and carefully stuff all the
connected wires into the Outlet Box.
White wire
from supply
White wire
from fixture
Black wire from
supply (or Red)
Black wire
from fixture
Ground wire
from supply
Ground wire
from fixture
Figure 3
STEP 4 Install Fixture Body-
A. Carefully tuck all wires into the
outlet box and position the
backplate of Fixture Body (A)
over the outlet box. Align the
holes in the backplate with
Mounting Screws (BB) or
Alternate Short Mounting
Screws (FF). Secure with
Mounting Balls (EE) and hand
tighten until snug.
Figure 4
A
Mounting Screw
or Alternate Short
Mounting Screw
Back Plate
EE
AA
Screws (BB) or Alternate
Short Mounting Screws
(FF) by tightening Hex
Nuts (DD) against the
Crossbar.
B. Secure the Crossbar (AA)
to the Outlet Box with
Outlet Box Screws (not
included).
Assembly Instruction Sheet
ToolsRequired:
LightSource:
EstimatedAssembly Time:
Preparation:
Flatheadscrewdriver,Phillipsscrewdriver,pliers,wirecutters,wirestrippers,electricaltape,safetyglasses.
Thank you for purchasing a product.
Need assistance with parts or assembly? Call customer service.