Installation Instructions

INSTALLATION INSTRUCTIONS
WARNING! SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER.
PREPARING FOR INSTALLATION (Fig. 1)
1. Shut off power at the circuit breaker (avertissement! couper le
courant au niveau des fusibles ou du disjoncteur) and remove
the old fixture including the mounting hardware.
2. Carefully unpack your new fixture and lay out all the parts in a
clear area. Take care not to misplace any small parts
necessary for installation.
4. Attach the canopy loop (I) to the nipple (G). Note: The
length of the nipple (G) into the cross bar (E) may be
adjusted if necessary.
5. Adjust the chain (K) to the desired length by removing the
links if needed and attach one end of the chain to the fixture
loop (L). Pass lock collar (J) followed by canopy (H) over the
chain and allow them to rest carefully on the cover (N) and
then attach the other side of the chain to canopy loop (I).
6. Carefully pass the fixture wires and bare ground wire through
the chain (K), canopy loop (I) and nipple (G).
CONNECTION THE WIRES (Fig. 2)
7. Connect the electrical wires as shown in Fig.2. making sure
that all wire connectors(B)are secured. If your outlet box has
a ground wire (green or bare copper), connect the fixture’s
ground wire to it. Otherwise, connect the fixture’s ground wire
directly to the cross bar using the green screw provided.
FINISHING THE INSTALLATION (Fig.1)
8. Align canopy (H) to nipple (G) and secure with lock collar (J).
9. Unscrew the screw (M), separate the cover (N) from
the fixture frame(S)
10. Place the glass(P) into the slot of the fixture frame(S) and
then secure it with the glass clip(R), then attach the fixture
frame(S) to the cover(N) with the screws(M).
11. Bulb information: (1 x AC LED 13W included.)
DO NOT EXCEED THE MAXIMUM WATTAGE RATING!
(NE PAS DEPASSER LA PUISSANCE NOMINALE
MAXIMALE!)
Replacing LED module (Fig. 3)
The LED module can be replaced by a qualified electrician and shut off the
power at the circuit breaker and remove fixture from the outlet box without
cutting of wire and without damage to any decorative element to which the
fixture is attached. See installation steps for more details (Fig 3.)
a. Remove the aluminum sheet (X) by loosening screws (Y). Carefully
disconnect the wire covers (Q).
b. Remove the module cover (R), loosen the screw (Z) to disassemble the
module (W), washer (V), aluminum sheet (X), gasket (U), nut (T).
c. Carefully remove the LED module (W) for re-lamping. Note: The LED
module should be provided by a specified supplier.
d. For better heat dissipation the LED module (M) should be installed with
the heat transfer silicone when re-lamping
Your installation is now complete. Return power to the outlet box and
test the fixture.
Fig. 1
FIXTURE
WIRES
SMOOTH
FIG.2
HOUSE
WIRES
BLACK
(HOT)
FIXTURE
WIRES
RIBBED
HOUSE
WIRES
WHITE
(NEUTRAL)
FIXTURE
WIRES
GREEN OR
BARE
COPPER
(GROUND)
HOUSE
WIRES
GREEN OR
BARE COPPER(GROUND)
Notice:It is important to use proper chain pliers(not included)
To OPEN and CLOSE the chain included with this fixture.Do
not open them with other tools that may twist or stress the
chain links. It is important to use proper chain pliers like the
ones shown in the diagram.
IMPORTANT: FIXTURE SHOULD BE INSTALLED BY A
QUALIFIED ELECTRICIAN TO ENSURE PROPER
WIRING AND INSTALLATION.
Fig.3
READ AND SAVE THESE INSTRUCTIONS
Cross bar
Mounting screw (2)
Grounding screw(1)
Nipple and nut (1)
AVERTISSEMENT! COUPER LE COURANT AU NIVEAU DES FUSIBLES OU DU DISJONCTEUR.
Chain
3. Attach the cross bar (E) to the outlet box (A) with the outlet
box screws (F) (size:8-32*1/2L). Install nipple (G) into
crossbar (E) and secure with the hex nut(C) and the washer
(D) provided. Note: the side of mounting plate marked “GND”
must face out.