DEV ISE V www.devaise.
IMPORTANT INFORMATION READ CAREFULLY. KEEP THIS INFORMATION FOR FURTHER REFERENCE. ••• GENERAL GUIDELINES Please read the following instruction carefully and use the product accordingly. Please keep this manual and hand it over when you transfer the product. This summary may not include every detail of all variations and considered steps. Please contact us when further information and help are needed. •• • NOTES Please follow the assembly instructions precisely and only use the product as intended.
If you have any further questions, please feel free to contact us by email or official website: www.devaise.com We will reply ASAP. Before installation, please make sure you have all the hardware, the serial numbers are properly labeled corresponging to the list, and the quantity is correct.
DEV ISE V EXPLODED DRAWING 5 6 6 7 2 4 3 1 8 9 8 9 10 10 9 11 15 12 13 10 16 1 14 9
DEV ISE V PARTS A X36 B X12 C X36 D X2 E X1 F X2 G X52 M4x14 = = CL + E1 X2 DL + DR H X6 + E2 X2 I X3 J X2 K X2 L X16 M X8 N X4 O X1 + CR O1 O2 O3 2
DEV ISE V REMARK CR DR CL DL 1. Press the plastic part in the indicated direction to separate drawer runner E1 and E2 before assembling. 2. Please grip the E1 part while sliding the E2 PUL L part.
DEV ISE V A X6 1 B X4 REMARK 1. Please do not screw A too deep or too shallow. DEV ISE V Appropriate position Too deep Too shallow 2. Put a blanket under the board to avoid scratch or damage.
DEV ISE V 2 B ×8 CL CL X2 NT CR 3 BOTTOM REMARK When installing, please make sure the screws are flattened, Not crooked; Otherwise the drawers will not be installed perfectly.
DEV ISE V G X4 3 M4x14 E1 X2 FRONT FRO NT TOP 2 3 BOTTOM REMARK 1. Please locate the holes from the back of part E1 2.
DEV ISE V 4/21 A X6 4 A 6 5 C X6 5 C ×6 4 2 3 5 4 3 2 5 REMARK Let the grooves on part to the groove on part 5 .
DEV ISE V 6 6 6 2 4 5 C X6 7 1 4 3 C 2 6 1 5 4 3 2 5 8
DEV ISE V 8 G X16 J X2 M4x14 K X2 1 4 3 K ×2 2 5 O FR 9 NT J ×2 A X8 H X4 I X2 A 8 H ×4 15 11 I 9 I
DEV ISE V A X4 10 H X2 I X1 A 4 H 2 16 I A X8 11 A 4 8 ×2 10
DEV ISE V A X4 12 4 A 12 C X8 13 8 9 C 9 4 8 9 9 8 9 9 10 11 ×2
DEV ISE V C X4 14 9 15 C 8 4 9 9 15 C X4 15 9 11 C 4 8 9 9 11 12
DEV ISE V 16 G X4 DR X1 M4x14 DL X1 8 9 9 15 G DR FRONT DL 10 DL 9 8 FRONT FRONT G FRONT DL 1 13 4 3 10 12
DEV ISE V 17 G X4 DR X1 M4x14 9 8 DL X1 9 11 G DR FRONT DL 10 9 DL 8 C X4 18 12 13 12 14 13 FRONT FR ON T C 14 4 FRONT FRONT long 13 short 14
DEV ISE V F X2 19. 19 (1) 12 A4 14 13 10 (2) Letter Size F F As shown in Fig. (1) installation method, the A4 Size file can be hung after installation. 12 16 As shown in Fig. (2) installation method, the Letter Size file can be hung after installation.
DEV ISE V G X4 21 M4x14 E2 X2 O FR E2 12 NT E2 14 13 16 FRONT FRONT G FRONT E2 9 7 1 16
DEV ISE V 22 11 15 2 3 4 23 1 FRONT 11 15 FRONT 2 FRONT BALL BEARING FRONT 17 BALL BEARING REMARK 1. Please full extend the slide runners. 2. Simply push the ball bearing cart all the way to the end of the slide(in both sides).
DEV ISE V 24 REMARK 1. Align the slide runners on the drawer with the unit and push it carefully inside until it stops. 2. If the drawer does not go in smoothly please take it out and repeat the step.
DEV ISE V 26 NT FRONT FRO long 7 7 short REMARK The long shadow part is in front and the short one is inside. 7 REMARK Please make the groove on board 7 27 match with the part N .
DEV ISE V O X1 28 O1 O2 G X4 M4x14 O3 G ×4 O1 O2 O3 20
DEV ISE V G X8 29 M4x14 M X8 M M G G 21 + M M M M ×8
