Instructions
3130
METEOTIME PRIMO – Weather Info Center
11. Display of the measured values of the outdoor transmitters
11.1 Static display
• Press the CHANNEL button to select the measurements from the different outdoor transmitters on channel 1, 2 or
3.
• With the MEM button, you can recall the highest and lowest temperature and humidity values for all installed
transmitters.
11.2 Channel auto-scan display
• To enable an automatic scan of all channels, press and hold the CHANNEL button, until the icon is displayed.
The measurements from each remote channel will be displayed in 5 seconds alternatively.
NOTE: the channel auto-scan feature can only be activated if there is more than one outdoor transmitters operating
and they are set to different channels.
12. Alarm functions
• There are three different alarm functions:
Weekday alarm (W-ALM):
• This is a repeat alarm that will be activated daily from Monday to Friday at a set time.
Single alarm (S-ALM):
• This is a single alarm that will be activated once at a set time.
Pre-alarm (P-ALM):
• Earlier wake-up time in case of frost.
12.1 Setting of the alarms
• Press the SET button to toggle between weekday alarm (W-ALM), single alarm (S-ALM) or pre-alarm (P-ALM).
•
OFF
appears on the display of each alarm when the alarm is turned off..
12.1.1 Weekday alarm (W-ALM) and Single alarm (S-ALM)
• Press the SET button to set the weekday alarm (W-ALM) or the single alarm (S-ALM).
• Press and hold the SET button for 3 seconds and the hour digits flash.
• Press the + or – button to set the hours.
• Press SET button to confirm and the minutes digits flash.
METEOTIME PRIMO – Weather Info Center
• Press the + or – button to set the minutes.
• Press the SET button to exit and the respective alarm symbols or will be activated.
12.1.2 Pre-Alarm – (alarm for frost alert = outdoor temperature at transmitter 1 ≤ 2°C)
• If the weekday (W-ALM) or the single day (S-ALM) alarm is set and an outdoor transmitter is installed on channel
1, the pre-alarm (P-ALM) can be programmed.
• Press several times the SET button, to enter the the frost alert setting mode P-ALM.
• Press and hold the SET button for 3 seconds.
• The number 15 will be flashing, meaning that if selected, the alarm will sound 15 minutes earlier than the weekday
or single alarm.
• Select the frost alert interval in 15 minutes increments between 15 and 90 minutes by using the + or – button.
• Press the SET button to exit and the alarm symbol will be activated.
12.2 Activate and deactivate the alarms
• When an alarm sounds, the respective alarm icons
,
or will be flashing. The backlight turns on
for 5 seconds.
• Press the SNOOZE/LIGHT button to activate the snooze function.
• The alarm is interrupted for 5 minutes.
• Press + or – to stop the alarm immediately.
• If no button is pressed, the increasing alarm will sound for 2 minutes.
• Press the SET button in normal mode to toggle between the weekday alarm (W-ALM), single alarm (S-ALM) or
pre-alarm (P-ALM).
• To turn off the alarm, press the – button to change the alarm time display to
OFF
.
• Press the + button to activate the alarm function again. 00:00 or the last adjusted alarm time appears.
13. Backlight
• Press the SNOOZE/LIGHT button. The backlight turns on for 5 seconds.
14. Care and maintenance
• Clean the devices with a soft damp cloth. Do not use solvents or scouring agents.
• Remove the batteries from all devices if you do not use the weather station for a long period of time.
• Store the devices in a dry place.
01_TFA_No. 35.1156_Anleitung 29.11.2019 6:59 Uhr Seite 16