Instructions
Instruction manual
Cat.-No. 30.3061
Wireless thermometer
Thank you for choosing this instrument from TFA.
1. Before you start using it
• Please make sure to read the instruction manual carefully.
Following and respecting the instructions in your manual will prevent damage to your instru-
ment and loss of your statutory rights arising from defects due to incorrect use.
• We shall not be liable for any damage occurring as a result of non following of these instruc-
tions. Likewise, we take no responsibility for any incorrect readings and for any conse-
quences which may result from them.
• Please take particular note of the safety advice!
• Please keep this instruction manual for future reference.
2. Delivery contents
• Wireless thermometer (basic station)
• Outdoor transmitter (Cat.-No.: 30.3220.02)
• Instruction manual
3. Field of operation and all the benefits of your new instrument at a glance
• Outdoor temperature wireless (max. 30 m)
• Indoor temperature
• Maximum and minimum values
• Clock
• For table standing
4. For your safety
• This product is exclusively intended for the field of application described above.
• It should only be used as described within these instructions.
• Unauthorized repairs, modifications or changes to the product are prohibited.
Caution!
Risk of injury:
• Keep these devices and the batteries out of reach of children.
• Batteries contain harmful acids and may be hazardous if swallowed. If a battery is swallowed,
this can lead to serious internal burns and death within two hours. If you suspect a battery
could have been swallowed or otherwise caught in the body, seek medical help immediately.
• Batteries must not be thrown into a fire, short-circuited, taken apart or recharged. Risk of explo-
sion!
• Low batteries should be changed as soon as possible to prevent damage caused by leaking.
Never use a combination of old and new batteries together, nor batteries of different types.
• Wear chemical-resistant protective gloves and safety glasses when handling leaking batteries..
Important information on product safety!
• Do not place your device near extreme temperatures, vibrations or shocks.
• Protect it from moisture.
• The outdoor transmitter is protected against splash water, but is not watertight. Placed outside,
choose a shady and dry position for the transmitter.
5. Getting started
5.1 Insert the batteries
• Put the devices upside down on a table.
• Pull off the protecting foil from the display of the basis station and outdoor transmitter.
• Avoid getting close to possible interference sources (Electronic devices and radio installations).
• Important: First insert the batteries into the basic station and then into the outdoor trans-
mitter.
• Open the battery compartment of the basic station and insert two new batteries 1.5 V AAA,
polarity as illustrated.
• All LCD segments will be displayed briefly.
• Close the battery compartment again.
• Open the screwed battery compartment of the outdoor transmitter by lifting up the stand.
• Insert two new batteries 1,5 V AAA polarity as illustrated.
• Close the battery compartment again.
5.2 Reception of outdoor transmitter
• After inserting the batteries into the outdoor transmitter the transmitter will automatically trans-
mit the temperature. The reception symbol will be flashing on the display.
• If the reception of outdoor temperature fails, "- -" appears on the display. Check the batteries
and try it again. Check if there is any source of interference.
• You can start the initialization manually. Hold the MAX/MIN button on the basic station for three
seconds.
• On the display of the outdoor temperature appears "--.-" and the reception signal symbol will be
flashing. The basic station will scan again the outdoor temperature.
6. Operation
• The device will automatically quit the setting mode if no button is pressed for a few seconds.
6.1 Setting of the time
• Press and hold SET button in normal mode.
• 0 will be flashing on the display.
• Press the MAX/MIN button to adjust
the
hours.
•
Press the SET button again to make the settings in the following sequence: the minutes (0 - default)
and the 12 or 24 hours system (24 - default) and adjust it with the MAX/MIN button.
• Confirm the setting with the SET button.
• The display shows the adjusted time.
6.2 Maximum/Minimum function
• Press the MAX/MIN button in normal mode.
• MAX appears on the display.
• On the display appear the maximum measured values since the last reset.
• Press the MAX/MIN button again.
• MIN appears on the display.
• On the display appear the minimum measured values since the last reset.
Instruction manual
Cat.-No. 30.3061
TFA_No. 30.3061_Anl_11_19_Web 04.11.2019 11:46 Uhr Seite 3