INSTRUCTION MANUAL ST - R E A D Y- T -F LY AL O (A036) O M 1/4 SUPER CUB Requires:2-stroke 0.91 or 4-stroke 1.20-1.60 engine, 5-channel radio w/ 6 standard servos Specifications Wing Span Wing Area Flying Weight Fuselage Length 104in / 2640mm 1586sq in / 102.3sq dm 14 lbs / 6300g 68 in / 1725mm * Specifications are subject to change without notice.* Warning ! This model is not a toy. It is designed for maximum performance.
1/4 SUPER CUB INDEX BEFORE YOU BEGIN P. 1 PARTS LIST P. 2 ASSEMBLY P. 3 -13 SAFETY PRECAUTIONS P.13 BEFORE YOU BEGIN 1 Read through the manual before you begin, so you will have an overall idea of what to do. 2 Check all parts. If you find any defective or missing parts contact your local dealer. Please DRY FIT and check for defects for all parts that will require CA or Epoxy for final assembly.
Parts List 1.MAIN WING -- 1 pair 2.PUSHROD Ø1.8x120mm w/ Threads(For Aileron & Flap Servo) -- 4 pcs FUEL TUBE Ø6x5mm -- 8 pcs STRAPER PL4112102 -- 4 pcs SCREW PB 2x30mm -- 12 pcs SCREW PWA2x8mm -- 16 pcs SERVO MOUNTING PANEL--4 pcs CLEVIS PL4112103-- 4 pcs TRI-HORN M3x22mm(L) PL4111251 -- 4 sets 3.SCREW PM3x15mm -- 12 pcs WASHER d3xD7mm -- 16 pcs M3 NUT -- 4 pcs MAIN WING STRUTS -- 1 set WING STRUT WIRE Ø3x143x208mm -- 2 pcs PLASTIC WIRE BRACKET PL5330030 -- 8 pcs 4.FUSELAGE -- 1 pc.
1 Main Wing Aileron & Flap Servo Lead Bottom View Pre-glued 2 Aileron & Flap Servo Ø1mm pilot holes for The Wings Maker tri- horn are pre-drilled. Please look for pin-hole marks at under side of control surfaces. PB2 x 30mm Screw 12 PWA2 x 8mm Screw TWM PL8210010 CLEVIS WRENCH 16 1mm PWA 2 x 8mm PWA 2 x 8mm PB2x30mm Straper Fuel Tube Ø6x5mm Clevis Fuel Tube Ø6x5mm Tri-horn Pushrod M3x22mm Ø1.8x120mm 1mm 1mm Bottom View P.
3 Wing Struts M3 x 15mm 69mm 193mm Screw 69mm 202mm 12 d3xD7mm Washer Main Wing Strut 380mm M3x15mm Washer d3xD7mm 16 M3 369mm M3 x 15mm Nut 4 d3xD7mm Washer Plastic Wire Bracket M3 Nut Bottom View 4 Stabilizer & Elevator (Stabilizer) B B' (Main Wing) B=B' Temporary install the main wing, adjust leveling of the stabilizer to make it as parallel to the main wing as possible. Pre-glued COMPLETED 5 Vertical Fin & Rudder C C C C Pre-glued COMPLETED P.
Tail Landing Gear PA3x14mm Screw 3 PWA2x12mm Screw 3 PA3x14mm 3.1mm Collar Set Screw M3x3mm M3x3mm Set Screw 1.5mm 1.5mm Copper Plate 1x10x40mm Bottom View 7 Main Landing Gear PA3 x12mm Screw 14 PA3x12mm Aluminum Plate 2mm PM3 x 13mm Screw 2 d3xD7mm Washer 2 d3xD7 Washer PM3x13mm PM3x13mm 1.5mm Front Bottom View 8 Main Landing Gear PA1.
9 Engine Mount M4x30mm Socket Head Screw 4 7.5mm 5.5mm Engine Mount PL 5111080 D4.2xD14.5mm Washer 4 M4 Blind Nut Washer d4.2xD14.5mm 4 Determine the angle of installation of the engine mount so the muffler will not contact the fuselage. Socket Head Screw M4 x 30mm 10 Engine M4x35mm Socket Head Screw M4 NYLON INSERT LOCK NUT D4xD12mm Washer 4 d4xD12mm Washer 8 M4 NYLON INSERT LOCK Nut 4 d4xD12mm Washer ANTI-VIBRATION MOUNT INSTALLATION 1 Copper Tube d4.1xD5x67.
11 Cowling First insert the grommet to the cowling then apply screw. PWA2 . 6x12mm Screw 4 d1.5xD6.5mm Silicon Grommet 4 Please refer to the attached sheet for usage of the transparent 3D template. Silicon Grommet d1.5xD6.5mm PWA2.6x12mm Fuselage Fuel Filler PL8110030 Cowling COMPLETED 12 Fuel Tank Cable Tie 1.5x5x400mm UP INSIDE VIEW Double-sided Tape 40x100mm Fuel Tank 500cc P.
13 Elevator Pushrod PB2x16mm Ø1mm pilot holes for The Wings Maker tri- horn are pre - drilled. Please look for pin - hole marks at under side of control surfaces. Screw 6 65mm 186mm PB2x16mm Tri-horn M3x22mm Bottom View Clevis Fuel Tube Ø6x5mm TWM PL8210010 CLEVIS WRENCH 14 Rudder Pushrod PB2x16mm Ø1mm pilot holes for The Wings Maker tri - horn are pre - drilled. Screw 3 145mm 43mm Clevis PB2x16mm Fuel Tube Ø6x5mm Tri-horn M3x22mm Bottom View TWM PL8210010 CLEVIS WRENCH P.
15 Flying Wire PM2x16mm Screw Copper Tube 6 PM2x8mm Screw 4 M2 Nut Press down the center 1/3 portion d2xD5mm 6 2mm Washer 6 3mm mm 16 x M2 M2 Nut PM2x8mm P d2.5xD3.2x8mm 2mm Clevis PM2x8mm d2.5xD3.2x8mm d2xD5mm COPPER PLATE 1x10x40mm M2 Nut 16 Windows Window A Window B COMPLETED COMPLETED Securely glue the windows to the fuselage. 17 Servo Set 3x3mm Set Screw 3x3mm Set Screw 1 Linkage Connector 1 M2 Nut 1 2mm Washer 2 2mm Washer 2mm Washer 2m m Throttle Servo.
18 Radio Equipment I nstall and arrange the servos as s hown in the diagram. Sponge Elevator Push rod Ø1.8x85mm M2 Nut Receiver Pushrod Connector Battery Plastic Tube d2xD3x300mm Elevator Servo KM 2x8mm J1 ( Pushrod Ø1 . 8x85mm ) J1 Throttle Servo J2 J2 ( Pushrod Ø1 . 8x1000mm ) Plywood 3x153x210mm Throttle Pushrod D1.2x480mm Charge Receptacles KP0041300 19 Pilot PWA 2x12mm Screw PWA 2x12mm Screw PC001102A 20 Wind Shield PWA2.3x12mm Screw 4 d1.5x6.
21 Main Wing M3 x 8mm Set Screw 4 Wing Tube Ø16x661mm WireØ0.8mm Set Screw M3x8mm Long slot Wing Tube Short slot Self Tightening Wing Latch Wing Tube Set Screw M3X8mm PWA2.3x12mm Completed P.
22 Wing Struts M3 x 8mm Socket Head Screw 2 d3xD7mm Washer 4 M3 Nylon Inert Lock Nut Washer d3xD7mm Screw M3x8mm 2 M3 NYLON INSERT LOCK NUT 23 Wing Setting Adjust the wing and fuselage configuration as shown in the diagrams. A' A B B' C C' P.
24 Control Throws Adjust the control throws as shown in the diagram. These throws are good for general flying. You can adjust according to your personal preference. Rudder 55mm 55mm Elevator 40mm 40mm Flap s (nea r fuse lage) 40mm Ailerons(away from fuselage) 20mm 20mm 10 2 mm 4.0 in. 25 C . G . 10 2 mm 4.0 in. C.G. http://www.theworldmodels.com/para/instruction/instructionManuals.php Warning! Important Safety Precautions # First time flyer should never fly by himself / herself.
LINKAGE CONNECTOR HW7111050 & HW7111060 Drill 2mm hole at servo horn. Insert linkage connector into servo horn. Make sure shoulder of screw is cleared from servo horn. Add washer to reduce play if necessary. Shoulder Tighten up the round nut against the shoulder. Apply CA or permanent thread locker. After fastening the round nut, make sure that the linkage connector can rotate freely.
Usage of the transparent 3D template This transparent 3D template is used for position guidance of the actual cutting of the pre-painted cowling. 1 2 3 4 Simply cut the transparent 3D template to fit your engine and exhaust pipe, then slide onto the actual cowling and use as template to mark the openings required for final cutting.
Code No. Size Package Code No. Size Package Code No. Size Package Code No. Size Package Small Clevis Code No. Size Package Special tool for clevis installation. Suitable for standard and small (EP)clevis. KP0041300 Code No SV4031 Code No.
