ENTRYWAY STORAGE BENCH 1/15
Questions, problems, assembly help, missing parts? No need to return the product, we will gladly help and ship your replacement parts free of charge Please call Customer Service In order to assist you in a timely manner, please have the following information ready: Model # _______________________ Part Number or Letter_______________________ Purchased at ___________________Date of Purchase ___________________________ If you wish to return the product, please contact the retailer where the product was purch
IMPORTANT : Please read this manual carefully before beginning assembly of this product. Keep this manual for future reference. SAFETY INFORMATION Identify all the parts and hardware. Do not discard of the packaging until you have checked that you have all of the parts and hardware required. Hardware package may have spare parts. WARNING: This item contains small parts which can be swallowed by children and pets. Keep children and pets away during assembly.
IMPORTANT : Please read this manual carefully before beginning assembly of this product. Keep this manual for future reference. CARE and MAINTENANCE Perhaps the greatest environmental damage to wood furniture comes from wide swings in relative humidity (RH) in our homes. Wood absorbs and desorbs water as relative humidity rises and falls, and in doing so it swells and shrinks. Making matters worse, it expands and contracts unequally along different grain directions.
PRE-ASSEMBLY INFORMATION PARTS DESCRIPTION AL AR LEFT SIDE QTY 1 SEAT QTY 1 RIGHT SIDE QTY 1 D E Up Side / Vertical C B DIVIDER QTY 1 F FRONT QTY 1 G BACK QTY 1 BACKREST QTY 1 H BOTTOM PANEL QTY 1 BOTTOM SUPPORT LEG QTY 1 NEED HELP? For help with assembly or if you are missing a part, please call customer service 5/15
PRE-ASSEMBLY INFORMATION HARDWARE DESCRIPTION 1 2 ALLEN KEY BOLT M6 X 40 mm QTY 8 4 3 ALLEN KEY BOLT M6 X 30 mm QTY 4 5 LID SUPPORT QTY 1 7 6 WOOD DOWEL 8 X 30 mm QTY 1O ALLEN KEY QTY 1 8 PHILLIPS SCREW M3 X 12 mm QTY 9 ALLEN KEY SCREW M6 x 30 mm QTY 2 9 PHILLIPS SCREW M4 X 25 mm QTY 6 PHILLIPS SCREW ROUND HEAD M4 X 15 mm QTY 4 Required Phillips screwdriver Rubber mallet Not Included NEED HELP? For help with assembly or if you are missing a part, please call customer service 6/15
COMPONENTS – KEY DIAGRAM B Up Side / Vertical AR C F AL Up Side / Vertical G 7/15
ASSEMBLY STEP 1 3 Hinge l / Vertica Up Side 6 Small pre-drilled holes 1. Insert Dowel 6 into Divider C . 2. Use rubber mallet to tap Dowel 6 into bottom of holes securely. 1/2 length of Dowels should be exposed. 3. Align pre-drilled holes on bottom of Back F with Dowel 6 on Divider C . ( Note: please pay close attention to the location of the 2 small guide holes which accommodate the lid support. They need to be on the same side as the hinges ). 4.
ASSEMBLY STEP 2 G G C Up Sid e / Vert ical C Up Side / Vertical F 1. Attach Bottom Panel G to Divider C & Back F by sliding on the gap between Divider C & the long rail on Back F .
ASSEMBLY STEP 3 NOTE: The screwdriver is not included in the hardware pack. D 8 8 C Up Sid e 6 / Vert ical 1. Insert Dowel 6 into Divider C . 2. Use rubber mallet to tap Dowel 6 into bottom of holes securely. 1/2 length of Dowels should be exposed. 3. Align pre-drilled holes on bottom of Front D with Dowel 6 on Divider C . 4. Using 2 Phillips Screws 8 to attach Divider C to the middle bar on Front D .
ASSEMBLY STEP 4 AL D C G F D F G AR 1. Insert 4 Dowels 6 into each Side AL & AR at specified location. 2. Use rubber mallet to tap Dowels 6 into bottom of holes securely. 1/2 length of Dowels should be exposed. 3. Align pre-drilled holes on side bars of Front D & Back F with Dowel 6 on each Side AL & AR . 4. Using 4 Allen Key Bolts 1 (40mm length ) to attach Front D & Back F to each Side AL & AR .
ASSEMBLY STEP 5 NOTE: The screwdriver is not included in the hardware pack. H 8 G H 1. Attach Bottom Support Leg H into pre-drilled holes of Bottom Panel G using 4 Phillips Screws 8 . 2. Use Phillips screwdriver to tighten Screws. Do not over-tighten.
ASSEMBLY STEP 6 NOTE: The screwdriver is not included in the hardware pack. 7 B 1. Attach Seat B to 3 Hinges on Back F using Phillips Screws 7 ( using guide holes underneath of Seat ). 2. Use phillips screwdriver to tighten Screws. Do not over-tighten. STEP 7 B C 4 9 1. Attach Lid Support 4 into pre-drilled holes of Seat B and Divider C using Phillips Screws Round Head 9 . 2. Use phillips screwdriver to tighten Screws. Do not over-tighten.
ASSEMBLY STEP 8 AL AR E 2 5 1. Attach Backrest E to back of Sides AL & AR using Allen Key Bolts 2 into pre-drilled holes. 2. Use Allen Key 5 to tighten Bolts. Do not over-tighten.
WARRANTY Thank you for purchasing our product. These products have been made to demanding, high-quality standards and are guaranteed for domestic use against manufacturing faults for a period of 12 months from the date of purchase. This warranty does not affect your statutory rights. In case of any malfunction of your product (failure, missing parts, etc.) please contact us at our toll free service line or by email We reserve the right to repair or replace the defective product, at its discretion.