User Manual VB5000SNA C 2005 Thermaltake Technology Co.,Ltd. All Rights Reserved. www.thermaltake.
Contents Chapter1 Product Introduction 1.1 Specification 1 Chapter2 Case Mechanical Operation 2.1 How to open the side panel 2.2 Installing 5.25" Device 2.3 Installing 3.5" HDD 2 3 4 2.4 Installing 3.5" Device to Drive Tray With Power Button 2.5 How to Remove the Fan & Fan Holder 2.6 BTX Upgraded Kits 2.7 PCI slot tool-free function operation 5 7 8 9 Chapter3 Motherboard & Leads Installation 3.1 Motherboard Installation 3.2 Case LED connections 3.3 USB2.0 & IEEE1394 Firewire connection 3.
Chapter1 Product Introduction 1.1 Specification Chapter2 Case Mechanical Operation 2.1 How to open the side panel VB5000SNA Remove two screws on the right side of the side panel displayed in the picture. Model Tai-Chi --- VB5000SNA Case Type Super Tower Net Weight 17.1 Kg Dimension 600 x 263 x 546 mm (H*W*D) Cooling System Front (intake) : 120 x 120 x25 mm blue LED fan, 1300rpm, 17dBA, Rear (Exhaust) : 120 x 120 x25 mm blue LED fan, 1300rpm 17dBA.
2.2 Installing 5.25" Device Remove the drive bay cover from the selected position, then insert the device into the 5.25" drive bay 2.3 Installing 3.5" HDD ( For 12cm Fan Cage ) Remove thumb screws at both side and remove the fan cage Insert HDD by sliding HDD into the 12 cm fan cage. Secure HDD by tightening screws to HDD Finish installation Insert back the fan cage and tighten with thumb screws at both side.
2.4 Installing 3.5" Device to Drive Tray With Power Button Remove and slide drive bay out-ward to remove. Place cover back to drive tray to its original position. Insert 3.25" device and secure device with screw. Insert the device tray pictured above and secure the device tray by thumb screws. Squeeze both top and bottom portion of drive tray cover picture to the left to remove cover. Remove mesh from cover Drive tray with Power Button can be placed at any drive bay desired.
2.5 How to remove the fan & fan holder 2.
2.7 PCI slot tool-free function operation Open the plastic clip then take off the PCI bracket as follow. Chapter3 Motherboard & Leads Installation 3.1 Motherboard Installation Each motherboard has different standoff layout. It is highly suggested that you refer to your motherboard's manual when installing motherboard into the case. The case is applicable with Extend-ATX Standard ATX, Micro ATX motherboards. Your motherboard may require a special I/O Panel, which should be included with your motherboard.
3.2 Case LED connections 3.3 USB2.0 & IEEE1394 Firewire connection USB connection Please consult your motherboard manual to find out the section of "USB connection". USB2.0 Brank) On the front of the case, you can find some LEDs and switch leads (POWER SW*1, POWER LED*1, H.D.D. LED*1, RESET SW*1). Please consult user manual of your motherboard manufacturer, then connect these leads to the panel header on the motherboard.
3.4 Ear & MIC connections IEEE1394 Firewire connection Please consult your motherboard manual to find out the section of "IEEE1394 Firewire connection". Please consult your motherboard manual to find out the section of "front panel audio connector".
Chapter4 Other 4.1 Silent PurepowerTM power supply (optional) The Thermaltake Silent TM Purepower specification meets Intel Pentium 4 and AMD K7; it offers plenty of functions, which mainly include: 1.Automatic Fan Speed Control: The Silent Purepower TM power supply can detect the inside heat and automatically adjust the fan speed to provide adequate airflow. 2.Ultra Silent:Ball bearing fans with high reliability and super low acoustic noise under all load condition.
