VM-100 voltage meter user manual
Musikhaus Thomann Thomann GmbH Hans-Thomann-Straße 1 96138 Burgebrach Germany Telephone: +49 (0) 9546 9223-0 E-mail: info@thomann.de Internet: www.thomann.de 28.07.
Table of contents Table of contents 1 General notes............................................................................................................................................... 4 2 Safety instructions..................................................................................................................................... 7 3 Features..............................................................................................................................................
General notes 1 General notes This user manual contains important information on safe operation of the device. Read and follow all safety notes and all instructions. Save this manual for future reference. Make sure that it is available to all persons using this device. If you sell the device, include the manual for the next owner. Our products are subject to a process of continuous development. We therefore reserve the right to make changes without notice.
General notes Signal word Meaning DANGER! This combination of symbol and signal word indicates an immediate dangerous situation that will result in death or serious injury if it is not avoided. WARNING! This combination of symbol and signal word indicates a pos‐ sible dangerous situation that can result in death or serious injury if it is not avoided.
General notes Warning signs Type of danger Warning – danger zone.
Safety instructions 2 Safety instructions Intended use This device is intended to be used as mains voltage distributor and rack illumination. Use the device only as described in this user manual. Any other use or use under other operating con‐ ditions is considered to be improper and may result in personal injury or property damage. No liability will be assumed for damages resulting from improper use.
Safety instructions DANGER! Electric shock caused by high voltages inside Within the device there are areas where high voltages may be present. Never remove any covers. There are no user-serviceable parts inside. Do not use the device if covers, protectors or optical components are missing or damaged. DANGER! Electric shock caused by short-circuit Do not modify the mains cable or the plug. Failure to do so could result in electric shock/death or fire. If in doubt, seek advice from a registered electrician.
Safety instructions NOTICE! Power supply Before connecting the device, ensure that the input voltage (AC outlet) matches the voltage rating of the device and that the AC outlet is protected by a residual current circuit breaker. Failure to do so could result in damage to the device and possibly injure the user. Unplug the device before electrical storms occur and when it is unused for long periods of time to reduce the risk of electric shock or fire.
Features 3 Features n n n n n Power supply for up to eight electrical loads with IEC sockets Filters to protect the connected units against interference and voltage peaks Resettable electronic overload fuse Two dimmable rack lights Supply voltage monitoring via tricoloured LED chain voltage meter 10
Installation 4 Installation Unpack and check carefully there is no transportation damage before using the unit. Keep the equipment packaging. To fully protect the product against vibration, dust and moisture during transportation or storage use the original packaging or your own packaging material suitable for transport or storage, respectively. Create all connections while the device is off. Use the shortest possible high-quality cables for all connections.
Connections and operating elements 5 Connections and operating elements Front panel POWER LIGHTS DIMMER ON VM-100 ON 10 A M P OFF 190 MIN ö MAX 205 220 235 PULL # OFF PULL $ % voltage meter 12 250 & PROTECTION OUTLETS ' (
Connections and operating elements 1 [LIGHTS] Rack illumination switch 2 [DIMMER] Stepless dimmer control for rack illumination 3, 5 Extensible rack lights. Pull out the rack light and adjust the light beam as desired.
Connections and operating elements Rear panel ) * voltage meter 14
Connections and operating elements 8 Mains connection 9 IEC chassis sockets to supply up to eight devices VM-100 15
Maintenance 6 Maintenance Replacing the lamp DANGER! Electric shock caused by high voltages inside Within the device there are areas where high voltages may be present. Completely disconnect the device from the power supply before you open or remove covers. Mount all covers and attach them firmly before connecting the device again. Do not use the device if covers, protectors or optical components are missing or damaged.
Maintenance Procedure 1. Make sure that the device is turned off, disconnected from the mains and completely cooled down. 2. Pull out the faulty rack lamp (3, 5). Unscrew the cap from the end of the rack light. 3. Replace the lamp. 4. Screw the cap back onto the end of the rack light. 5. Reconnect the device to the mains.
Technical specifications 7 Technical specifications Output connections Power supply of further devices Supply voltage 220 - 240 V Fuse 10 A, resettable Maximum connected load 2200 W Mounting options Rack mounting, 1 RU Dimensions (W × H × D) 482 mm × 44 mm × 229 mm Weight 3 kg Ambient conditions Temperature range 0 °C…40 °C Relative humidity 20 %…80 % (non-condensing) 50/60 Hz voltage meter 18 8 × IEC chassis plug
Protecting the environment 8 Protecting the environment Disposal of the packaging mate‐ rial For the transport and protective packaging, environmentally friendly materials have been chosen that can be supplied to normal recycling. Ensure that plastic bags, packaging, etc. are properly disposed of. Do not just dispose of these materials with your normal household waste, but make sure that they are collected for recycling. Please follow the notes and markings on the packaging.
Notes voltage meter 20
Notes VM-100 21
Notes voltage meter 22
Musikhaus Thomann · Hans-Thomann-Straße 1 · 96138 Burgebrach · Germany · www.thomann.
