THS 812 Digitální satelitní přijímač pro vysoká rozlišení obrazu Návod k obsluze Používateľská príručka User manual Evolution. Emotion. Passion www.thomsonstb.
18 Nov 2013 18:46 Table of Contents 2 2 3 3 3 3 4 4 4 4 4 4 5 5 5 5 6 6 6 6 7 7 7 8 9 9 9 10 10 10 10 10 10 11 11 11 11 12 16 17 18 21 22 23 THOMSON declares that this item complies with the basic requirements and other relevant regulations of directives 2004/108/EC and 73/23/EC, RoHS 2002/95/EC. THOMSON is a trademark of TECHNICOLOR S.A. used under license to STRONG Europe. Subject to alterations.
Licenses ANY USE OF THIS PRODUCT IN ANY MANNER OTHER THAN PERSONAL USE THAT COMPLIES WITH THE MPEG-2 STANDARD FOR ENCODING VIDEO INFORMATION FOR PACKAGED MEDIA IS EXPRESSLY PROHIBITED WITHOUT A LICENSE UNDER APPLICABLE PATENTS IN THE MPEG-2 PATENT PORTFOLIO, WHICH LICENSE IS AVAILABLE FROM MPEG LA, LLC, 6312 S. Fiddlers Green Circle, Suite 400E, Greenwood Village, Colorado 80111 U.S.A.
Safety Precautions open the receiver cover. It is dangerous to touch the inside of the receiver due to high voltage currents and possible electrical hazards and your warranty will be void. Refer all maintenance or servicing to suitably qualified personnel. yy When you are connecting cables, be sure that the receiver is disconnected from the mains supply voltage. Wait a few seconds after switching off the receiver before you move the receiver or disconnect any equipment.
yy Please ensure that either the USB device is already formatted to FAT32. 2.0 Your Receiver 2.1 Default PIN-code Default PIN-code of receiver is “0000”. This one can be modified later on. 2.2 Master MR PIN-code This PIN is used for maturity rating and playback of protected records and is supplied by the operator. 2.3 Front Panel The front flap can be opened at the top for inserting the smart card 1. 2. 3. 4. 5. 6. 7.
English 10. OK Menu Off: Displays the current channel list. Menu On: Opens the highlighted setting 11. MENU Opens the main menu and from main menu you will get one step back 12. EXIT/SORTIE Exits from the menu, sub-menu or cancels actions 13. GUIDE Shows the EPG (Electronic Programme Guide) in TV mode 14. V+/VIncreases/decreases volume in all modes 15. ! Mutes audio output of the receiver in every mode 16. P+/PProgramme +/17. SUB Shows the list of subtitle languages if available 18.
1. Connect the LNB or Mono block for ASTRA 19.2 /ASTRA 23.5 of your satellite antenna to the SAT IN connector of your receiver using a good quality coaxial cable and suitable ‘F-connector’ plugs. 2. Connect one end of a good quality HDMI cable (V1.3 or higher) to the HDMI connector of your receiver and the other end to the HDMI input of your TV set. 3. Plug the power adapter jack to the receiver and the other end to a suitable wall outlet.
4.1 Language, Country and Video setup After turning on the power for the first time, the OSD language, Country and Video Setting menus will be shown. First choose your language with tu, then press pq to select your preferred country. As the last step on this screen use pq to select Video Setting. Select which connection you will use to your TV screen: SCART or HDMI cable. Please, read the displayed instructions for each screen carefully which will help you adjust the settings correct and easily.
When all settings have been made, press BLUE Next to continue. To check or change the settings for the satellite on port 1 press OK to enter the submenu. If port 1 is already correctly adjusted and you have proper signal quality and strength banners you can adjust the port 2 if you have a satellite connected there. Use pq to select it and proceed like below chapter describes. This you can do for up to 4 satellite positions. 4.3.
5.0 Quick guide to using your receiver We at THOMSON understand that you can’t wait to enjoy your new HD receiver. The following quick guide will make you familiar with the basic operation of this device. We do, however, advice you to read the full manual to get the best performance from your THOMSON HD receiver. To turn your receiver ON or to Standby, use the q button on the remote control or the button on the left side of the front panel. Choose a channel with pq or the P+/P- buttons.
6.1.3 Using the P+/P- keys P+ or p will switch to a higher channel. P- or q will switch a lower channel. 6.2 Info banner At any time during viewing mode you can press the button to get info about the current channel and programme*. For the current programme information use tu to change between the NOW and NEXT event info. Press twice to see technical details about the current channel.
By pressing the LIST button you can check the set timers and delete a timer by pressing the BLUE button. With YELLOW or EXIT/SORTIE you can close this menu again. If the highlight is on a channel, you can press OK to directly switch to this channel. Note: vailability of EPG data depends on broadcast and can be displayed for up to 7 days. If A you are opening the EPG just after the receiver was switched on or changed to another transponder, we recommend waiting for approx.
7.1 Installation This menu allows you to change satellite settings and to search for channels. Further you can adjust important settings for your receiver. It consists of the following sub-menus: Antenna Setup, Channel Search, System Settings, Parental Lock and Factory Reset. Choose a sub menu with pq and press OK to advance. 7.1.1 Antenna Setup Use this menu to change or add the settings for an already installed or new satellite and to configure its parameters.
Set Limit: Press OK to open this sub menu for setting up the maximum position of you dish. This is needed if your dish will touch a wall and can be damaged. GOTO X set-up In this menu you can set your geographical location if you use a motor and it supports GOTO X. Press OK to open the list of available satellites and chose the desired one with the tu buttons. Your longitude: Use the 0 ~ 9 buttons to enter the values of your longitude. Press OK to confirm the value.
Note: hen you want to add technical data for a new transponder we recommend verifying it W by consulting websites like: www.lyngsat.com or www.kingofsat.net or you can refer to professional journals. 7.1.3 System Settings Use the System Settings menu to configure settings for language, audio, video, look and feel of your receiver. Choose a setting with pq and press OK to list the possibilities or use tu to change the value of the highlighted setting.
Conversion: Letterbox, Pan&Scan or Combined, to choose the preferred picture format. Video Output: RGB or CVBS, depending on what your TV set supports, but for Scart we recommend RGB. Resolution: Only selectable for HDMI HDCP: ON or OFF, please see the note above. After all settings are adjusted following to your preference, choose Save with pq and press OK. The receiver returns to the menu.
setting you will have to enter your PIN code when switching through channels which support EPG or submit EPG based parental rate. Not rated content: Use tu buttons to select Blocked or Unblocked. In order to block or not block the channels with PIN code before decoding, where the EPG based parental rate not broadcasted. New PIN Code: Enter the PIN code of choice with the 0~9 buttons. Confirm PIN Code: Use the 0~9 buttons to confirm your new PIN code.
Note: lease connect a correctly formatted USB storage device with the correct software P file loaded to the root directory and then connect it to your receiver. After the receiver successfully has started the loading process (progress bar will be shown) please remove the USB device! Warning: EVER disconnect the receiver from the mains or switch the power OFF during the update N procedure.
a defined rate for a movie or special event you can use this setting to protect children from watching improper content for their age. These PIN codes are also used to start playback of a recording with protection. The availability and access of this menu depends on if the broadcaster supports/opens this function. Maturity Rating Master PIN: Use the 0~9 buttons to access this menu options. Enter the MATURITY Rating PIN. Maturity Rating action: Use tu to set ON or OFF.
favourite group and press RED to delete this channel. Then press t to change to the left side again if you want to add other channels to favourite groups. Note: emoving a channel from a favourite group doesn’t remove this channel from the channel R list. Move channels Press the YELLOW button to move a channel position in the channel list for the selected favourite group. Select the channel you want to move with pq, then press OK highlight the selected channel for moving.
7.4.5 HDD Manager (PVR) The HDD Manager menu allows you to select a recording file for Playback, Delete, Lock and Rename. It allows you to select another Partition and/or Format for the connected HDD into FAT32. Make sure you have connected your external HDD to the USB port on the rear panel on which you made recordings before. Playback Use pq to highlight a recorded file and OK to start playback.
SMS method. After you have entered a new name for the selected recording, press OK to store. Sort Press MENU and select Sort and the way you like to display the record list. Select between Sort by Date if you want to sort by date of events. Select Sort by Alphabet to sort on A ~ Z order. Press OK to confirm. Remove USB Press MENU and select Remove USB if you like to disconnect your external HDD or USB device safely from the receiver. Press OK to confirm. 7.
Duration: Use the 0~9 buttons to digit the duration of the timer. For duration of 45 min, just enter 45 and press OK or for 1h 30min, just enter 130 and press OK. Enable: Choose between Yes or No. You have to choose Yes if you want the timer to start at the desired time. By pressing the YELLOW Summary button you can check the set timers and by pressing the BLUE button you can delete a timer. With YELLOW or EXIT/SORTIE you can close this menu again.
The USB storage device is not working properly. The external USB HDD does not start. The receiver switches to Standby automatically. Message E4432 No Event Information. Enter PIN code. Cause The batteries of the remote control are not inserted, wrongly inserted or exhausted. Wrong formatted. Bigger sized HDD connected. USB 1.1 device connected. Power consumption is too high. Auto Standby function is activated and reached the adjusted time (default 3h).
Output voltage 12 V DC, 2.0A Power consumption: max. 20 W, typ. 8.00 W Power consumption in stand-by: max. 1.00 W Operating temperature: +0 to +40 °C Storage temperature: -10 to +70 °C Operating humidity range: 25 ~ 75% RH, non-condensing Size (W x D x H) in mm: 261 x 168 x 51 Weight: 0.
