Assembly Instruction

ManualsBrandsThree Posts ManualsCandle-Style ChandeliersSarah 5-Light Candle Style Classic / Traditional Chandelier

Warnings and Cautions

Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.

These instructions are provided for your safety. It is very important you read them completely before installing

the fixture. We strongly recommend that a licensed, professional electrician perform the installation.

Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool

before removal. Do not subject glass parts to any shock while in operation or shattering may result.

1of6

(5) Candelabra Base 60W Maximum

20-30 minutes

Identify and inspect all parts before beginning installation. Check package content list and diagrams

below to be sure all parts are present. If any parts are missing or damaged, do not attempt to assemble, install, or

operate the fixture. Contact customer service for replacement parts.

Light Source:

Estimated Assembly Time:

Preparation:

Tools Required: Flathead screwdriver, Phillips screwdriver, pliers, wire cutters, wire strippers, electrical tape,

safety glasses.

, .

. .

Part

Description

Quantity

A Crossbar

Nipple

1 pc.

2 pcs.

1 pc.

Hex Nut

Package Contents

Canopy Chain Loop

Lock Washer

1 pc.

Canopy Lock Ring

1 pc.

Fixture Chain

Ceiling Canopy

Fixture Loop Assembly

Fixture Body

1 pc.

Assembly Instruction Sheet

selection.

Please go to our website for product cleaning tips. Go to the

Care + Maintenance

Thank you for purchasing this product.

Need assistance with parts or assembly? Call our customer service or visit our website

Summary of content (6 pages)

PAGE 1
, . Assembly Instruction Sheet . . Please go to our website for product cleaning tips. Go to the Care + Maintenance selection. Tools Required: Flathead screwdriver, Phillips screwdriver, pliers, wire cutters, wire strippers, electrical tape, safety glasses. Light Source: (5) Candelabra Base 60W Maximum Estimated Assembly Time: 20-30 minutes Preparation: Identify and inspect all parts before beginning installation. Check package content list and diagrams below to be sure all parts are present.
PAGE 2
FINISH: TUSCAN BROWN 2.4 m m 13 G a GND 5.5” Dia. 1" 1 Overall Height 63” (Includes 48” Chain) 14” 24” Dia. (5) 60W Candelabra Base Bulbs (No Supplied) NO. 1 NOTE: ALL DIMENSIONS ARE ROUNDED UP TO THE NEAREST 1/2" REPLACEMENT PART DESCRIPTION CHAIN TUSCAN BROWN 4' 3.8MM 2of6 REQ.
PAGE 3
Assembly Instruction Sheet STEP 1 - Adjust Fixture Assembly Figure 1 A. Unfold support arms on fixture assembly to proper locations. STEP 2 - Attach Fixture Loop Assembly to Fixture Body Figure 2 Fixture Loop Assembly A. Thread Fixture Loop Assembly (J) to Fixture Body (I). Tighten until snug. Fixture Body STEP 3 - Attach Crossbar to Outlet Box Outlet Box A. Secure the Crossbar (A) to the outlet box with outlet box screws (not supplied). Tighten until snug.
PAGE 4
Assembly Instruction Sheet STEP 4 - Attach Nipple to Crossbar A. Thread one Hex Nut (D) onto the top end of the Nipple (B). B. Place one Lock Washer (C) over the top end of the Nipple (B) and then thread the Nipple (B) into the center lock hole of the Crossbar (A). C. Using pliers, thread the hex Nut (D) against the Crossbar (A) and hand tighten until snug. Crossbar Lock Washer Hex Nut Nipple Figure 4 STEP 5 - Attach Canopy Chain Loop to Nipple A.
PAGE 5
Assembly Instruction Sheet STEP 7 - Attach Fixture Chain to Canopy Chain Loop and Fixture Loop A. Adjust the Fixture Chain (H) to your desired length by removing the links if needed. You may need to use plier to open the chain links. If so, put a cloth over the chain to protect the finish from the pliers. B. Attach one end of the Fixture Chain (H) onto the Canopy Chain Loop (F) and then attach the other end of the Fixture Chain (H) onto the Fixture Loop on the top of the Fixture Loop Assembly (J).
PAGE 6
Assembly Instruction Sheet STEP 9 - Make Wire Connections A. Un-thread the Canopy Lock Ring (G) and slide Canopy Lock Ring (G) and Ceiling Canopy (E) down the Fixture Chain (H). B. Push all slack fixture wire through Canopy Chain Loop (F) into Outlet Box. Trim excess fixture wire leaving a minimum of 6 inch. Hanging out of the Outlet Box. C. Use standard wire connectors to make all wire connections. (Connectors are not included with fixture.