Datasheet

XTR110
3
SBOS141C
www.ti.com
XTR110AG, KP, KU XTR110BG
PARAMETER CONDITIONS MIN TYP MAX MIN TYP MAX UNITS
TRANSMITTER
Transfer Function
Input Range: V
IN1
(5)
Specified Performance 0 +10 * * V
V
IN2
Specified Performance 0 +5 * * V
Current, I
O
Specified Performance
(1)
420* *mA
Derated Performance
(1)
040* *mA
Nonlinearity 16mA/20mA Span
(2)
0.01 0.025 0.002 0.005 % of Span
Offset Current, I
OS
I
O
= 4mA
(1)
Initial
(1)
0.2 0.4 0.02 0.1 % of Span
vs Temperature
(1)
0.0003 0.005 * 0.003 % of Span/°C
vs Supply, V
CC
(1)
0.0005 0.005 * * % of Span/V
Span Error I
O
= 20mA
Initial
(1)
0.3 0.6 0.05 0.2 % of Span
vs Temperature
(1)
0.0025 0.005 0.0009 0.003 % of Span/°C
vs Supply, V
CC
(1)
0.003 0.005 * * % of Span/V
Output Resistance From Drain of FET (Q
EXT
)
(3)
10 x 10
9
* Ω
Input Resistance V
IN1
27 * kΩ
V
IN2
22 * kΩ
V
REF
In 19 * kΩ
Dynamic Response
Settling Time To 0.1% of Span 15 * µs
To 0.01% of Span 20 * µs
Slew Rate 1.3 * mA/µs
VOLTAGE REFERENCE
Output Voltage +9.95 +10 +10.05 +9.98 * +10.02 V
vs Temperature 35 50 15 30 ppm/°C
vs Supply, V
CC
Line Regulation 0.0002 0.005 * * %/V
vs Output Current Load Regulation 0.0005 0.01 * * %/mA
vs Time 100 * ppm/1k hrs
Trim Range –0.100 +0.25 * * V
Output Current Specified Performance 10 * mA
POWER SUPPLY
Input Voltage, V
CC
+13.5 +40 * * V
Quiescent Current Excluding I
O
3 4.5 * * mA
TEMPERATURE RANGE
Specification: AG, BG –40 +85 * * °C
KP, KU 0 +70 °C
Operating: AG, BG –55 +125 * * °C
KP, KU –25 +85 °C
ELECTRICAL CHARACTERISTICS
At T
A
= +25°C and V
CC
= +24V and R
L
= 250Ω**, unless otherwise specified.
I
O
= 10 [(V
REF
In/16) + (V
IN1
/4) + (V
IN2
/2)] /R
SPAN
* Specifications same as AG/KP grades. ** Specifications apply to the range of R
L
shown in Typical Performance Curves.
NOTES: (1) Including internal reference. (2) Span is the change in output current resulting from a full-scale change in input voltage. (3) Within compliance range limited
by (+V
CC
– 2V) +V
DS
required for linear operation of the FET. (4) For V
REF
adjustment circuit see Figure 3. (5) For extended I
REF
drive circuit see Figure 4. (5) Unit may
be damaged. See
Input Voltage Range section.