ENTRYWAY STORAGE CABINET 1/19
Questions, problems, assembly help, missing parts? No need to return the product, we will gladly help and ship your replacement parts free of charge Please call Customer Service In order to assist you in a timely manner, please have the following information ready: Model # _______________________ Part Number or Letter_______________________ Purchased at ___________________Date of Purchase ___________________________ If you wish to return the product, please contact the retailer where the product was purch
IMPORTANT : Please read this manual carefully before beginning assembly of this product. Keep this manual for future reference. SAFETY INFORMATION CAUTION: Injuries and damage can occur from furniture tip over if product is not properly anchored to the wall. Use the Furniture Anti-Tipping Restraint provided with the product. Consult our assembly instructions for help.
IMPORTANT : Please read this manual carefully before beginning assembly of this product. Keep this manual for future reference. CARE and MAINTENANCE Perhaps the greatest environmental damage to wood furniture comes from wide swings in relative humidity (RH) in our homes. Wood absorbs and desorbs water as relative humidity rises and falls, and in doing so it swells and shrinks. Making matters worse, it expands and contracts unequally along different grain directions.
PRE-ASSEMBLY INFORMATION PARTS DESCRIPTION A BL BR Fro nt / Ava nt Fro nt / Ava nt nt Ava nt / Fro TOP QTY 1 C LEFT SIDE QTY 1 RIGHT SIDE QTY 1 E D Fro nt / Ava nt Fro nt / Ava nt Fro nt / Ava nt Fro nt / Ava nt SMALL DIVIDER QTY 1 LARGE DIVIDER QTY 1 F G MIDDLE FRAME QTY 1 H Fro nt / Ava nt BOTTOM SHELF QTY 1 CABINET SHELF QTY 2 DOOR (L&R Same) QTY 2 NEED HELP? For help with assembly or if you are missing a part, Please call customer service 5/19
PRE-ASSEMBLY INFORMATION PARTS DESCRIPTION J IR IL L KR KL LEFT DRAWER SIDE QTY 2 DRAWER FRONT QTY 2 RIGHT BACK QTY 1 LEFT BACK QTY 1 RIGHT DRAWER SIDE QTY 2 DRAWER BACK QTY 2 M DRAWER BOTTOM QTY 2 NEED HELP? For help with assembly or if you are missing a part, Please call customer service 6/19
PRE-ASSEMBLY INFORMATION HARDWARE DESCRIPTION 1 2 ALLEN KEY SCREW M6 X 30 mm QTY 26 5 WOOD DOWEL Ø8 X 30 mm QTY 16 CAM LOCK PIN CAM LOCK QTY 16 SETS 6 7 PHILLIPS SCREW ROUND HEAD M4 X 15 mm QTY 21 9 4 3 SHELF SUPPORT QTY 12 8 PHILLIPS SHORT SCREW PHILLIPS MEDIUM SCREW M3 X 12 mm M3 X 15 mm QTY 12 QTY 8 11 10 ALLEN KEY QTY 1 12 a. b. c.
COMPONENTS – KEY DIAGRAM Fron t/A van t IL Fron t/A van t Fron t/A van t IR Fron t / Av ant BL BR H H Fron t/A van t Fron t/A van t Fron t/A van t KR KL 8/19
ASSEMBLY STEP 1 KR KL J 1. Attach 4 Cam Lock Pins 2 to back of Drawer Front J . 2. Align Cam Lock Pins with pre-drilled holes and attach Drawer Sides KL , KR . 3. Insert 2 Cam Locks 2 into pre-drilled holes on each Drawer Side KL , KR . 4. Use flathead screwdriver secure Cam Locks. STEP 2 M KR J KL 1. Slide Drawer Bottom M firmly into slots on Drawer Sides KL , KR and Drawer Front J .
ASSEMBLY STEP 3 L KR M KL 1. Align Drawer Back L with Drawer Bottom M and press firmly into slot . 2. Attach back using 2 Allen Key Screws 1 through pre-drilled holes on each Side KL , KR. 3. Use Allen Key 4 to tighten screws. Do not over-tighten. STEP 4 NOTE: The screwdriver is not included in the hardware pack. J 1. Use Phillips Screwdriver to attach Handle 9 to Drawer Front J . Repeat Step 1-4 for the second drawer.
ASSEMBLY Front / Avant Front / Avant Front / Avant Front / Avant STEP 5 1. Attach Small Divider D to Middle Frame E using 2 Allen Key Screws 1 . 2. Use Allen Key 4 to tighten screws. Do not over-tighten. Front / Avant Front / Avant Front / Avant Front / Avant STEP 6 1. Insert 2 Dowels 3 into pre-drilled holes on Large Divider C . 2. Use rubber mallet to tap Dowels 3 into bottom of holes securely. ½ length of Dowels should be exposed. 3.
ASSEMBLY Front / Avant Front / Avant Front / Avant Front / Avant Front / Avant STEP 7 1. Insert 2 Dowels 3 into pre-drilled holes on Large Divider C . 2. Use rubber mallet to tap Dowels 3 into bottom of holes securely. ½ length of Dowels should be exposed. 3. Attach Large Divider C to Bottom Shelf F using 3 Allen Key Screws 1 through predrilled holes. 4. Use Allen Key 4 to tighten screws. Do not over-tighten.
ASSEMBLY BR BL Front / Avant Front / Avant Front / Avant Front / Avant STEP 8 1. Insert 4 Dowels 3 into pre-drilled holes on each Side BL , BR . 2. Use rubber mallet to tap Dowels 3 into bottom of holes securely. ½ length of Dowels should be exposed. 3. Attach 3 Cam Lock Pins 2 to each Side BL , BR into guide holes. 4. Align and insert Cam Lock Pins on Sides BL , BR into pre-drilled holes on Bottom Shelf F . 5. Place 6 Cam Locks 2 into pre-drilled holes on Bottom Shelf F 6.
ASSEMBLY BR Front / Avant Front / Avant Front / Avant Front / Avant BL Front / Avant STEP 9 1. Insert 2 Dowels 3 into top corners of each Side BL , BR . 2. Use rubber mallet to tap Dowels 3 into bottom of holes securely. ½ length of Dowels should be exposed. 3. Align pre-drilled holes bottom corners of Top A with Dowels 3 in Sides BL , BR . 4. Attach Top A to Sides B and Small Divider D using 9 Allen Key Screws 1 . 5. Use Allen Key 4 to tighten screws. Do not over-tighten.
ASSEMBLY STEP 11 NOTE: The screwdriver is not included in the hardware pack. Fro nt / Ava nt BR H Fro nt / Ava nt BL Fro nt / Ava nt Fro nt / Ava nt H 1. Attach Hings on Doors H to Sides BL , BR using Phillips Screws 7 into pre-drilled guide holes. 2. Attach Magnet Plates 10 to bottom corner of Doors H using Phillips Screws 8 . into guide holes on Doors H . 3. Attach Magnets 10 to Bottom Shelf F using Phillips Screws 8 into guide holes on Bottom Shelf F . 4.
ASSEMBLY STEP 12 HR BR BL HL BL 1. Use 4 Shelf Supports 6 for each Shelf Cabinet G in desired location. 2. 2 Shelf Supports 6 may be used on back top of each Shelf Cabinets G as a tipping restraint. 3. Insert assembled drawers into drawer glides on assembled cabinet.
FURNITURE TIP OVER RESTRAINT ASSEMBLY WARNING Serious or fatal crushing injuries can occur from furniture tip-over. If the furniture tip over restraint kit is not in the box, please contact our customer service department in order to obtain another kit before using the furniture. STEP 13 NOTE: The screwdriver is not included in the hardware pack.
FURNITURE TIP OVER RESTRAINT ASSEMBLY Furniture Tip Over Restraint Instructions: 1. Attach one of the mounting brackets securely to the back edge of the furniture. Use the shorter screw. 2. Determine where furniture is to be placed and mark location on the wall for mounting bracket screw hole approximately 2 inches below the bracket mounted to the furniture. x 3. 4. 5. 6. 7. Drill a 3/16 inch hole in the wall.
WARRANTY Thank you for purchasing our product. These products have been made to demanding, high-quality standards and are guaranteed for domestic use against manufacturing faults for a period of 12 months from the date of purchase. This warranty does not affect your statutory rights. In case of any malfunction of your product (failure, missing parts, etc.) please contact us at our toll free. We reserve the right to repair or replace the defective product, at its discretion.
