BED ORIGINAL DEAR INSTRUCTION MANUAL CUSTOMER, Thank you for choosing our product. Please read this manual carefully before assembling or using the product, to avoid damage caused by improper use. If the product is passed on to third parties, this manual should be passed on along with the product. If you have any questions, please don’t hesitate to contact us.
TABLES OF CONTENTS 1.Wireless Remote Instruction---------------------------------4 2.Parts List---------------------------------------------------------7 3.
Specifications Actuator rating: 24V,3A (Max) Max.
Wireless Remote Instruction a.
W W U slide down the back cover Install the battery slide up the back cover Please install the battery(U) as shown, pay attention to the battery polarity. I if you can't slide off the back covers smoothly , use hammer or other heavy stuff to knock the edge slowly.
b. Build connection I then 1. Press the 2 button on remote control at same time: head up, foot down. 2. Keep press the botton on reomote control and press the code match key on motor. 3. When you hear "didi" sound, the match get succeed. Now you can use remote control to lift and lower the bed. I white slider block Before attaching motor to bed frame, make sure the white slider block stays invisible, If not,press the S6 button. c.
PARTS A LIST 1× B LEFT BRACKET D 1× C RIGHT BRACKET 4× E CROSS BEAM 2× F BED FOOT WITH LONG SCREW BED FOOT WITH SHORT SCREW G 1× H LEFT LEG J 2× HEAD BAR 1× I 1× RIGHT LEG 2× K MOTOR 1× L 1× L K DRIVING LEVER 2× HEAD BOARD 7 BACK BOARD
M 1× N 1× O N M HIP BOARD P TAIL BOARD 4× T GIRTH EDGE V End BOARD 2× Q FOOT BOARD S O FOUNDATION BOARD 1× Q 1× R P 1× GIRTH EDGE 1× U RETAINERBAR 1× W 1× BATTERY 1× X 1× INSTRUCTION MANUAL REMOTE CONTROL Cloth COVER Y1 4× Y2 18× Y3 2× M10*30 M8*35 8 M8*55
Y4 2× Y5 M8 Y7 2× Y6 PLASTIC GASKET 1× Y8 13MM O PEN END WRENCH 8MM SPANNER 1× Y9 5MM SPANNER 9 1× 4× FINGER COVERS
Assemble the Frame Please check that you have all the parts listed before you do not continue assembly, please contact us immediately.
2 Build lift bars H G J J The head of two driving(J) levers are aligned. F F The left and right bars(F,G,H) are connected with the driving lever, lever(J), please align the arrows as indicated.
3 Connect Foot Lift bars on Frame Base G 2 A Foot 1 2 H 1 Head B 2 1 Y3 Y8 Y5 Y9 Y4 Y1 Y6 Assemble the circled part , pls check circle 1; 12 Plastic gasket Y7 G Assemble the square part, pls check square 2.
4 Connect Head Lift Bars on Frame Base A Foot 1 F Head B 1 F 1 Y9 Y1 Y6 Assemble the circled part , pls check circle 1; 13
Mount motor 5 J I I J 1. Slide off the motor(I) back covers. Put the motor slots on the driving lever tube Enfold the driving lever into the motor I Foot J Slide up to close I Head 2.Insert the motor into the driving lever, please pay attention to the direction of the motor, check the mark head and foot. Then buckle the back covers into place. If the back covers don’t slide in,lift the driving lever until it slides in.
Mount bed boards 6 K L Head M Y2 N O P Q Foot Y2 Y8 Turn the bed frame over,then place the 7 bed boards in the direction of the arrows and screw them with M8*35(Y2) screws.
Attach girth edge 7 Head S S R S Foot S R Under the front and back edges, attach two girth edges(S,R) edges last.
8 Put on cloth cover X Velcro Velcro Velcro X Pay attention to the front and back direction of the cloth cover; There are two holes behind the cloth cover. Raise the head to put on the cloth cover,put down the head after all the cornor are wrapped.
Push the retainerbar 9 Place the remote control T At the end of the bed,push the retainerbar into the plastic slider Dry clean Steam ironing Do not twist dry Do not wash 18
