MicroTouch Control +Steamhead Installation Manual For Tutorials and Troubleshooting visit www.thermasol.
MicroTouch Control Installation Manual For Tutorials and Troubleshooting visit www.thermasol.
MicroTouch Control Installation Instructions 1 Important Information before You Install The MicroTouch Control must be installed inside the shower. The MicroTouch control will only function on the current SSM, SSA and PRO Series generators. The control should be installed 60" from the floor of the shower and away from the steamhead. IMPORTANT: When locating and installing the MicroTouch, it is required to not place the control under any water-outlets, shower heads or in the direct path of flowing water.
MicroTouch Control Installation Instructions 2 Tools and Materials Controller (Contemporary style shown here) Materials needed: o MicroTouch control o CAN bus cable (included with generator o Silicone o Other materials as required Silicone Parts enclosed Mud Ring (RIK-TPMR-1) for MTMR-XX installation only Installation instructions, warranty, static cling warning label Tools needed: o 1/2” drill for surface mount o Follow pre-installation instruction on page 5 for recessed mount controls o Drill mo
MicroTouch Control Installation Instructions 4 Control Installation and Data Cable Connection Back of Control Route the data cable (included with generator) through the finished wall to the back side of the control. The other end of the cable runs to the steam generator location or if present to SWM-2 or PDM. NOTE: It is recommended to run the cable through electrical conduit. Connector Detail DO NOT pinch, nail, staple, wedge, or bind the data cable.
MicroTouch Control Installation Instructions 5 Mud Ring Installation + Sealing Control For Recessed Control Only (MTMR-XX and MTTR-NTS-XX) Silicone (included) Recessed Control (shown) Data Cable Step 1: BEFORE TILE - Use the supplied mud ring by attaching to wall face using a few standard screws. Then tile to the edge of the mud ring. Step 2: Once finished tile is completed remove mud ring from wall. Ensure that the total minimum depth is 5/8” so control face sits flush to wall.
MicroTouch Control Installation Instructions 6 Operation A Taking a Steam Bath On your ThermaSol MicroTouch Control, touch and release the power icon twice to power on. To turn off the steam unit touch and release the power icon once. Power on is verified when the control face shows lit LEDs and turns dark if power is off. C Start a Power Flush cleaning cycle To start a power flush manually, press and hold the + and – buttons for 5 seconds while the MicroTouch is in the on state.
MicroTouch Control Installation Instructions 7 Trouble Shooting, Tutorials and Error Codes Visit www.thermasol.com/solutions. Click on Troubleshoot then click on MicroTouch Control Error Codes Read warnings on page 3. For illustrative purposes only. Consult with qualified professional for steam room construction details. PN: 81193_NC 4/16 THERMASOL.COM I 800.776.
Steamhead Installation Installation Manual For Tutorials and Troubleshooting visit www.thermasol.
Steamhead Installation Instructions 2 Tools and Materials Steamhead (Contemporary style shown here) Silicone Parts enclosed Installation instructions Materials needed: o Steamhead o Steamhead Rough-In Housing 1/2" Copper Tubing (For PRO-650, PRO-850 3/4" drop elbow, 3/4" Copper Tubing 50' max.
Steamhead Installation Instructions 4 Steamhead Installation A A When finalizing installation, install the steamhead into the housing, making sure that the aromatherapy fill channels are facing upwards. B To ensure that no moisture gets behind the steamhead and into the wall, place a generous bead of waterproof silicone around the steamhead, using the machined groove (located on the back of the steamhead) as a guide.
1958 STEAM WAY ROUND ROCK, TX 78665 PHONE: 800.776.0711 | SUPPORT@THERMASOL .COM | WWW.THERMASOL .COM WWW.THERMASOL .
