Installation & Assembly

IMPORTANT:
• ALL INSTALLATION WORK SHOULD BE DONE BY ACCREDITED PROFESSIONAL.
• SHUT OFF POWER SUPPLY AT FUSE OR CIRCUIT BREAKER!
• USE ONLY THE SPECIFIED BULBS. DO NOT EXCEED THE MAXIMUM WATTAGE!
PREPARING FOR INSTALLATION
Remove all of the contents from the carton. See the important notes
above. Shut off the power at the circuit breaker and completely remove
theoldxturefromtheceiling,includingtheoldmountingstrap.
Fromthepartsbagremovethemountingstrapassembly.Oneendof
nipple(F)shouldbeattachedtomountingstrap(A)withhexnutand
washer(C,D)inplace.Theotherendshouldhavecanopyloop(H)
attached.Attachmountingstrap(A)tothejunctionboxusingmounting
screws(B)andascrewdriver.Tightensecurely.Unscrewcanopyloop
collar (I) from canopy loop (H). Pass canopy (G) over the mounted
canopylooptotesttheheight.Approximatelyhalfofthecanopy
loop’sexteriorthreadsshouldbeexposed,andthecanopyloopcollar
shouldtsnuglyontothecanopyloop.Removecanopy(G)andadjust
theheightofnipple(F)andcanopyloop(H)untilthedesiredheightis
reached.
ASSEMBLING THE FIXTURE
Bymeasuring,determinethecorrectnumberofchainlinksneededfor
properhangingheight.Ifnecessary,useapairofplierstoopenand
removeanyexcesschain(J).Attachonechainconnector(K)toeach
endofchain(J).Twisttosecureinplace.Useoneofchainconnectors
(K)toattachchain(J)totoploop(L)andclosethechainconnector.
Attachoneendofeachdecorativechains(N)tohooks(M)onthecage
andonthetopcap.Feedthexturewiresupthroughonesideofthe
decorativechain(everythreelinksorso),pullingthewiresuntiltaut.
Feedthewiresthroughtoploop(L)andupthroughchain(J).Slide
canopy loop collar (H) and canopy (G) onto the chain/wire. Use the free
chainconnector(K)toattachchain(J)tocanopyloop(H).
CONNECTING THE WIRES
Haveanassistantsupportthexture’sweightwhilecompletingthe
wiring.Cutawaytheexcesswires.Threadthexture’swiresthrough
canopyloop(H)andnipple(G).Attachthexture’swirestothepower
supplywiresfromthejunctionbox.Connectblacktoblack(orsmooth);
whitetowhite(orribbed);groundtoground(greenorcopper).Twist
theendsofthewirepairstogether,thentwistonawireconnector.
Makesurealltwistsareinthesamedirection.Ifthereisnogroundwire
(greenorcopper)fromthejunctionbox,locategroundscrew(F)on
mountingstrap(A)andwrapthexture’sgroundwirearoundthegreen
groundscrew(F).Useascrewdrivertosecuregroundscrew(F)onto
themountingbracket.Tuckallwiresneatlyintothejunctionbox.
FINISHING THE INSTALLATION
Pushcanopy(G)uptotheceilingandslidecanopyloopcollar(I)up
beneaththecanopy.Tightlythreadcanopyloopcollar(I)ontocanopy
loop (H) to secure canopy (G) in place.
Your installation is now complete. Turn on the power and test the
xture.
CLEANING TIPS
Treat the xture gently! Regular cleaning will reduce the need for deep cleaning. For regular cleaning, turn off the light and wipe down the
xture with a clean lint-free cotton or microber cloth. Never spray cleaner directly onto the xture.
For Customer Service, contact
the place of purchase to arrange
for replacement parts.
BLACK
(Hot)
WHITE
(Neutral)
GREEN
(Ground)
HOUSE WIRES
SMOOTH
(Or Black)
FIXTURE WIRES
RIBBED
(Or White)
BARE COPPER
(Or Green)
H
I
G
J
K
O
N
L
Q
P
M
A
B
C
E
D
F
Assembly Instructions