Thecus N8800SAS User’s Manual
Copyright and Trademark Notice Thecus and other names of Thecus products are registered trademarks of Thecus Technology Corp. Microsoft, Windows, and the Windows logo are registered trademarks of Microsoft Corporation. Apple, iTunes and Apple OS X are registered trademarks of Apple Computers, Inc. All other trademarks and brand names are the property of their respective owners. Specifications are subject to change without notice. Copyright © 2009 Thecus Technology Corporation. All rights reserved.
Safety Warnings For your safety, please read and follow the following safety warnings: Read this manual thoroughly before attempting to set up your N8800SAS. Your N8800SAS is a complicated electronic device. DO NOT attempt to repair it under any circumstances. In the case of malfunction, turn off the power immediately and have it repaired at a qualified service center. Contact your vendor for details.
Table of Contents Copyright and Trademark Notice ................................................... 2 About This Manual ......................................................................... 2 Limited Warranty........................................................................... 2 Safety Warnings ............................................................................ 3 Table of Contents .......................................................................... 4 Chapter 1: Introduction .......
Language Selection .............................................................................26 System Information.............................................................................26 Product Information ..................................................................... 26 System/Service Status ................................................................. 27 Logs .......................................................................................... 28 System Management ..............
Snapshot .................................................................................... 69 Snap (Snapshot configuration).................................................................. 69 Folder and sub-folders Access Control List (ACL) ......................................... 70 Stackable NAS............................................................................. 72 ISO Mount .................................................................................. 77 User and Group Authentication..
Part II - Enable DDNS on the Router............................................. 116 Part III - Setting up Virtual Servers (HTTPS).................................. 116 Firewall Software Configuration ........................................................ 116 Replacing Damaged Hard Drives........................................................ 117 Hard Drive Damage.................................................................... 117 Replacing a Hard Drive ...............................................
Stripe Size ......................................................................................... 141 Disk Usage......................................................................................... 142 Appendix D: Active Directory Basics .......................................... 143 Overview ........................................................................................... 143 What is Active Directory? .................................................................. 143 ADS Benefits....
Chapter 1: Introduction Overview Thank you for choosing the Thecus N8800SAS IP Storage Server. The Thecus N8800SAS is an easy-to-use storage server that allows a dedicated approach to storing and distributing data on a network. Data reliability is ensured with RAID features that provide data security and recovery—over ten Terabyte of storage is available using RAID 5 and RAID 6.
Backup Server Don’t leave precious data to chance. With advanced backup capabilities, you can easily upload mission critical files to the N8800SAS, and even automate your backup tasks for true peace-of-mind. To find out how to backup your files with the N8800SAS, refer to Chapter 4: Backup >Nsync. Printer Server With the N8800SAS’s Printer Server, you can easily share an IPP printer with other PCs connected to your network.
z z z Screw Kit & Key-Luck x1 HDD Compatibility list Card x1 Multiple Languages Warranty Card x1 Please check to see if your package is complete. If you find that some items are missing, contact your dealer.
Front Panel The Thecus N8800SAS’s front panel has the device’s controls, indicators, and hard disk trays: Front Panel Item 1.Power Button • 2.Power LED • 3.Reboot Button • 4.System fan alarm • LED 5. Mute button • 6.USB Port • 7.Up Button ▲ 8.Down Button ▼ 9.Enter Button ↵ 10.Escape Button ESC Description Power on/off N8800SAS Solid green: System is power on. Press to system reboot Solid red: system fan failure notification Mute the system fan alarm. USB 2.
Hard Disk Trays Each of the N8800SAS’s hard disk trays has a lock, a latch, and two LED indicators: 1 2 3 4 5 Hard Disk Trays Item Description 1.HDD Power LED • Solid blue: hard disk is powered on 2.HDD • Blinking green: system is accessing data on the hard disk Access/Error LED 3.Lock • Use the lock to physically secure the hard disk to the unit 4.Latch • Use to open and remove or close and secure the tray 5.Handle • Pull out HDD tray Rear Panel The N8800SAS rear panel features ports and connectors.
5.Serial Port 6.WAN Port 7.
Chapter 2: Hardware Installation Overview Your N8800SAS is designed for easy installation. To help you get started, the following chapter will help you quickly get your N8800SAS up and running. Please read it carefully to prevent damaging your unit during installation. Before You Begin Before you begin, be sure to take the following precautions: 1. Read and understand the Safety Warnings outlined in the beginning of the manual. 2.
Cable Connections To connect the N8800SAS to your network, follow the steps below: 1. Connect an Ethernet cable from your network to the WAN port on the back panel of the N8800SAS. 2. Connect the provided power cord into the universal power socket on the back panel. Plug the other end of the cord into a surge protector socket. Press the power supply switch to turn on the power supply. 3. Press the power button on the Front Panel to boot up the N8800SAS.
Checking System Status After making connections on the N8800SAS and powering up, check whether the system status is normal or has trouble by observing indicators on the front panel and hard disk trays. System Status Normal The system status is normal if: The Power LED on the Front Panel glows green. The HDD Power LED on each HDD tray glows blue (assuming all disks are installed). 3. The default IP address of the WAN port is 192.168.1.100 on LCD. 1. 2. System Trouble The system has trouble if: 1.
Chapter 3: First Time Setup Overview Once the hardware is installed, physically connected to your network, and powered on, you can configure the N8800SAS so that it is accessible to your network users. There are two ways to set up your N8800SAS: using the Thecus Setup Wizard or the LCD display. Follow the steps below for initial software setup. Thecus Setup Wizard The handy Thecus Setup Wizard makes configuring N8800SAS a snap.
6. Name your N8800SAS and configure the network IP address. If your switch or router is configured as a DHCP Server, configuring the N8800SAS to automatically obtain an IP address is recommended. You may also use a static IP address and enter the DNS Server address manually. 7. Change the default administrator password. 8. Finished! Access the N8800SAS Web Administrator Interface by pressing the Start Browser button.
NOTE The Thecus Setup Wizard is designed for installation on systems running Windows XP/2000 or Mac OSX or later. Users with other operating systems will need to install the Thecus Setup Wizard on a host machine with one of these operating systems before using the unit. LCD Operation The N8800SAS is equipped with an LCD on the front for easy status display and setup. There are four buttons on the front panel to control the LCD functions.
2009/05/22 12:00 Disk Info RAID Current system time. Current status of disk slot has been installed Current RAID status. The N8800SAS will rotate these messages every one-two seconds on the LCD display. USB Copy The USB Copy function enables you to copy files stored on USB devices such as USB disks and digital cameras to the N8800SAS by press button. To use USB copy, follow the steps below: 1. Plug your USB device into an available USB port on the Front end. 2. In Display Mode, press the Down Button (▼).
Chapter 4: Web Administration Interface. Step 1: Network Setup From the Web Administration Interface, you can configure the network settings of the N8800SAS for your network. You can access the Network menu from the menu bar. For details on how to configure your network settings, refer to Chapter 4: System Network . Step 2: RAID Creation Next, administrators can configure their preferred RAID setting and build their RAID volume.
iTunes Server Media Server Printer Server Photo Server 23
Chapter 4: System Administration Overview The N8800SAS provides an easily accessible Web Administration Interface. With it, you can configure and monitor the N8800SAS anywhere on the network. Web Administration Interface Make sure your network is connected to the Internet. To access the N8800SAS Web Administration Interface: 1. Type the N8800SAS’s IP address into your browser. (Default IP address is http://192.168.1.100) NOTE Your computer’s network IP address must be on the same subnet as the N8800SAS.
Menu Bar Item System Information System Management System Network Storage User and Group Authentication Application Server Module Management Backup Description Current system status of the N8800SAS. Various N8800SAS system settings and information. Information and settings for network connections, as well as various services of the N8800SAS. Information and settings for storage devices installed into the N8800SAS. Allows configuration of users and groups.
Temperature. Network. Green: Systematic temperature is normal. Red: Systematic temperature is unusual. Click to go to System Status page as short cut. Green: Connection to network is normal. Red: abnormal connection to the network Logout Click to logout Web Administration Interface.
Product Information Item Description Manufacturer Displays the name of the system manufacturer. Product No. Shows the model number of the system. Firmware version Shows the current firmware version. Up time Displays the total run time of the system. System/Service Status From the Status menu, choose the System item, System Status and Service Status screens appear. These screens provide basic system and service status information.
NFS Status SMB/CIFS Status FTP Status Media Server Nsync Status UPnP Status SNMP The The The The The The The status status status status status status status of of of of of of of the the the the the the the Network File Service Server. SMB/CIFS server. FTP server. Media Server Nsync server. UPnP service. SNMP service. Logs From the System Information menu, choose the Logs item and the System Logs screen appears.
Truncate All Log File The number of lines per page □ Sort Ascending Sort Descending |<< < > >>| Clear all log files. Specify desired number of lines to display per page. Shows logs by date in ascending order. Shows logs by date in descending order. Use the forward ( > >>| ) and backward ( |<< browse the log pages. Re-loading logs. <) buttons to System Management The System Management menu gives you a wealth of settings that you can use to configure your N8800SAS’s system administration functions.
Notification configuration From the menu, choose the Notification item, and the Notification Configuration screen appears. This screen lets you have the N8800SAS notify you in case of any system malfunction. Press Apply to confirm all settings. See following table for a detailed description of each item. Notification Configuration Item Description Beep Notification Enable or disable the system beeper that beeps when a problem occurs.
Firmware Upgrade From the menu, choose the Firmware Upgrade item and the Firmware Upgrade screen appears. Follow the steps below to upgrade your firmware: 1. Use the Browse button to find the firmware file. 2. Press Apply. 3. The beeper beeps and the Busy LED blinks until the upgrade is complete. NOTE • The beeper only beeps if it is enabled in the System Notification menu. • Check Thecus website for the latest firmware release and release notes. • Downgrading firmware is not permitted.
See the following table for a detailed description of each item. UPS Setting Item UPS Monitoring Manufacturer Model Battery Status Power Seconds between power failure and first notification Seconds between subsequent power failure notifications Shutdown the system when the battery charge is less than Apply Description Enable or disable UPS monitoring. Choose the UPS manufacturer from the dropdowns. Choose the UPS model number from the dropdowns.
Example - Monday: On: 8:00; Off: 16:00 System will turn on at 8:00 AM on Monday, and off at 16:00 on Monday. System will turn on for the rest of the week. If you choose an on time, but do not assign an off time, the system will turn on and remain on until a scheduled off time is reached, or if the unit is shutdown manually. Example - Monday: On: 8:00 System will turn on at 8:00 AM on Monday, and will not shut down unless powered down manually.
From the menu, choose the WOL item, and the Wake-up On LAN screen appears. From here, you can Enable or Disable. Wake-up On LAN Configuration Item Description WOL Service Enable or Disable WOL service Apply Click Apply to save changes. SNMP Support From the menu, choose the SNMP item and the SNMP Support screen appears. You could enable the SNMP function and filled in the related information in each fields. With the SNMP management software could get system basic information.
See the following table for a detailed description of each item. Change Administrator and LCD Entry Password Item Description New Password Type in a new administrator password. Confirm Password Type the new password again to confirm. Apply Press this to save your changes. ˙ Config Mgmt From the menu, choose the Config Mgmt item and the System Configuration Download/Upload screen appears. From here, you can download or upload stored system configurations.
˙ Factory default From the menu, choose the Factory Default item and the Reset to Factory Default screen appears. Press Apply to reset the N8800SAS to factory default settings. WARNING Resetting to factory defaults will not erase the data stored in the hard disks, but WILL revert all the settings to the factory default values. ˙ Reboot & Shutdown From the menu, choose Reboot & Shutdown item, and the Shutdown/Reboot System screen appears.
To perform a file system check, click Apply. Once clicked, the following prompt will appear: Click Yes to reboot the system. Once the system has rebooted, you will be returned to the File System Check prompt. There you will see the available RAID volumes to run the file system check on except ZFS volume, ZFS has no need to perform file system check. Check the desired RAID volumes and click Next to proceed with the file system check. Click Reboot to reboot without running the check.
Click Start to begin the file system check. Click Reboot to reboot the system. When the file system check is run, the system will show 20 lines of information until it is complete. Once complete, the results will be shown at the bottom. NOTE The system must be rebooted before the N8800SAS can function normally after file system check complete.
System Network Use the System Network menu to make network configuration settings as well as service support settings. WAN Configuration From the System Network menu, choose WAN, and the WAN Configuration screen appears. This screen displays the network parameters of the WAN connection. You may change any of these items and press Apply to confirm your settings.
DNS Server NOTE Domain Name Service (DNS) server IP address. • Only use Jumbo Frame settings when operating in a Gigabit environment where all other clients have Jumbo Frame Setting enabled. • Enabling DHCP automatically turns on UPnP— see the Service Support Screen. • If you are only using the WAN port, we suggest that you disable IP Sharing Mode. This will result in higher throughput. • A correct DNS setting is vital to networks services, such as SMTP and NTP. • To use the Link Aggregation with “802.
DHCP Server Configuration A DHCP server can be configured to assign IP addresses to devices connected to the LAN port. To configure these ports, choose LAN from the System Network menu. DHCP Configuration Item Description DHCP Server Enable or disable the DHCP server to automatically assign IP address to PCs connected to the LAN interface. Start IP Specifies the starting IP address of the DHCP range. End IP Specifies the ending IP address of the DHCP range.
Samba Recycle Bin The N8800SAS is supported recycle bin via SMB/CIFS protocol. Simply enable it then all of deleted files/folders will reside in the “.recycle” folder with hidden attribution in each share. In general, Windows has default to invisible all of hidden folders/files. So please enable this option to view “.recycle” folder. Samba Anonymous Login Authentication To enable this option, no matter there is share folder has been created in public access.
NFS Setup From the System Network menu, choose the NFS item, and the NFS Support screen appears. The N8800SAS can act as an NFS server, enabling users to download and upload files with the favorite NFS clients. Press Apply to confirm your settings. A description of each item follows: NFS Apply NFS Server Setting Item Description Enable or Disable NFS support. Click Apply to save your changes.
A description of each item follows: FTP Item FTP Security FTP Port FTP ENCODE Allow Anonymous FTP Access Auto Rename Upload Bandwidth Download Bandwidth Description Enable FTP Service on the N8800SAS. Enable or disable Security FTP, be sure the client FTP software has also security FTP setting enabled. Specifies the port number of an incoming connection on a non-standard port. If your FTP client or operating system does not support Unicode (e.g.
A description of each field follows: Media Manager Settings Item Description Media Server Enable or disable the Media Server service. Shared Media Folders Select the folder(s) that contains media files to be shared. Rescan Click the Rescan button to have the N8800SAS for new contents in the selected media folder. Share Media Folders Once the Media Server software is installed, you can start adding folders that contain the media that you would like to share.
4. Setup the DMA (These steps will be different if you use a different DMA) a. From the Server List screen, select “N8800SAS: Media Server” as the server. b. Go to My Media c. Click on the Up/Down Arrow buttons to select Music Jukebox, Photo Albums, or Video Clips d. Start enjoying the contents stored in your N8800SAS. HTTP/ Web Disk From the System Network menu, choose the HTTP/ Web Disk item, and the Web Disk (HTTP) Support screen appears.
UPnP This device supports UPnP Media server, which allows users to play media files with UPnP client (ex. DMA devices). Enable or disable Universal Plug and Play protocol. UPnP helps to find the IP address of the N8800SAS. Nsync Target From the System Network menu, choose the Nsync Target item, and the Nsync Setting screen appears. Enable or Disable your Nsync Target Server. Press Apply to confirm your settings.
through Bonjour zero-configuration networking with a complete description of the protocols and technologies used to create Bonjour enabled applications and devices. Storage Management The Storage menu displays the status of storage devices installed in the N8800SAS, and includes storage configuration options such as RAID and disk settings, folder configuration, space allocation and ISO Mount. Disks Information From the Storage menu, choose the Disks item and the Disks Information screen appears.
Bad Block scan Total Capacity Disk Power Management NOTE Failed. Yes to start scan Bad Block. Shows the total SATA/SAS hard disk capacity. The administrator can set the disk to power down after a period of inactivity. (SATA HDD Only) When the Status shows Warning, it usually means there are bad sectors on the hard disk. It is shown only as a precaution and you should consider changing the drives. S.M.A.R.T.
Current Pending Sector (SATA HDD Only) Test Type (SATA HDD Only) Test Result (SATA HDD Only) Test Time (SATA HDD Only) NOTE reallocated, the more a decrease (up to 10% or more) can be noticed in disk read/write speeds. Current count of unstable sectors (waiting for remapping). The raw value of this attribute indicates the total number of sectors waiting for remapping. Later, when some of these sectors are read successfully, the value is decreased.
RAID Information Item Description Master RAID The RAID volume currently designated as the Master RAID volume. ID ID of the current RAID volume. NOTE: All RAID IDs must be unique. RAID Level Shows the current RAID configuration. Status Indicates status of the RAID. Can read either Healthy, Degraded, or Damaged. Disks Used Hard disks used to form the current RAID volume. Total Capacity Total capacity of the current RAID. Data Capacity Indicates the used capacity and total capacity used by user data.
2. On the RAID Configuration screen, set the RAID storage space as JBOD, RAID 0, RAID 1, RAID 5, RAID 6, or RAID 10 — see Appendix C: RAID Basics for a detailed description of each. 3. Specify a RAID ID. 4. If this RAID volume is meant to be the Master RAID volume, tick the Master RAID checkbox. NOTE In a multiple RAID configuration, one RAID volume must be designated as the Master RAID volume. The Master RAID volume will store all installed modules. If the Master RAID is changed to another location (i.e.
NOTE Building a RAID volume may take time, depending on the size of hard drives and RAID mode. In general, while the RAID volume building process is up to “RAID Building” then the data volume is capable to be accessed. WARNING Creating RAID destroys all data in the current RAID volume. The data is unrecoverable. With a RAID 1, RAID 5, RAID 6, or RAID 10 volume, you can also add a spare disk after the RAID is created. See Chapter 6: Tips and Tricks > Adding a Spare Disk for details.
RAID 6 RAID 10 WARNING RAID 5 requires a minimum of 3 disks. RAID 5 can sustain one failed disk. Two independent parity computations must be used in order to provide protection against double disk failure. Two different algorithms are employed to achieve this purpose. RAID 6 requires a minimum of 4 disks. RAID 6 can sustain two failed disks. RAID 10 has high reliability and high performance. RAID 10 is implemented as a striped array whose segments are RAID 1 arrays.
Remove RAID Click to remove the RAID volume. All user data and iSCSI has been created in selected RAID volume will be removed. To remove a RAID volume, follow the steps below: 1. On the RAID List screen, select the RAID volume by clicking on its radio button, and click RAID Information to open the RAID Configuration screen. 2. On the RAID Configuration screen, click Remove RAID. 3.
WARNING Remove RAID destroys all data in the current RAID volume. The data is unrecoverable. Expanding a RAID To expand a RAID 1, RAID 5, RAID 6, or RAID 10 volume, follow the steps below: 1. Replace one of the hard drives in the RAID volume and allow it to automatically rebuild. 2. Once rebuilt, you can continue to replace any remaining disks in the RAID array. 3. When you are done replacing hard drives, log on to Web Management. Navigate to Storage> RAID to open the RAID Configuration screen. 4.
Migrating a RAID Once a RAID volume has been created, you may want to move it to other physical drives or change the RAID array all together. To migrate a RAID 0, RAID 1, RAID 5 or RAID 6 volume, follow the steps below: 1. From the RAID Configuration screen, click Migrate RAID. 2. A list of possible RAID migration configurations will be listed. Select the desired migration scheme and click Apply. 3. The system will begin migrating the RAID volume.
NOTE Migrating a RAID volume could take several hours to complete With RAID level migration function, it has two different type “On line” and “Off line” alone with limitation as listed below. 1. During RAID level migration, it is not allowed reboot or shutdown system. 2. Off line RAID level migration, all services will stop and data is inaccessible. 3.
Below is a table listing of possible RAID migration schemes: To From RAID 0 RAID 5 RAID [OFFLINE] 0 [RAID 0] HDDx2 to [RAID 0] HDDx3 [RAID 0] HDDx2 to [RAID 5] HDDx3 [RAID 0] HDDx2 to [RAID 0] HDDx4 [RAID 0] HDDx2 to [RAID 5] HDDx4 [OFFLINE] RAID 6 X [RAID 0] HDDx2 to [RAID 0] HDDx5 [RAID 0] HDDx2 to [RAID 5] HDDx5 [RAID 0] HDDx2 to [RAID 0] HDDx6 [RAID 0] HDDx2 to [RAID 5] HDDx6 [RAID 0] HDDx2 to [RAID 0] HDDx7 [RAID 0] HDDx2 to [RAID 5] HDDx7 [RAID 0] HDDx3 to [RAID 0] HDDx4 [RAID 0] HDDx3 to [RA
RAID X [ONLINE] X [RAID 5] HDDx3 to [RAID 5] HDDx4 5 [RAID 5] HDDx3 to [RAID 5] HDDx5 [RAID 5] HDDx3 to [RAID 5] HDDx6 [RAID 5] HDDx3 to [RAID 5] HDDx7 [RAID 5] HDDx3 to [RAID 5] HDDx8 [RAID 5] HDDx4 to [RAID 5] HDDx5 [RAID 5] HDDx4 to [RAID 5] HDDx6 [RAID 5] HDDx4 to [RAID 5] HDDx7 [RAID 5] HDDx4 to [RAID 5] HDDx8 [RAID 5] HDDx5 to [RAID 5] HDDx6 [RAID 5] HDDx5 to [RAID 5] HDDx7 [RAID 5] HDDx5 to [RAID 5] HDDx8 [RAID 5] HDDx6 to [RAID 5] HDDx7 [RAID 5] HDDx6 to [RAID 5] HDDx8 [RAID 6] HDDx7 to [RAID
Item Modify Delete iSCSI Target Type Name Capacity Description Click this to modify the allocated space. Click this to delete the allocated space. Click to allocate space to iSCSI volume. Type of volume. Can be either USB or iSCSI. Name assigned to the volume. Capacity of the allocated space. Allocating Space for iSCSI Volume To allocate space for an iSCSI volume on the current RAID volume, follow the steps below: 1. Under the Volume Allocation List, click iSCSI Target.
Item RAID ID Allocation Unused iSCSI Target Volume Target Name Year Authentication Month Username Password Password Confirm Description ID of current RAID volume. Percentage and amount of space allocated to iSCSI volume. Percentage and amount of unused space on current RAID volume. Enable or Disable the iSCSI Target Volume. Name of the iSCSI Target. This name will be used by the Stackable NAS function to identify this export share. Select the current year from the dropdown.
2. Modify your setting. Press ok to change. Delete Volume To delete volume on the current RAID volume, follow the steps below: 1. Under the Volume Allocation List, click Delete. The Space Allocation screen appears.
2. Press YES. All data in the volume will be removed. Advance Option There are 2 options is currently allow Admin to Enable/Disable to operate N8800SAS associated with iSCSI setting. The details as listed in following screenshot. With the option changed, it will need to reboot system to activate. iSCSI Block Size Select the block size with 4K while the iSCSI volume size is over 2TB. iSCSI CRC/Checksum To enable this option, the initiator can connect with “Data digest” and “Header digest” enabled.
Adding Folders On the Folder screen, press the Add button and the Add Folder screen appears. This screen allows you to add a folder. After entering the information, press Apply to create new folder.
Add Folder Item RAID ID Folder Name Description Browseable Public Share Folder Limit Apply NOTE Description RAID volume where the new folder will reside. Enter the name of the folder. Provide a description the folder. Enable or disable users from browsing the folder contents. If Yes is selected, then the share folder will be browseable. Admit or deny public access to this folder. If Yes is selected, then users do not need to have access permission to write to this folder.
Description Browseable Public Share Limit Provide a description the folder. Enable or disable users from browsing the folder contents. This setting will only apply while access via SMB/CIFS and web disk. Admit or deny public access to this folder. Enter the maximum size of the folder. The folder will not grow beyond this limit. You can enter a 0 to turn off the share folder limit. Remove Folders To remove a folder, press the Remove button from the specified folder row.
NFS Share Item Hostname Privilege Guest System Support IO Mapping Apply Description Enter the name or IP address of the host Host has either read only or writeable access to the folder. There are two selections available: • Unix / Linux System • AIX (Allow source port > 1024) Choose the one which best fits your needs. There are three selections available: • Guest system root account will have full access to this share (root:root).
Snapshot The N8800SAS is capable for 16 snapshot version control. To have snapshot to work on, the file system creation for RAID volume has to be “ZFS”. Snap (Snapshot configuration) If added folder has located in the RAID volume with “ZFS” file system, then the folder management screen with “Snap” button will be configurable. Snapshot Item Take Shot Remove Schedule Description Click to take snapshot right away. Click to remove snapshot schedule. Click to open snapshot schedule setup screen.
These taken snapshot is only accessible though CIFS/SMB by manually type \\NAS IP address\snapshot and invisible from normal access. Also, the taken snapshot version is read only can not be deleted under CIFS/SMB access but only click the “Del” button showing on the screen shot above. Folder and sub-folders Access Control List (ACL) On the Folder screen, press the ACL button, and the ACL setting screen appears.
2. With the group or user selected, press one of the buttons from the three access level columns at the top. The group or user then appears in that column and has that level of access to the folder. 3. Continue selecting groups and users and assigning them access levels using the column buttons. 4. To remove a group or user from an access level column, press the Remove button in that column. 5. When you are finished, press Apply to confirm your ACL settings.
NOTE The system will list up to 1,000 users from the chosen category. To narrow your search, enter a search term in the blank provided. Stackable NAS The N8800SAS’s capacity can be expanded even further using the stackable function. With it, users can expand the capacity of their network storage systems up to 5 other stack target volumes which are located in different systems. These can be stacked through single network access like SMB or AFP acting as a share folder type.
Next, input the target IP address of the stackable device and click the Discovery button. The system will list available target volumes from the inputted IP address. Once IP with volume have been set, you may need to input a valid user name and password to validate your access rights. If there is no user name and password needed to access target volume, then leave it blank. Once IP with volume have been set, you may need to input a valid user name and password to validate your access rights.
From the figure above, the Export share name is “pmmeeting”. The figures below show the result before and after via Microsoft Network Access with settings have been completed. No Stack Target Stack target with export share name “pmmeeting” The Browseable setting will be same method of setting for system share folder. It designates whether or not this folder will be visible through web disk. You may refer the figures below for reference when Yes and No are selected.
The Public setting will be set same as what the setting for the system share folder associated with the ACL permission setup. If Public is set to Yes, all users will be able to access it, and ACL button will be grayed out. If Public is set to No, the ACL button will be available on the Stack Target List window. Click Apply to save your changes. B. Activate a Stack Target After your settings have been applied, the system will bring you back to Stack Target List window as shown below.
With this newly attached stack target device, you will see the information displayed and also several options you can choose. In general, if attached stack target device has been used by another N5200PRO/1U4500/N5500/N8800SAS/N8800/N8800 as stack target volume, then the Format item will be display and system will recognize it straight away and display its capacity. Otherwise, the Format item will be available and the Capacity and Status items will show as “N/A” and “Unknown file system” respectively.
ACL settings will be exactly the same as system folder that you may have setup previously. E. Reconnect a Stack Target The enabled stack target devices may be disconnected by situations such as power outages or network disconnects. When this happens, the Reconnect button will available. To attempt to reconnect the stack target, click Reconnect. ISO Mount The ISO Mount feature is very useful tool from Thecus products.
From the main menu, the ISO Mount feature is located under “Storage”. Please refer the figure below for reference. Select on the ISO mount function and you will have the screen shot appear as following. A. Add a ISO file From the figure above, select ISO file from drop down share list. After selection, system will bring up Mount table for further setting screen.
To mount new ISO file, select from listed ISO file and input desired mounting name into “Mount as:” field. Click “ADD” with confirmation to complete mounting ISO file. Or without “Mount as” ISO file export name input, system will automatic to give the export name by ISO file name. If left “Mount as:” blink then system will create mount point by ISO file name.
You could click “Unmount” to eliminate mounted ISO file. B. Using ISO The mounted ISO file will be located same share folder with name giving. Please refer the screen shot below. ISO file “image” has mounted as folder “Image” you could see. The ISO file “Thecus 01” without assign mounting name, system automatically has folder “Thecus 01” created. User and Group Authentication The N8800SAS has built-in user database that allows administrators to manage user access using different group policies.
A description of each item follows: ADS/NT Support Item Description Work Group / Domain Specifies the SMB/CIFS Work Group / ADS Domain Name (e.g. Name N8800SAS). ADS/NT Support Select Disable to disable authentication through Windows Active Directory Server or Windows NT. Authentication Method Select ADS for Windows Active Directory Server, or select NT for Windows NT ADS/NT Server Name Specifies the ADS/NT server name (e.g. adservername). ADS/NT Realm Specifies the ADS/NT realm (e.g. example.com).
AD Domain Example Item Information Work Group / Domain domain Name ADS Support Enable ADS Server Name Computer1 ADS/NT Realm Domain.local Administrator ID Administrator Administrator *********** Password NOTE • The DNS server specified in the WAN configuration page should be able to correctly resolve the ADS server name. • The time zone setting between N8800SAS and ADS should be identical. • The system time difference between N8800SAS and ADS should be less than five minutes.
2. On the Local User Setting screen, enter a name in the User Name box. 3. Enter a User ID number. If left blank, the system will automatically assign one. 4. Enter a password in the Password box and re-enter the password in the Confirm box. 5. Select which group the user will belong to. Group Members is a list of groups this user belongs to. Group List is a list of groups this user does not belong to. Use the << or >> buttons to have this user join or leave a group. 6.
Remove Users 1. Select an existing user from the Local User Configuration screen. 2. Click on Remove button and the user is deleted from the system. Local Group Configuration From the Accounts menu, choose the Group item, and the Local Group Configuration screen appears. This screen allows you to Add, Edit, and Remove local groups.
Local Group Configuration Item Description Add Press the Add button to add a user to the list of local groups. Edit Press the Edit button to modify a selected group from the system. Remove Press the Remove button to delete a selected group from the system. Add Groups 1. On the Local Group Configuration screen, click on the Add button. 2. The Local Group Setting screen appears. 3. Enter a Group Name. 4. Enter a Group ID number. If left blank, the system will automatically assign one. 5.
1. On the Local Group Configuration screen, select a group name from the list. 2. Press the Edit button to modify the members in a group. 3. To add a user into a group, select the user from the Users List, and press the << button to move the user into the Members List. 4. To remove a user from a group, select the user from Members List, and press the >> button. 5. Click the Apply button to save your changes. Remove Groups 1. On the Local Group Configuration screen, select a group name from the list. 2.
From the Accounts menu, click Batch Mgmt and the Batch Create Users and Groups dialogue will appear. To import your list of users and groups, follow these steps: 6. Click Browse… to locate your comma-separated text file. The information in the text file should follow this format: [USERNAME], [PASSWORD], [GROUP] 7. Click Open. 8. Click Import to begin the user list import. Application Server The N8800SAS supports printer server, and Tunes server.
Printer Information Item Description Manufacturer Displays the name of the USB printer manufacturer. Model Displays the model of the USB printer. Status Displays the status of the USB printer. Remove document Click to remove all documents from printer queue from Queue Restart Printer service Click to restart printer service If a corrupt print job is sent to a printer, printing may suddenly fail.
NOTE • Not all USB printers are supported. Please check Thecus website for a list of supported printers. • Note that if a multi-function (all-in-one) printer is attached to the N8800SAS, usually only the printing and fax functions will work. Other features, such as scanning, will probably not function. Windows Vista To set up the Printer Server in Windows Vista, follow the steps below: 1. Open Printer Folder from the Control Panel. 2.
3. Select Add a network, wireless or Bluetooth printer. 4. Select The printer that I want isn’t listed. You can press The printer that I want isn’t listed to go into next page without waiting for Searching for available printers to finish. 5. Click Select a shared printer by name.
Type http://:631/printers/usb-printer in the box, where is the IP address of the N8800SAS. Click Next. 6. Select or install a printer and then press OK. If your printer model is not listed, please contact your printer manufacturer for help. 7. Windows will attempt to connect to the printer. 8. You can choose to set this printer as the default printer by checking the Set as the default printer box. Click Next to continue.
9. Done! Click Finish. iTunes® Server With the built-in iTunes server capability, the N8800SAS enables digital music to be shared and played anywhere on the network! From the Network menu, choose the iTunes item, and the iTunes Configuration screen appears. You may enable or disable the iTunes Service from here. Once enabled, enter correct information for each field and press Apply to save your changes.
Module Management Module Installation From the Module Management menu, choose the Module Installation item and the Module Management screen appears. From here, you can install separate software modules to extend the functionality of your N8800SAS. System Module The system module is officially provided by Thecus for new features added. User Module The user module is reserved for Thecus fans to build up 3rd party functions in the future. Backup There are a number of ways to back up data with the N8800SAS.
Below is a description of each field: Nsync Item Add Edit Restore Del Task name Server Share folder Last Time Last Status Schedule Action Bandwidth Setting Description Click to add a Nsync task Click to Edit an Nsync task. Restore share folder from an Nsync target. Click to delete an Nsync task. Backup files on Nsync target is also deleted. The name of your Nsync task. The IP address of your target server The share folder you would want to backup. The time when the last Nsync task was executed.
Add Nsync Task Item Description Task Name The name of your Nsync task. Target Server Select whether the target is a Thecus Product (e.g. N8800SAS) or Manufacturer FTP server. Nsync Mode Synchronize mode or Incremental mode . Target Server IP The IP address of your target server. Address Source Folder The share folder you want to backup. Authorized Username The account name on the target server. on Target Server Password on Target The password for the username on the target server.
1. On the Nsync server, add a user for Nsync source (ex. nsyncsource1). For instructions on how to add a user on the N8800SAS, see Chapter 4: User and Groups Authentication> Local User Configuration > Add Users. 2. On the Nsync server, grant that user (ex. nsyncsource1) write access to the nsync folder. For instructions on how to set up a folder’s ACL, see Chapter 4: Storage management> Shore Folder> Folder Access Control List (ACL). 3.
1. Click Add to create a Backup task. The Add New Task dialog box appears. Add New Task Item Task Source Incremental Destination Excluded extensions Comments Description Specifies a name for the current task. Click to specify the source folder/file location. Click to specify whether the backup will be incremental. If unchecked, the backup will be a full backup. Click to specify the destination folder/file location. Files with these file name extensions will be skipped and not back up to the destination.
5. Find and select the drive that specifies your N8800SAS as your backup destination and click Next. 6. Click Next to display the wizard’s final page and click Finish to start backing up. Apple OS X Backup Utilities Mac OS X does not include any backup software.
Chapter 5: Using the N8800SAS Overview Once the N8800SAS is setup and operating, users on the network may manage all varieties of digital music, photos, or files by simply using their web browsers. To manage your personal files or access public files on the N8800SAS, just enter its IP address into your browser (default IP address is http://192.168.1.100), and you will be taken to the N8800SAS Login page.
6. To create a new folder within the current folder, press the New folder button. When the screen appears enter a name for the folder. Press OK to create the folder. 7. To upload a file from your computer to the current folder, press the New file (upload) button. When the screen appears, press Browse and locate the file to upload. Press OK and the file is uploaded to the current folder. 8. To delete a file or folder, select the file or folder’s check box. Press the Delete selected items button.
(Admin) Change password and confirm new password. (logout) To logout of the web disk interface. Show the files and folders in the directory. Search files in the directory. (You can only input some word string.) Name Displays the names of folders and files. Size Shows the size of folders and files. Type Displays the type of folders and files. Modified Shows the time of most recent modification of folders and files. owner Owner of the file.
Windows XP Publishing Wizard There are many ways for a local user to upload pictures into their photo album. Users of Windows XP can upload their pictures using the Windows XP Publishing Wizard. 1. Click on the XP Publishing Wizard icon on top right corner. 2. The XP Web Publishing Wizard Client screen appears. Click on the link to install the Publishing Wizard. 3. Windows XP will ask whether you want to run or save this file. Click Save to save the register file.
4. Once the register file is installed, use the Windows file manager to browse the folder that contains the picture you want to publish. On the left pane, there will be an icon labeled “Publish this folder to the Web”. 5. Click on this icon and Web Publishing Wizard will start. 6. Select the pictures you want to publish to the Photo Web Server by placing a check mark on the top left hand corner of the picture. Click Next.
7. Your PC will start to connect to the Photo Web Server. 8. Select N8800SAS Photo Gallery Wizard to publish your pictures to the N8800SAS. 9. Login into the N8800SAS with your local user name and password. 10. Create your album by entering an album name and clicking on the Create Album button.
11. Select the album you want to upload your pictures to. 12. Confirm the target album. 13. Windows will show you that the picture upload is in progress.
14. When the upload is finished, the Wizard will ask you whether if you want to go to the website. Click Finish to go to your Photo Web Server. 15. Click on the user’s icon to go to that user’s album. 16. You will see the user’s album list. Click on Album.
17. Finished! You will see the pictures just selected in the album. Managing Albums and Photos Icon Function Description Make Cover Make selected photo your cover picture. Back Return to the previous screen. Add Add a new album or photos. Modify Edit the name and description of the selected album or photo. Each name is limited to 20 characters and each description is limited to 255 characters. Delete NOTE Delete the selected albums or photos. • Only logged in users will see these icons.
Creating Albums To create a photo album, follow the steps below: 1. Click the Add button to create a new album. 2. Enter a name for the album, and enter a description if you wish. Then, click on the Create Album button. Password Protecting Albums If you would like to put a password on a particular album, follow these steps: 1. Select the album to be protected, click on the Edit button, and the Album Edit screen will appear. 2.
Slide Shows Slide shows are a great way to enjoy pictures stored on your N8800SAS. You can click on the Start Slide Show icon on the top right hand corner to start the slide show. To stop the slide show, click on the Stop Slide Show icon on the top right hand corner. Mapping a Client PC to the N8800SAS You can map share folders on the N8800SAS so that you can access them as if they were drives on your computer. You can connect to the shared network folders on the N8800SAS as follows: Windows 1.
1. Choose Go > Connect to Server… 2. Enter the network address for the server in the Server Address text box. When connecting using SMB/CIFS protocol, type: smb://192.168.1.100/Folder1 When connecting using AFP protocol, type: afp://192.168.1.100/Folder1 Click Connect. 3. When MAC OS X is trying to connect N8800SAS, it will ask for a User Name and Password which has access to the folder. 4.
3. You will now install the iSCSI Initiator using the Setup Wizard. Click Next to continue. 4. Leave the default selections and click Next. 5. Read the license agreement. To continue with the installation, click I Agree and then click Next. 6. The iSCSI Initiator will now install automatically. Click Finish once completed.
7. Start the iSCSI Initiator by double-clicking its icon on the desktop. The iSCSI Initiator properties window will appear. 8. Select the Discovery tab. Under Target Portals, click Add. 9. Enter the IP address of the N8800SAS. Click OK. 10. On the iSCSI Initiator Properties window, select the Targets tab. With the iSCSI target highlighted, click Log On. The Log On to Target dialogue will appear.
11. If you have not enabled CHAP, click OK to continue. If you have enabled CHAP, click Advanced. Under Advanced Settings, check the CHAP login information checkbox and enter your username and password. Click OK. 12. Right click My Computer on the desktop and select Manage.
13. Click on Disk Management and you will see a new hard disk listed. 14. Initialize the new hard disk and you will then be able to use the iSCSI target as a local drive. Windows Vista Because Windows Vista has the Microsoft iSCSI Initiator pre-installed, you will not have to install this piece of software. Instead, start the iSCSI Initiator and follow steps 8-14 to map the N8800SAS as an iSCSI drive.
Chapter 6: Tips and Tricks USB and eSATA Storage Expansion The N8800SAS supports external USB hard disks through its four USB ports. Once a USB hard disk has successfully mounted, the entire volume will be linked automatically to the default USB HDD folder. The N8800SAS supports up to 4 USB external storage devices. All file names on the USB disk volume are case sensitive. The N8800SAS also supports eSATA hard disks with its eSATA port.
Part I - Setup a DynDNS Account 1. Go to http://www.dyndns.org from your home PC. 2. Click on the Sign Up Now link. 3. Check the Check boxes, select a user name (i.e.: N8800SAS), enter your email address (i.e.: xxx@example.com), check Enable Wildcard, and create a password (i.e.: xxxx). 4. Wait for an email from www.dyndns.org. 5. Open the email and click on the link to activate your account Part II - Enable DDNS on the Router 1.
Replacing Damaged Hard Drives If you are using RAID 1, RAID 5, or RAID 6 you can easily replace a damaged hard drive in the Thecus N8800SAS while keeping your data secure with the system’s automatic data recovery. Hard Drive Damage When a hard drive is damaged and data in the RAID volume, the system LCD will display warning message also the system beeps. Replacing a Hard Drive To replace a hard disk drive in the N8800SAS: 1. Remove the tray with the damaged hard disk. 2.
Chapter 7: Troubleshooting Forgot My Network IP Address If you forget your network IP address and have no physical access to the system, you can find out the IP address by either looking directly onto the N8800SAS’s LCD panel, or by using the setup wizard to retrieve the IP of your N8800SAS. 1. Start the Setup Wizard, and it will automatically detect all Thecus IP storage products on your network. 2.
4. Set the Date, Time, and Time Zone. 5. Click Apply. In addition, if the N8800SAS is able to access the Internet and you want to keep the NTP Server clock.isc.org by default, please make sure the DNS Server is correctly entered, thereby allowing the NTP Server name to correctly resolve. (See System Network > WAN > DNS Server) Dual DOM Supports for Dual Protection The most advance and useful of N8800SAS is Dual DOM implemented. In the normal circumstance, it has no need to have this feature involved.
Chapter 8: Revision updated (FW 3.00.03 to 3.00.04) What’s New There are additional features implemented into the new 3.00.04 version firmware. RAID Expansion for iSCSI Target Volume First, the iSCSI volume is now able to expand its capacity from unused space. From the volume list, simply select the iSCSI volume you like to expand and click the Expand button: You will then see the dialog box displayed below. Drag the Expand Capacity bar to the size you want. Then press Expand to confirm the operation.
RAID Volume Encryption With firmware v3.00.04, you can protect your data by using RAID Volume Encryption function to prevent the risk of data exposure. To activate this function, the Encryption option needs to be enabled while the RAID is created and followed by password input for identification. Also, an external writable USB disk plugged into any USB port on the system is required to save the password you have entered while the RAID volume is being created. See the screenshot below for details.
NOTE 1. With RAID volume encryption enabled, the system performance will goes down. 2. With RAID volume encryption enabled, RAID volume expansion will operated in off line mode. RAID volumes with encryption enabled will be displayed with a key lock symbol next to volume ID name. iSCSI Thin-Provisioning An advanced thin-provisioning for iSCSI feature is available in this firmware release. With this function, the iSCSI capacity can be more flexible and more efficiently serve more users.
Next, setup the physical capacity for iSCSI thin-provision volume by dragging the Allocation bar to the desired size. After the size has been determined, click OK to confirm. Now you will see the iSCSI thin-provisioning volume is available from the list. Please refer to the screenshot below.
Now you can start to create iSCSI targets to join the newly-created iSCSI thin-provision volume. Basically, the iSCSI target under iSCSI thin-provisioning has exactly same settings screen as the standard iSCSI target volume creation. The only difference is the “Virtual Size” of capacity. Unlike creating standard iSCSI target volumes, the capacity has been physically allocated. The iSCSI target volume creation under thin-provisioning can virtually be up to 16000GB (16TB). Let’s take the example below: 1.
The screen shot for iSCSI target volume creation under thin-provisioning; the physical capacity 333.8GB. The screen shot to setup an iSCSI target volume under thin-provisioning of 1700GB. iSCSI target volume creation. The maximum virtual size is 14300GB (16000GB – 1700GB(1st iSCSI target volume)).
This screenshot lists iSCSI target volumes created under thin-provisioning. The 2nd iSCSI target volume under thin-provisioning has been created with a capacity of 14300GB. This message appears if there is no more room for new iSCSI target creation. NOTE 1. Each RAID volume can only create one iSCSI thin-provision volume. 2. Each thin-provision volume can only create 5 iSCSI target volumes. 3. The notification will send out while the physical size of iSCSI thin-provision capacity has used up to 90%.
Error Corrections None 127
Chapter 9: Revision updated up to FW 3.00.08 What’s New There are additional features implemented into the new 3.00.08 version firmware. Updated Login User Interface There is a brand new design for the admin login UI. NOTE The previous chapters have screenshots of the original user interface. Please note that all changes are visual only. There are no functional changes.
Disclaimer Page Added The following disclaimer page has been added to this firmware release. Please click the check box if you do not want to have this page displayed during the next login.
Updated Main User Interface The look and icons of the main user interface have been updated. Add On-Line Register Service From main menu tree, there is a new “On-line Register” option added with this firmware release. This on-line register service can periodically update the user when new firmware and software modules are released by Thecus. To enable this service, simply check the “Enable” check box. By enabling this service, the items in bold will be sent to Thecus via the Internet.
Added Rsync Setting under Nsync Target The Thecus Nsync feature has added a third way to use Rsync to replicate data between two systems. For the target side to allow source cross data, the Rsync target server needs to first select “Enable” and then assign a username and password for authentication. NOTE The Rsync target server username and password is used for this replication feature only. It is not related to the standard local user.
enable the sync target server and input a valid username and password to grant access permission. Added 2nd Gateway for Clients of DHCP Server Route The adding of a 2nd gateway has been phased in to serve clients that use their Thecus NAS as a DHCP server to have another route to balance traffic bandwidth. NOTE If the IP sharing mode setting is set to “Enable” under WAN port, then this 2nd gateway cannot be configured.
Added Dual DOM for Auto Repair The unique Dual DOM feature can now perform “Auto Repair”. The Thecus NAS will backup up to five versions of the system configuration either by the default timing of 1:00am every day automatically or as scheduled by the user. This unique “Auto Repair” will be triggered if the primary DOM has a booting issue. In this instance, the 2nd DOM will take over the boot function.
Chapter 10: Version 3.01.00 Firmware Updates What’s New There are additional features implemented into the new 3.01.00 version firmware. Updated Login User Interface The design of the admin login UI has been completely updated. NOTE The previous chapters have screenshots of the original user interface. Please note that all changes are visual only. There are no functional changes. Updated Main User Interface The look and icons of the main user interface have been updated.
Administrators can add or remove favorite functions to My Favorites by right clicking the mouse on the menu tree. The other way administrators can add favorite functions is by clicking the “Add Favorite” icon in each function screen. Please refer figure below in red circuit icon. To return to the favorite screen, simply click “My Favorite” located at the left hand corner of the main screen.
Added Additional Mode Support for Link Aggregation Link Aggregation now has six supported modes. The administrator can choose the most suitable mode to fit the network environment. You may choose from the following options: z z z z z z z Disable Load Balance Failover Balance-XOR 802.3ad Balance-TLB Balance-ALB See the right diagram for details.
Appendix A: Product Specifications Hardware Specifications Product Model Network Interfaces WAN LAN Storage HDD Bays eSATA I/O Interfaces USB Ports System Information LCD Control Panel System LED Display Physical Height Width Depth Power Supply Security Environment Temperature Humidity Certifications N8800SAS Gigabit RJ-45 connector Gigabit RJ-45 connector 8 x 3.
iSCSI Target Folder Management Quota Management Backup System Management Event Notification UPS Support Printer Server Supported USB Devices Setup Utility Disk roaming RAID level migration RAID expansion Supports: Microsoft iSCSI Initiator v2.0.4 StarPort Initiator V3.5.2 MAC OS: globalSAN iSCSI initiator version 3.0 (1150) Linux: open-iscsi 2.
Appendix B: Customer Support If your N8800SAS is not working properly, we encourage you to check out Chapter 7: Troubleshooting, located in this manual. You can also try to ensure that you are using the latest firmware version for your N8800SAS. Thecus is committed to providing free firmware upgrades to our customers. Our newest firmware is available on our Download Center: http://www.thecus.com/download.
Appendix C: RAID Basics Overview A Redundant Array of Independent Disks (RAID) is an array of several hard disks that provide data security and high performance. A RAID system accesses several hard disks simultaneously, which improves I/O performance over a single hard disk. Data security is enhanced by a RAID, since data loss due to a hard disk failure is minimized by regenerating redundant data from the other RAID hard disks.
RAID 5 RAID 5 offers data security and it is best suited for networks that perform many small I/O transactions at the same time, as well as applications that require data security such as office automation and online customer service. Use it also for applications with high read requests but low write requests. RAID 5 includes disk striping at the byte level and parity information is written to several hard disk drives.
Disk Usage When all 7 disks are of the same size, and used in RAID, N8800SAS disk usage percentage is listed below: RAID Level Percentage Used RAID 0 100% RAID 1 1/n x 100% RAID 5 (n-1)/n x 100% RAID 6 (n-2)/n x 100% RAID 10 50% JBOD 100% n：HDD number 142
Appendix D: Active Directory Basics Overview With Windows 2000, Microsoft introduced Active Directory (ADS), which is a large database/information store. Prior to Active Directory the Windows OS could not store additional information in its domain database. Active Directory also solved the problem of locating resources; which previously relied on Network Neighborhood, and was slow. Managing users and groups were among other issues Active Directory solved.
Appendix E: Licensing Information Overview This product included copyrighted third-party software licensed under the terms of GNU General Public License. Please see THE GNU General Public License for extra terms and conditions of this license. Source Code Availability Thecus Technology Corp. has exposed the full source code of the GPL licensed software. For more information on how you can obtain our source code, please visit our web site, http://www.thecus.com.
CGIC License Terms Basic License CGIC, copyright 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004 by Thomas Boutell and Boutell.Com, Inc. Permission is granted to use CGIC in any application, commercial or noncommercial, at no cost. HOWEVER, this copyright paragraph must appear on a "credits" page accessible in the public online and offline documentation of the program.
they have is not the original, so that any problems introduced by others will not reflect on the original authors' reputations. Finally, any free program is threatened constantly by software patents. We wish to avoid the danger that redistributors of a free program will individually obtain patent licenses, in effect making the program proprietary. To prevent this, we have made it clear that any patent must be licensed for everyone's free use or not licensed at all.
these conditions, and telling the user how to view a copy of this License. (Exception: if the Program itself is interactive but does not normally print such an announcement, your work based on the Program is not required to print an announcement.) These requirements apply to the modified work as a whole.
4. You may not copy, modify, sublicense, or distribute the Program except as expressly provided under this License. Any attempt otherwise to copy, modify, sublicense or distribute the Program is void, and will automatically terminate your rights under this License. However, parties who have received copies, or rights, from you under this License will not have their licenses terminated so long as such parties remain in full compliance. 5.
9. The Free Software Foundation may publish revised and/or new versions of the General Public License from time to time. Such new versions will be similar in spirit to the present version, but may differ in detail to address new problems or concerns. Each version is given a distinguishing version number.
