Assembly Instructions THV 3.
Thomann GmbH Hans-Thomann-Straße 1 96138 Burgebrach Germany Telephone: +49 (0) 9546 9223-0 Internet: www.thomann.de 06.09.
Table of contents Table of contents 1 Safety instructions................................................................................................................. 5 2 Setup............................................................................................................................................. 6 2.1 Assembling the frame.................................................................................................... 6 2.2 Inserting the motor..................................
THV 3.
Safety instructions 1 Safety instructions DANGER! Danger for children Ensure that plastic bags, packaging, etc. are disposed of properly and are not within reach of babies and young children. Choking hazard! Ensure that children do not detach any small parts (e.g. knobs or the like) from the unit. They could swallow the pieces and choke! Never let children unattended use electrical devices. DANGER! Electric shock caused by short-circuit Do not modify the mains cable or the plug.
Setup 2 Setup 2.1 Assembling the frame Place the wide upper part (1) on the wide lower part with the long guide pin (2) and tighten the wing screws. ö $ Place the narrow upper part (3) on the narrow lower part with the short guide pin (4) and tighten the wing screws. # % ' ( Pull the cotter pin (5) out of the slot for the centre rod (6) of the wide and narrow base. & & # ' Insert the centre rod (6) into the slot of the wide base (2).
Setup 2.2 Inserting the motor Hang the drive belt (8) on the motor unit (9) as shown. The drive belt hangs loosely on the motor unit and is only tensioned when the resonators are installed. ) * Hook in the motor unit (9) with the drive belt on the control unit (10) of the narrow upper part (3) as shown. + * Connect the motor unit cable (11) to the control unit connector (12). $ , 2.3 Inserting bars and hanging in resonators ö .
Setup Hang the whole-tone resonator (15, closed tubes) between mounts ‘3’ and ‘4’ of the upper parts (1, 3) as shown. 0 Hang the semitone resonator (16, open tubes) between mounts ‘1’ and ‘2’ of the upper parts (1, 3) as shown. 1 1 0 Tighten the drive belt (8) around the motor drive shaft (17) and the two resonator drive shafts (18) as shown. ) 3 2 3 $ Place bar 1 (19) and bar 4 (20) into the mounts provided on the upper parts (1, 3).
Setup 2.4 Damper mounting 7 Loosen the thumbscrew from the damper beam (21) and remove the thumbscrew, knurled nut and felt washer. 7 6 Place the damper beam (21) with the spring on the mounting plate provided between bar 2 (13) and bar 3 (14). Align the connecting arms (22) so that they point towards the semitone resonator (16, open tubes). Reattach the felt washer, knurled nut, and thumbscrew to the damper beam (21) from below.
Setup Hook the pedal pull rod (23) into the mount on the pedal rod (7) as shown. ( 8 2.5 Installing sound plates Place the semitone sound plates (24) on bars 1 (19) and 2 (13). Thread the cord of the sound plates around the end pegs (26) and install each sound plate between the pegs of the bars. 9 Then place the whole-tone sound plates (25) on bars 3 (14) and 4 (20). Thread the cord of the sound plates around the end pegs (26) and install each sound plate between the pegs of the bars.
Protecting the environment 3 Protecting the environment Disposal of the packaging material For the transport and protective packaging, environmentally friendly materials have been chosen that can be supplied to normal recycling. Ensure that plastic bags, packaging, etc. are properly disposed of. Do not just dispose of these materials with your normal household waste, but make sure that they are collected for recycling. Please follow the notes and markings on the packaging.
Notes 12 THV 3.
Notes THV 3.
Notes 14 THV 3.
Musikhaus Thomann · Hans-Thomann-Straße 1 · 96138 Burgebrach · Germany · www.thomann.
