MARS TECH LIMITED EXHIBIT A {PCC Ref. “Installation and Operating Instructions Furnished to the User” Thomson/26975 EXHIBIT A FCC ID: GOTH-6975 Mars tech Report No.
32-Channel Two-Line 900 MHz Caller ID with Call Waiting and Speakerphone Cordless Telephone User's Guide SH, AN We bring good things to life. FCC 1D: GOTH-6973 Mars tech Report No.
FCC REGISTRATION INFORMATION Your teleportation equipment iz registered with the Federal Communications Commission and is in compliance with parts 15 and 08, FCC Rules and Regulations. Notification to fhe Local Telephone Company Gn the Bio storm of this equipment is a dabs! indicating, among other infantryman, the FC Registration purer and Ringer Equivalence Surmise (FEN] for the equipment. You must, upon request, provides this information to your electioneer company.
INTRODUCTION Your Caller ID phone stares and displays specific information, provided by your local telephone company, to subscribers of Caller ID or similar caller identification services. You must subscribe to one of these services in order to use this unit. Your Caller ID phone enables you to: + Identify callers before you answer the phone. + View the time and date of each incoming call. + Record up to 40 Caller ID messages sequentially. « Know who called while you were away.
INSTALLATION AND SETUP Make sure your package includes the items shown here. power supply Wall mount bracket op Telephone line cord Base Modular JACK REQUIREMENTS You need an RJ14 type modular jack or two RJ11 type jacks. RJ11 is the most common type of phone jack, Either might look like the one pictured here. If you don’t have a modular jack, call your local phone company to find out how to get one installed.
INSTALLATION OPTIONS Although you can use your 2-line cordless telephone with a single phone line, you must have two lines (separate phone numbers} to use a two-line system. The following diagrams show two possible systems: Two Lines on Single Modular Jack One type of two-line phone system uses a single RJ14 modular jack which contains both phone lines. Connect the phone cord to the L1 + 1.2 jack. You must use a 4-conductor telephone line cord like the ones that are packed with your unit.
Desk Top INSTALLATION NOTE: For desktop charging only, the handset is able 16 charge facing up or down & Two Lines on a Single Modular Jack 1. Make sure wall mount bracket is securely fastened. 2. Set RINGER switch {on the handset) to ON, 3. Plug the power supply cord into the POWER 12V DC jack on the base and into an AC outlet. . Place handset in the base to charge for 12 hours, The CHARGE/NT fight {on the base) acmes on to indicate that the battery is charging.
Each Line on a Separate Modular Jack 1. Make sure wall mount bracket is securely fastened. 2. Set RINGER switch {on the handset] to ON. 3. Plug the power supply cord into the POWER 8V DC jack on the base and into an AC outlet, 4. Place handset in the base to charge for 12 hours, The CHARGE/NT light {on the base} comes on to indicate that the battery is charging. If you don't charge the handset battery properly {for 12 hours) when you first set up the phone, performance of the battery will be compromised.
‘WALL MOUNT INSTALLATION Two Lines on a Single Modular Jack Because it is necessary to charge the handset for 12 hours prior to connecting the phone for use the first time, it is better to leave the union a flat surface during initial charge before attempting to hang it on the wall. 1. Make sure the wall mount bracket is securely fastened. 2. Set RINGER switch to ON. 3. Place the handset in the base. 4. Connect the power supply cord into the base and the other end into an AC outlet.
Remove the wall mount bracket. Rotate it so that the bottom of the phone is flat. Reattach the wall mount bracket by inserting the tabs into the slots on the top of the unit first, and then snapping the bottom tabs into place. Plug the telephone line cord into the jack marked the back of the unit and plug the other end into a dual line modular wall jack. . Slip the mounting holes over the wall plate posts and side the unit down firmly into place. (Wall plate not included.
Each Line on a Separate Modular Jack Because i is necessary to charge the handset far 12 hours prior to connecting the phone for use the first time, iris better to leave the unit on a flat surface during initial charge before attempting to hang it on the wall, 1. Make sure the wall mount bracket is securely fastened. 2. Set RINGER switch to ON 3. Place the handset in the has. 4. Connect the power supply cord into the base and the other end into an AC outlet.
ot . Remove the wall mount bracket. Rotate it so that the bottom of the phone is flat. Reattach the wall mount bracket by inserting the tabs into the slots on the top of the unit first, and then snapping the bottom tabs into place. . Plug the telephone line cord into the jack marked the back of the unit. o ~ . Plug the telephone ling cord from the U1 + L2 jack into a single line modular jack that you want to be line 1. .
SETUP SETTING THE AREA CODE IMPORTANT: For proper Caller ID operation, you must enter your area code. 1. Make sure the phone is OFF, 2. Press the PROGRAM bunion on the base until ENTER AREA CODE shows on the display. , Enter your 3-digit area code using the number keys. 4, Press FORM/HOLD to confirm. w Tong /Pulse DIALING This adjustment allows you to select tone (touch-tone} or pulse {rotary} mode dialing. The phone is automatically set for touch-tone use.
Tone 1. Make sure the phone is OFF. 2. Press and release the PROGRAM button on the base until 7/7 SETTING shows on the display. 3. Press TONE®. TONE MODE shows on the display. 4. Press PERMUTE to confirm. Purse 1. Make sure the phone is OFF. 7. Press and release the PROGRAM button on the base until 7/7 SETTING shows on the display. 3. Press &, PULSE MODE shows on the display. 4. Press PERMUTE to confirm.
