Cut Sheet
WARRANTY: Thomas & Betts sells this product with the understanding that
the user will perform all necessary tests to determine the suitability of this
product for the user's intended application. Thomas & Betts warrants that this
product will be free from defects in materials and workmanship for a period of
two (2) years following the date of purchase. Upon prompt notication of any
warranted defect, Thomas & Betts will, at its option, repair or replace the
defective product or refund the purchase price. Proof of purchase is required.
Misuse or unauthorized modication of the product voids all warranties.
Limitations and Exclusions: THE ABOVE WARRANTY IS THE SOLE
WARRANTY CONCERNING THIS PRODUCT, AND IS IN LIEU OF ALL
OTHER WARRANTIES EXPRESS OR IMPLIED, INCLUDING BUT NOT
LIMITED TO ANY IMPLIED WARRANTY OF MERCHANTABILITY OR
FITNESS FOR A PARTICULAR PURPOSE, WHICH ARE SPECIFICALLY
DISCLAIMED. LIABILITY FOR BREACH OF THE ABOVE WARRANTY IS
LIMITED TO COST OF REPAIR OR REPLACEMENT OF THE PRODUCT,
AND UNDER NO CIRCUMSTANCES WILL THOMAS & BETTS BE LIABLE
FOR ANY INDIRECT, SPECIAL, INCIDENTAL OR CONSEQUENTIAL
DAMAGES.
Thomas & Betts Corp.
TIE 1
TIE 2
MDBOOT-0
MDBOOT-1
MDBOOT-2
MDBOOT-3
BLACK TY-RAP
®
CABLE TIE
STABILIZED NYLON
DOUBLE MALE
DISCONNECT
USE STANDARD
MD FEMALE DISCONNECT
1/4"
TIE 1
TIE 2
WARNING
RISK OF SHOCK, DISCONNECT
POWER BEFORE INSTALLATION.
WARNING
NOT FOR DISCONNECTING ENERGIZED CIRCUITS.
#16-14
#12-10
#8
#6
#12-10
#8
#6
#4
#2
#1
#2
#1
#1/0
#2/0
#3/0
#4/0
M2D1614M-0
M2D1210M-1
M2D8M-1
M2D6M-1
M2D1210M-2
M2D8M-2
M2D6M-2
M2D4M-2
M2D2M-2
M2D1M-2
M2D2M-3
M2D1M-3
M2D10M-3
M2D20M-3
M2D30M-3
M2D40M-3
MDBOOT-1
M2DBOOT-1
TY242M (2)
M2DBOOT-2
TY242M (2)
M2DBOOT-3
TY26M
MALE
WIRE SIZE
AWG
CATALOG NUMBERS
BOOT NO.
&
CABLE TIE
140B
DOUBLE MALE DISCONNECTS
INSTALLATION INSTRUCTIONS
NOTE: Some catalog numbers shown
above have sufxes: i.e. XXXXXG
(indicating special packaging). All crimp
settings for these parts are the same as
for the base numbers.
• Flame Retardant
Formulation
• Abrasion
Resistant
RATM600
• 90°C
Thomas & Betts Corporation
Memphis, Tennessee
www.tnb.com
© 2010 Thomas & Betts. All Rights Reserved.
TA00220 T Page 2 of 2
STEP 1
Select connectors as needed
for motor and line wire sizes.
Be sure to select connectors
within the suitable size
groups. Size groups may not
be inter-mated. Connectors
within each group may be
mated. (MD1210F-2 mated
with MD2M-2).
STEP 2
D
ress the wires to pigtail with
the motor leads.
STEP 3
C
rimp connectors with any
T&B installing tool as follows:
WT2000, WT1300, WT130A
Installs #16 through #10
*TBM20S installs #8 to #2
TBM5, TBM5S, TBM6,
TBM6S, TBM8, TBM8S,
TBM62BSCR, TBM25S, &
TBM6BSCR
*Requires (2) crimps
STEP 4
P
ush male pin into female
barrel until fully inserted.
STEP 5
S
lide insulator onto pigtailed
connectors until it stops.
STEP 6
Fasten
the rst tie at middle
of insulator, tightening snugly.
Fasten the second tie 1/4"
from end of boot as shown,
and tighten. Cut excess tie.
STEP 7
D
ress lead assemblies into
junction box.
INSTALLATION INSTRUCTIONS