SignaTouch Control Installation Manual For Tutorials and Troubleshooting visit www.thermasol.
SignaTouch Control Installation Instructions 1 Important Information before You Install The SignaTouch Control must be installed inside the shower. The ThermaTouch control will only function on the current TFX, SSA and PRO Series generators. The control should be installed 60" from the floor of the shower and away from the steamhead. The steamhead should be installed 24" from the floor and 6" from any wall.
SignaTouch Control Installation Instructions 2 Tools and Materials Back of Control Power/Data M8 connection Controller Item STCX-XXX Silicone Mud Ring Item 04-8566 Installation instructions, warranty, static cling warning label Materials needed: o SignaTouch control o M8 cable o Silicone o Mud Ring o Other materials as required 3 Mud Ring Application Top Horizontal Installation Top Vertical Installation Shower wall Finished wall must be flush with the mud ring.
SignaTouch Control Installation Instructions 4 Control Installation and Data Cable Connection Installation with generator only Route the M8 cable through the finished wall to the back side of the control. (The other end of the cable runs to the steam generator location.) NOTE: It is recommended to run the cable through electrical conduit. DO NOT STAPLE the cable! Shower wall M8 Cable Installation with one of or all, SLSR, Digital shower valve, and steam generator.
SignaTouch Control Installation Instructions 5 Sealing Control THESE STEPS MUST BE TAKEN FOR CORRECT INSTALLATION OF THE CONTROL. REMOVE MUD RING FROM WALL CUTOUT BEFORE MAKING FINAL CABLE CONNECTIONS TO THE THERMATOUCH CONTROL. TEST THAT ALL CONNECTIONS ARE WORKING BEFORE SEALING THE CONTROL TO THE WALL. (Power on the control and see that it lights up). Coat the entire edge of the control with supplied waterproof silicone to fully seal the control to the wall.
SignaTouch Control Installation Instructions 6a Connecting SignaTouch to the Generator M8 Cable 6b Connecting SignaTouch to Serenity Light, Sound, Rainhead (if applicable) M12 Cable 110v M8 Cable Read warnings on page 2. For illustrative purposes only. Consult with qualified professional for steam room construction details. 6 THERMASOL.COM I 800.776.
SignaTouch Control Installation Instructions 6c Connecting SignaTouch to Digital Shower 110v M12 Cable M8 Cable 6d Connecting Total Wellness Package 110v M12 Cable M8 Cable M8 Cable Read warnings on page 2. For illustrative purposes only. Consult with qualified professional for steam room construction details. THERMASOL.COM I 800.776.
SignaTouch Control Installation Instructions 7 Steam Line and Steamhead Now you will need to decide on the steamhead placement in the shower so you can run the steam line from the generator to the steamhead. There are a couple of things you need to know about the placement of the steamhead and steam line itself. DO NOT install any valve in the steam line. Flow of steam must be unobstructed. The steam line can run up and then down, once; or horizontal; but never run down and then up.
SignaTouch Control Installation Instructions Steamhead Location DO NOT install the steamhead near the seating area or the user. DO NOT forget to install the steamhead rough-in fitting! C I nstall the steamhead 24" from the floor or bathtub rim and 6" from any corner. Steamhead is to be mounted as far as possible from typical bathing position (seated or standing) and installed as far from the in-shower controller as possible.
SignaTouch Control Installation Instructions D Once the shower wall is complete and the housing is sealed to the wall, remove the protective cap and insert the steamhead into housing. Use the supplied silicone to adherethe steamhead to the wall sealing out any water from getting behind the head. Use supplied o-ring lubricant to assist in steam head installation. A very small amount is all that is need directly on the o-rings.
SignaTouch Control Installation Instructions 9 Trouble Shooting, Tutorials and Error Codes Visit www.thermasol.com/solutions. Click on Troubleshoot then click on SignaTouch Control Error Codes. Read warnings on page 2. For illustrative purposes only. Consult with qualified professional for steam room construction details. 11 THERMASOL.COM I 800.776.
ThermaSol uses the following open source project: Qt5-GUI Framework-www.qt.io-LGPLv3 1958 STEAM WAY ROUND ROCK, TX 78665 PHONE: 800.776.0711 | FAX: 800.556.5257 | WWW.THERMASOL.
