WARNING CHOKING HAZARD - Small Parts Not for children under 3 years. Adult assembly required. Night Stand NOTE: THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION. PLEASE READ AND KEEP FOR FUTURE REFERENCE.
Table of Contents Part Identification Hardware Identification Assembly Steps Assembly Tools Required 3 4 No.
Part Identification å While not all parts are labeled, some of the parts will have a label or an inked letter on the edge to help distinguish similar parts from each other. Use this part identification to help identify similar parts.
Hardware Identification å Screws are shown actual size. You may receive extra hardware with your unit.
Step 1 å Assemble your unit on a carpeted floor or on the empty carton to avoid scratching your unit or the floor. å Push twenty-four HIDDEN CAMS (1F) into the ENDS (A2), BACK (D), LONG FRONT/BACK SKIRTS (I), and SHORT SIDE SKIRTS (J). Arrow A2 1F A2 D I I Arrow 1F (24 used) J J Arrow Hole The arrow in the HIDDEN CAM must point toward the hole in the edge of the board.
Step 2 å Turn twenty-four CAM SCREWS (8F) into the TOP (B) and LEGS (E, F, G, and H). å Fasten four METAL BRACKETS (4G) to the SKIRTS (I and J). Use four BLACK 9/16" LARGE HEAD SCREWS (1S). 8F G H E F B 8F (24 used) The BRACKET should be even with the edge.
Step 3 Fasten the LEGS (E, F, G, and H) to the ENDS (A2) and SHORT SIDE SKIRTS (J). Tighten twelve HIDDEN CAMS. 1 2 These surfaces must be even. E S HI urfa DD ce EN wi CA th M S å A2 Metal bracket These surfaces must be even.
Step 4 VIEW THE DRAWER GLIDE VIDEO å Fasten the UNIVERSAL CABINET RAILS* (35AA) to the ENDS (A2). Use four GOLD 5/16" FLAT HEAD SCREWS (3S) through holes #1 and #3. å å NOTE: Use the holes shown.
Step 5 å Fasten the BACK (D) and LONG BACK SKIRT (I) to the LEFT REAR LEG (H). Tighten three HIDDEN CAMS. å Fasten the LONG FRONT SKIRT (I) to the LEFT FRONT LEG (F). Tighten one HIDDEN CAM.
Step 6 å Fasten the BACK (D) and LONG BACK SKIRT (I) to the RIGHT REAR LEG (G). Tighten three HIDDEN CAMS. å Fasten the LONG FRONT SKIRT (I) to the RIGHT FRONT LEG (E). Tighten one HIDDEN CAM. å Fasten the BOTTOM (C) to the SKIRTS (I and J). Use four BLACK 9/16" LARGE HEAD SCREWS (1S) through the METAL BRACKETS and into the BOTTOM. å Push a CAM COVER (13P) onto each HIDDEN CAM on the SKIRTS (I and J).
Step 7 å å Carefully stand your unit upright. Fasten the TOP (B) to the ENDS (A2). Tighten four HIDDEN CAMS.
Step 8 VIEW THE T-SLOT BOX DRAWER VIDEO å Fasten the DRAWER SIDES (D42 and D43) to the DRAWER BACK (D154). Use four BLACK 1-9/16" FLAT HEAD SCREWS (30S). å Slide the DRAWER BOTTOM (D960) into the grooves in the DRAWER SIDES and DRAWER BACK. 30S BLACK 1-9/16" FLAT HEAD SCREW (4 used in this step) D43 D154 D42 Groove Be sure the DRAWER BOTTOM inserts into the DRAWER BACK groove. D43 D154 D960 D42 With the palm of your hand, tap the DRAWER BOTTOM into the grooves.
Step 9 VIEW THE T-SLOT BOX DRAWER VIDEO å Pull the DRAWER FRONT BRACKETS (7G) apart and slide them into the grooves in the DRAWER SIDES (D42 and D43). You may need to gently tap them in with a hammer. å NOTE: The DRAWER FRONT BRACKETS are marked "RH" and "LH" for easy identification. å Fasten the DRAWER FRONT (K) to the DRAWER FRONT BRACKETS (7G). Use two BLACK 9/16" LARGE HEAD SCREWS (1S).
Step 10 VIEW THE DRAWER GLIDE VIDEO å Fasten the DRAWER RIGHT (35AC) to the DRAWER RIGHT SIDE (D42) and the DRAWER LEFT (35AD) to the DRAWER LEFT SIDE (D43). Use four GOLD 5/16" FLAT HEAD SCREWS (3S) through holes #1 and #2. å å NOTE: The glides are not intended to rotate. Fasten the PULL (98K) to the DRAWER FRONT (K). Use two WASHERS (10I) and two SILVER 1/4" MACHINE SCREWS (61S).
Step 11 å To insert the drawer into your unit, tip the front of the drawer down and drop the glides on the drawer behind the glides on the unit. Lift the front of the drawer up and slide it into the unit å To make adjustments to the drawers, loosen the SCREWS in the DRAWER FRONT BRACKETS, make needed adjustments, and tighten the SCREWS. å å NOTE: Please read the back pages of the instruction booklet for important safety information. This completes assembly.
Chevet Utilisez les instructions d’assemblage en français avec les schémas étape par étape du manuel d’instruction en anglais. Chaque étape en français correspond à la même étape en anglais. La pièce devant être attachée à l’élément est représentée en gris sur les schémas de chaque étape pour plus de précision. Comparer la “Liste de pièces” ci-dessous avec la “PART IDENTIFICATION” du manuel en anglais pour vous familiariser avec les pièces avant l’assemblage.
ÉTAPE 1 ÉTAPE 4 Assembler l'élément sur un sol à moquette ou sur le carton vide pour éviter d'endommager l'élément ou le sol. Fixer les GLISSIÈRES D'ÉLÉMENT UNIVERSELLES* (35AA) aux EXTRÉMITÉS (A2). Utiliser quatre VIS TÊTE PLATE 8 mm DORÉES (3S) à travers les trous nº 1 et nº 3. Enfoncer vingt-quatre EXCENTRIQUES ESCAMOTABLES (1F) dans les EXTRÉMITÉS (A2), l’ARRIÈRE (D), les PLINTHES LONGUES AVANT/ARRIÈRE (I) et les PLINTHES LATÉRALES COURTES (J). REMARQUE : Utiliser les trous indiqués.
ÉTAPE 7 ÉTAPE 10 Relever, avec précaution, l'élément dans sa position verticale. Fixer un TIROIR DROIT (35AC) sur le CÔTÉ DROIT DE TIROIR (D42) et un TIROIR GAUCHE (35AD) sur le CÔTÉ GAUCHE DE TIROIR (D43). Utiliser quatre VIS TÊTE PLATE 8 mm DORÉES (3S) à travers les trous nº 1 et nº 2. Fixer le DESSUS (B) aux EXTRÉMITÉS (A2). Serrer quatre EXCENTRIQUES ESCAMOTABLES. ÉTAPE 8 Fixer les CÔTÉS DE TIROIR (D42 et D43) à l'ARRIÈRE DE TIROIR (D154). Utiliser quatre VIS TÊTE PLATE 40 mm NOIRES (30S).
Mesa de noche Use estas instrucciones de ensamblaje en español junto con las figuras paso-a-paso provistas en el folleto inglés. Cada paso en español corresponde al mismo paso en inglés. Se destacan las figuras de cada paso con una tonalidad oscura para mostrar precisamente cual parte se debe montar a la unidad. Compare la “Lista de Part” abajo con la “Part Identification” en el folleto en inglés para familiarizarse con Las partes de ensamblaje.
PASO 1 PASO 4 Ensamble la unidad sobre un piso alfombrado o sobre el cartón vacío para evitar rayar la unidad o el piso. Fije los RIELES UNIVERSALES DE GABINETE* (35AA) a los EXTREMOS (A2). Utilice cuatro TORNILLOS DORADOS DE CABEZA PERDIDA de 8 mm (3S) a través de los agujeros No. 1 y No. 3. Empuje veinticuatro EXCÉNTRICOS ESCONDIDOS (1F) en los EXTREMOS (A2), el DORSO (D), FALDONES LARGOS DELANTEROS / POSTERIORES (I) y FALDONES LATERALES CORTOS (J). PASO 2 NOTA: Utilice los agujeros indicados.
PASO 7 PASO 10 Cuidadosamente ponga la unidad en posición vertical. Fije el PANEL SUPERIOR (B) a los EXTREMOS (A2). Apriete cuatro EXCÉNTRICOS ESCONDIDOS. Fije un CAJÓN DERECHO (35AC) al LADO DERECHO DE CAJÓN (D42) y un CAJÓN IZQUIERDO (35AD) al LADO IZQUIERDO DE CAJÓN (D43). Utilice cuatro TORNILLOS DORADOS DE CABEZA PERDIDA de 8 mm (3S) a través de los agujeros No. 1 y No. 2. PASO 8 NOTA: Los corrimientos no están concebidos para rotar. Fije los LADOS DE CAJÓN (D42 y D43) al DORSO DE CAJÓN (D154).
WARNING Please use your furniture correctly and safely. Improper use can cause safety hazards, or damage to your furniture or household items. Carefully read the following chart. Look out for: What can happen: How to avoid the problem: • Overloaded drawers and shelves. • Risk of injury. • Never exceed the weight limits shown in • Top-heavy furniture can tip over. the instructions. • Overloaded drawers or shelves can break. • Work from bottom to top when loading shelves and drawers.
So, how did it go? Set a world record for speed? Feeling good about yourself? Nice. Get social with it on any of these quality share sites.
