TD201 BEDIENUNGSANLEITUNG USER GUIDE MANUEL D’UTILISATION РУКОВОДСТВО ПОЛЬЗОВАТЕЛЯ 使用手册 16 USER GUIDE
01 07 02 03 04 08 05 09 06 FEATURES / TOP PANEL 17
01. Counterweight The counterweight is used for precise adjustment of the stylus pressure on the vinyl, to properly balance the tonearm. 02. Anti-Skating Control To set the anti-skating force of the tonearm. 03. Tone arm Lever Use this lever to lower and raise the tonearm. 04. Tone arm Lock (arm rest) To lock the tone arm in place when not in use. 05. Headshell This holds the needle in place and provide needle protection 06.
10 11 12 13 14 10. Grounding terminal A direct electrical connection to the earth 11. RCA JACKS selector Plug in the RCA cable, and connect the cable to the audio amplifier 12. Pre Amp ON/OFF selector ON: Connect the RCA cable to the LINE-IN terminal of the amplifier. OFF: to stop the LINE-IN terminal of the amplifier.
13. Power Supply Jack To connect the power cable for power supply 14.
DUST COVER INSTALLATION 01. Unwrap the two hinges and the dustcover. 02. Note that the hinges have a clamp side and a tab side. 03. Note that the dustcover has two spots on its rear edge shaped to accept the clamps. 04. Carefully push the clamps onto the dustcover in these locations 05. Now snap the two clamps into the areas indicated at the back of the turntable to accept them. MOUNT AND ADJUST 01. Place the aluminum turntable platter over the center spindle.
10. The scale indicates the stylus pressure in grams. The pressure of the cartridge supplied with this turntable is 3.5g, turn the entire counterweight counter-clockwise to “3.5” and the anti-skating to “3.5“. If a different cartridge is used, adjust the stylus pressure and the antiskating indicated to the corresponding specifications. MAINS CONNECTION An external switching power adaptor is supplied with this turntable. There are the RCA jack on the rear panel of the turntable.
TO REPLACE THE STYLUS • Put the rest clip on the pick-up arm. • Remove the protective cap from the stylus. • Pull the stylus to the lower front and remove it. • Put in the new stylus following the reverse procedure. • Replace the protective cap on the stylus. TO REMOVE THE CARTRIDGE • Put the rest clip on the pick-up arm. • Remove the stylus to prevent damage. • Remove the two cartridge fixing screws. • Disconnect the four link wires at the back of the cartridge.
We would also point out that for the same reason your stylus should be replaced periodically (approximately every 250 hours). Dust the stylus from time to time using a very soft brush dipped in alcohol (brushing from back to front of the cartridge). WHEN TRANSPORTING YOUR RECORD PLAYER DO NOT FORGET TO: Replace the protective cap on the stylus.
Turntable section Drive System Belt Drive Motor DC Motor Speed 33 1/3 RPM, 45 RPM Rotation Speed Variation +/–2% Wow and Flutter 0.
Tonearm section Alumi tube Type Static Balance, Straight Effective Arm Length 8.8“, 223.6mm Stylus Pressure Range 0 to 4g Supported Cartridge Weight 3.5 bis 6.0g Overhang 18.
Cartridge section Type MM type (Audio-Technica AT3600) Stylus Construction Bonded Diamond Frequency Response 20Hz to 20kHz Channel Balance >18dB Kanalgleichheit 2.5dB Vertical Tracking Angle 20 degrees Supported Load Impedance 47k ohms Output Voltage 2.5mV (1kHz, 3.54cm/sec.) Stylus Pressure 3.5g +/–0.5g Cartridge Weight 5g +/–0.
Analog Output Connector RCA Pin jack (Gold-plated) Power AC 100 to 240V, 50/60Hz Power Consumption 1.5W (less than 0.5W at Standby) Overall Dimensions (W x D x H) 420 x 355x 121mm Weight Approx. 3.
