Installation Guide

ManualsBrandsThree Posts ManualsBathroom Vanity LightingBima 2-Light Vanity Light

Package Contents

1of2

Crossbar Assembly

(2)A19MediumBaseBulbs100WMaximum,bulbsnotincluded.

20-30minutes

Identifyandinspectallpartsbeforebeginninginstallation.Checkpackagecontentlistanddiagramsbelowtoensureallpartsare

present.Ifanypartsaremissingordamaged,donotattempttoassemble,install,oroperatethefixture.Contactyouroriginalplaceofpurchase.

LightSource:

EstimatedAssembly Time:

Preparation:

ToolsRequired:Flatheadscrewdriver, Phillips screwdriver,pliers,wirecutters,wirestrippers,electricaltape,safetyglasses.

STEP 1 - Installing the Crossbar Assembly

A. Attach the Crossbar Assembly (A) to the outlet box with the head

of the green ground screw facing you. Secure the Crossbar

Assembly (A) with outlet box screws (not included). Tighten until

snug

Note: Use the Alternate Shorter Mounting Screw (B) if your

installation requires a shorter mounting screw.

Fixture Body

Warnings and Cautions

Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.

These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly

recommend that a licensed, professional electrician perform the installation.

Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal.

Glass Shade

Socket Collar

Figure 1

Alternate

Mounting screw

Outlet Box Screws

(not included)

Outlet Box

Mounting Screw

or Alternate Short

Mounting Screw

STEP 2 Test Fit the Backplate to the Crossbar Assembly-

A. Remove the mounting balls from the Crossbar Assembly (A). Place

the backplate and Fixture Body (C) onto the Crossbar Assembly (A)

and secure with mounting balls. Note: The backplate and Fixture

Body (C) should be snug against the wall and held tight with the

mounting balls. If it is not, adjust the length of the mounting screws

or alternate short mounting screws on the Crossbar Assembly (A) by

unscrewing the preassembled hex nut and lock washer and then

Backplate

Mounting Screw

or Alternate Short

Mounting Screw

Mounting Ball

(Step 2 Continued)

screwing the mounting screws or alternate short mounting screws in

or out of the crossbar until the correct length is achieved. Once the

backplate and Fixture Body (C) is secure, remove the mounting ball

and Fixture Body (C).

Figure 2

STEP 3 - Wire Connections

A. Wrap bare or green ground wire around green ground screw on the

crossbar, no less than 2 inches from the end of the wire. Tighten the

green ground screw.

B. Use standard wire connectors (not included) to make all wire

connections. Twist connectors until wires are tightly joined together.

Wrap each connection with approved electrical tape and carefully

stuff all the connected wires into the Outlet Box.

Figure 3

Green Ground Screw

on the Crossbar

White wire

from outlet box

White wire

from fixture

Black wire from

outlet box (or Red)

Black wire

from fixture

Bare, or Green

Ground wire

from outlet box

Ground wire

from Fixture

Hex Nut and

Lock Washer

Installation Guide

Summary of content (2 pages)

PAGE 1
Installation Guide Tools Required: Flathead screwdriver, Phillips screwdriver, pliers, wire cutters, wire strippers, electrical tape, safety glasses. Light Source: (2) A19 Medium Base Bulbs 100W Maximum, bulbs not included. Estimated Assembly Time: 20-30 minutes Preparation: Identify and inspect all parts before beginning installation. Check package content list and diagrams below to ensure all parts are present.
PAGE 2
STEP 4 - Install the Fixture Body STEP 5 - Install Glass Shade and Bulb A. Place the backplate of the Fixture Body (C) onto mounting screws or alternate short mounting screws and secure with previously removed mounting ball. Hand tighten until snug. A. Place the Glass Shade (D) over the socket and secure with the Socket Collar (E). Hand tighten until snug. B. Insert bulbs onto sockets and screw snugly into properly. Your fixture is now assembled and ready to use.