Ideal Workstation, BarStation™ and DryDock™ Installation Guide
Single Bowl Workstations & BarStation™ 18” Finished cutout 10” IWS 7S 1/2” Reveal front and back 16” IWS 5S IWS 6S IWS 4S IWS 3S IWS 2C IBS C Side view applies to all Single Bowl Workstations SUGGESTED GALLEY TAP AND TAP ACCESSORIES PLACEMENT GUIDE Galley Tap 1 3/8" min hole diameter (1 1/2" min hole diameter for fast water jet cut) Galley Soap Dispenser 1" min hole diameter Galley Deck Switch 1 3/8" min hole diameter Galley Automatic Strainer Basket knob 1" min and 1 3/8" max hole diameter Gall
Double Bowl Workstations 18” Finished cutout 10” IWS 7D 1/2” Reveal front and back 16” IWS 4D IWS 5D IWS 6D Side view applies to all Double Bowl Workstations SUGGESTED GALLEY TAP AND TAP ACCESSORIES PLACEMENT GUIDE Galley Tap 1 3/8" min hole diameter (1 1/2" min hole diameter for fast water jet cut) Galley Soap Dispenser 1" min hole diameter Galley Deck Switch 1 3/8" min hole diameter Galley Automatic Strainer Basket knob 1" min and 1 3/8" max hole diameter Galley Hot and Cold Water Dispenser 1 3/
In Stock DryDock™ Workstations 18” Finished cutout 10” IWS 4S + DD18 1/2” Reveal front and back 16” IWS 3S + DD12 IWS 3S + DD18 IWS 4S + DD12 Side view applies to all DryDock™ Workstations shown SUGGESTED GALLEY TAP AND TAP ACCESSORIES PLACEMENT GUIDE Galley Tap 1 3/8" min hole diameter (1 1/2" min hole diameter for fast water jet cut) Galley Soap Dispenser 1" min hole diameter Galley Deck Switch 1 3/8" min hole diameter Galley Automatic Strainer Basket knob 1" min and 1 3/8" max hole diameter Gal
IMPORTANT Unlike typical undermount kitchen sink installations, The Galley Workstation is installed in the cabinet prior to the counter being templated. A support structure, (cleat system of wood frame), will need to be constructed and mounted inside the base cabinet(s) and recessed 1/16" from the top. The Workstation and Tap require a minimum of 22 1/2” inside the cabinet. For 24” deep inset cabinets installed against a wall the cabinet must be pulled 1” away from the wall.
1. CONSTRUCT SUPPORT STRUCTURE a) A support frame (cleat system) will need to be built and installed into the cabinet(s). This frame will support the weight of the Workstation. Note: Clips are NOT to be used. b) Construct the support frame so that the inside dimensions are 1/2" larger than the basin’s inside dimensions. Please refer to pages 1-3 for your Workstation dimensions. 1” x 6” HARDWOOD BOARDS ARE RECOMMENDED EXCEPT FOR WORKSTATION + DRYDOCK, FOR WHICH 1” X 2” ARE RECOMMENDED.
YOU ARE NOW READY FOR THE COUNTERTOP FABRICATOR Counter Top Installation Use the white template tray affixed to the Workstation flanges as your guide for the front to back cut-out. Refer to pages 1-3 for your overall cut-out dimensions or refer to the drawing on the template tray. Note: The front to back cutout dimension must be exactly 18”. 1. Cover what will be the exposed 1/2” of the front and back flanges, and the 1/4“ of the side flanges with painters tape for easy cleaning of excess silicone. 2.
The Galley Workstation Limited Lifetime Warranty 1. GALLEY WORKSTATION LIMITED LIFETIME WARRANTY - Seller provides a Limited Lifetime Warranty. Seller warrants its stainless steel sink, installed in a residential application, to be free from manufacturing defects in materials and workmanship under normal residential usage. This Limited Lifetime Warranty is subject to the warranty conditions and limitations as set forth below. 2.
